User Manual
Table Of Contents
- Table of Contents
- About This Guide
- 1 Product Introduction
- 2 Hardware Installation
- 3 Getting Started
- 4 SmartConsole Utility
- 5 Configuration
- Smart Wizard Configuration
- Web-based Management
- Tool Bar > Save Menu
- Tool Bar > Tool Menu
- Tool Bar > Smart Wizard
- Tool Bar > Online Help
- Function Tree
- Device Information
- System > System Settings
- System > DHCP Auto Configuration
- System > Trap Settings (For SmartConsole)
- System > Port Settings
- System > SNMP Settings > SNMP Global State
- System > SNMP Settings > User/Group Table
- System > SNMP Settings > SNMP Group Access Table
- System > SNMP Settings > SNMP View Table
- System > SNMP Settings > Community Table
- System > SNMP Settings > Host Table
- System > SNMP Settings > SNMP Engine ID
- System > SNMP Settings > SNMP Trap Settings
- System > Password Access Control
- System > System Log Settings
- Configuration > Jumbo Frame
- Configuration > 802.1Q VLAN
- Configuration > 802.1Q Management VLAN
- Configuration > Auto Surveillance VLAN > Auto Surveillance VLAN Settings
- Configuration > Voice VLAN > Voice VLAN Settings
- Configuration > Voice VLAN > Voice VLAN OUI Settings
- Configuration > Link Aggregation > Port Trunking
- Configuration > Link Aggregation > LACP Port Settings
- Configuration > IGMP Snooping > IGMP Snooping Configuration
- Configuration > Multicast Filtering Mode
- Configuration > Port Mirroring
- Configuration > Power Saving
- Configuration > Loopback Detection
- Configuration > SNTP Settings > Time Settings
- Configuration > SNTP Settings > TimeZone Settings
- Configuration > Spanning Tree > STP Global Settings
- Configuration > Spanning Tree > STP Port Settings
- QoS > Storm Control
- QoS > Bandwidth Control
- QoS > 802.1p/DSCP Priority Settings
- Security > Trusted Host
- Security > Safeguard Engine
- Security > ARP Spoofing Prevention
- Security > Port Security
- Security > SSL Settings
- Security > 802.1X > 802.1X Settings
- Security > MAC Address Table > Static MAC
- Security > MAC Address Table > Dynamic Forwarding Table
- Security > DHCP Server Screening > DHCP Server Screening Port Setting
- Monitoring > Statistics
- Monitoring > Cable Diagnostics
- Monitoring > System Log
- ACL > ACL Configuration Wizard
- ACL > ACL Profile List
- ACL > ACL Finder
- PoE > PoE Port Settings (DGS-1210-10P only)
- PoE > PoE System Settings (DGS-1210-10P only)
- Time-Based PoE > Time Range Settings (DGS-1210-10P only)
- LLDP > LLDP Global Settings (DGS-1210-10P only)
- LLDP > LLDP Remote Port Information (DGS-1210-10P only)
- LLDP > LLDP MED Settings (DGS-1210-10P only)
- 6 Command Line Interface
- Appendix A - Ethernet Technology
- Appendix B - Technical Specifications
- Appendix C – Rack mount Instructions
- _
5 Configuration D-Link Web Smart Switch User Manual
20
5 Configuration
The features and functions of the D-Link Web Smart Switch can be configured for optimum use through the
Web-based Management Utility.
Smart Wizard Configuration
After a successful login, the Smart Wizard will guide you through essential settings of the D-Link Web Smart
Switch. If you do not plan to change anything, click Exit to leave the Wizard and enter the Web Interface.
You can also skip it by clicking Don’t show Smart Wizard next time for the next time you logon to the Web-
based Management.
Password Settings
Password setting allows you to change the login password of the device. Type the desired new password in
the Switch Password box and again in the Confirm Switch Password, then click the Apply button to make
it effective.
Figure 29 – Configure Password in Smart Wizard