User Manual
Table Of Contents
- Table of Contents
- About This Guide
- 1 Product Introduction
- 2 Hardware Installation
- 3 Getting Started
- 4 SmartConsole Utility
- 5 Configuration
- Smart Wizard Configuration
- Web-based Management
- Tool Bar > Save Menu
- Tool Bar > Tool Menu
- Tool Bar > Smart Wizard
- Tool Bar > Online Help
- Function Tree
- Device Information
- System > System Settings
- System > DHCP Auto Configuration
- System > Trap Settings (For SmartConsole)
- System > Port Settings
- System > SNMP Settings > SNMP Global State
- System > SNMP Settings > User/Group Table
- System > SNMP Settings > SNMP Group Access Table
- System > SNMP Settings > SNMP View Table
- System > SNMP Settings > Community Table
- System > SNMP Settings > Host Table
- System > SNMP Settings > SNMP Engine ID
- System > SNMP Settings > SNMP Trap Settings
- System > Password Access Control
- System > System Log Settings
- Configuration > Jumbo Frame
- Configuration > 802.1Q VLAN
- Configuration > 802.1Q Management VLAN
- Configuration > Auto Surveillance VLAN > Auto Surveillance VLAN Settings
- Configuration > Voice VLAN > Voice VLAN Settings
- Configuration > Voice VLAN > Voice VLAN OUI Settings
- Configuration > Link Aggregation > Port Trunking
- Configuration > Link Aggregation > LACP Port Settings
- Configuration > IGMP Snooping > IGMP Snooping Configuration
- Configuration > Multicast Filtering Mode
- Configuration > Port Mirroring
- Configuration > Power Saving
- Configuration > Loopback Detection
- Configuration > SNTP Settings > Time Settings
- Configuration > SNTP Settings > TimeZone Settings
- Configuration > Spanning Tree > STP Global Settings
- Configuration > Spanning Tree > STP Port Settings
- QoS > Storm Control
- QoS > Bandwidth Control
- QoS > 802.1p/DSCP Priority Settings
- Security > Trusted Host
- Security > Safeguard Engine
- Security > ARP Spoofing Prevention
- Security > Port Security
- Security > SSL Settings
- Security > 802.1X > 802.1X Settings
- Security > MAC Address Table > Static MAC
- Security > MAC Address Table > Dynamic Forwarding Table
- Security > DHCP Server Screening > DHCP Server Screening Port Setting
- Monitoring > Statistics
- Monitoring > Cable Diagnostics
- Monitoring > System Log
- ACL > ACL Configuration Wizard
- ACL > ACL Profile List
- ACL > ACL Finder
- PoE > PoE Port Settings (DGS-1210-10P only)
- PoE > PoE System Settings (DGS-1210-10P only)
- Time-Based PoE > Time Range Settings (DGS-1210-10P only)
- LLDP > LLDP Global Settings (DGS-1210-10P only)
- LLDP > LLDP Remote Port Information (DGS-1210-10P only)
- LLDP > LLDP MED Settings (DGS-1210-10P only)
- 6 Command Line Interface
- Appendix A - Ethernet Technology
- Appendix B - Technical Specifications
- Appendix C – Rack mount Instructions
- _
3 Getting Started D-Link Web Smart Switch User Manual
10
3 Getting Started
This chapter introduces the management interface of D-Link Web-Smart Switch.
Management Options
The D-Link Web Smart Switch can be managed through any port on the device by using the Web-based
Management, or through any PC using the SmartConsole Utility.
Each switch must be assigned its own IP Address, which is used for communication with the Web-Based
Management or a SNMP network manager. The PC should have an IP address in the same range as the
switch. Each switch can allow up to four users to access the Web-Based Management concurrently.
However, if you want to manage multiple D-Link Web Smart Switches, the SmartConsole Utility is a more
convenient choice. By using the SmartConsole Utility, you do not need to change the IP address of your PC
and it is easier to initialize multiple Smart Switches.
Please refer to the following installation instructions for the Web-based Management and the SmartConsole
Utility.
Using Web-based Management
After a successful physical installation, you can configure the Switch, monitor the network status, and display
statistics using a web browser.
Supported Web Browsers
The embedded Web-based Management currently supports the following web browsers:
Internet Explorer 6 or higher
Netscape 8 or higher
Mozilla
Firefox 1.5/2.0 or higher
Connecting to the Switch
You will need the following equipment to begin the web configuration of your device:
1. A PC with a RJ-45 Ethernet connection
2. A standard Ethernet cable
Connect the Ethernet cable to any of the ports on the front panel of the switch and to the Ethernet port on the
PC.
Figure 13 – Connected Ethernet cable