User Manual
Table Of Contents
- Table of Contents
- About This Guide
- 1 Product Introduction
- 2 Hardware Installation
- 3 Getting Started
- 4 SmartConsole Utility
- 5 Configuration
- Smart Wizard Configuration
- Web-based Management
- Tool Bar > Save Menu
- Tool Bar > Tool Menu
- Tool Bar > Smart Wizard
- Tool Bar > Online Help
- Function Tree
- Device Information
- System > System Settings
- System > DHCP Auto Configuration
- System > Trap Settings (For SmartConsole)
- System > Port Settings
- System > SNMP Settings > SNMP Global State
- System > SNMP Settings > User/Group Table
- System > SNMP Settings > SNMP Group Access Table
- System > SNMP Settings > SNMP View Table
- System > SNMP Settings > Community Table
- System > SNMP Settings > Host Table
- System > SNMP Settings > SNMP Engine ID
- System > SNMP Settings > SNMP Trap Settings
- System > Password Access Control
- System > System Log Settings
- Configuration > Jumbo Frame
- Configuration > 802.1Q VLAN
- Configuration > 802.1Q Management VLAN
- Configuration > Auto Surveillance VLAN > Auto Surveillance VLAN Settings
- Configuration > Voice VLAN > Voice VLAN Settings
- Configuration > Voice VLAN > Voice VLAN OUI Settings
- Configuration > Link Aggregation > Port Trunking
- Configuration > Link Aggregation > LACP Port Settings
- Configuration > IGMP Snooping > IGMP Snooping Configuration
- Configuration > Multicast Filtering Mode
- Configuration > Port Mirroring
- Configuration > Power Saving
- Configuration > Loopback Detection
- Configuration > SNTP Settings > Time Settings
- Configuration > SNTP Settings > TimeZone Settings
- Configuration > Spanning Tree > STP Global Settings
- Configuration > Spanning Tree > STP Port Settings
- QoS > Storm Control
- QoS > Bandwidth Control
- QoS > 802.1p/DSCP Priority Settings
- Security > Trusted Host
- Security > Safeguard Engine
- Security > ARP Spoofing Prevention
- Security > Port Security
- Security > SSL Settings
- Security > 802.1X > 802.1X Settings
- Security > MAC Address Table > Static MAC
- Security > MAC Address Table > Dynamic Forwarding Table
- Security > DHCP Server Screening > DHCP Server Screening Port Setting
- Monitoring > Statistics
- Monitoring > Cable Diagnostics
- Monitoring > System Log
- ACL > ACL Configuration Wizard
- ACL > ACL Profile List
- ACL > ACL Finder
- PoE > PoE Port Settings (DGS-1210-10P only)
- PoE > PoE System Settings (DGS-1210-10P only)
- Time-Based PoE > Time Range Settings (DGS-1210-10P only)
- LLDP > LLDP Global Settings (DGS-1210-10P only)
- LLDP > LLDP Remote Port Information (DGS-1210-10P only)
- LLDP > LLDP MED Settings (DGS-1210-10P only)
- 6 Command Line Interface
- Appendix A - Ethernet Technology
- Appendix B - Technical Specifications
- Appendix C – Rack mount Instructions
- _
1 Product Introduction D-Link Web Smart Switch User Manual
5
5
Port Link/Act/Speed LED (1-20, 21F, 22F, 23F, 24F, 21T, 22T, 23T, 24T): The Link/Act/Speed LED flashes,
which indicates a network link through the corresponding port. Blinking indicates that the Switch is either
sending or receiving data to the port. When a port has an amber light, this indicates that the port is running
on 10M or 100M. When it has a green light it is running on 1000M.
Reset: Press the Reset button to reset the Switch back to the default settings. All previous changes will be
lost.
NOTE: On the DGS-1210-24, the SFP ports are
shared with normal RJ-45 ports 49 and 50. When
optical transceiver is inserted to SFP port and link
up, the RJ-45 port cannot be used.
CAUTION: The MiniGBIC ports should use UL
listed Optical Transceiver product, Rated Laser
Class I. 3.3Vdc.
Rear Panel
Figure 6 – DGS-1210-24 Rear Panel
Power: Connect the supplied AC power cable to this port.
DGS-1210-48
48-Port 10/100/1000Mbps with 4 Combo SFP Slot Web Smart Switch.
Front Panel
Figure 7 – DGS-1210-48 Front Panel
Power LED
: The Power LED lights up when the Switch is connected to a power source.
Port Link/Act/Speed LED (1-44, 45F, 46F, 47F, 48F, 45T, 46T, 47T, 48T): The Link/Act/Speed LED flashes,
which indicates a network link through the corresponding port. Blinking indicates that the Switch is either
sending or receiving data to the port. When a port has an amber light, this indicates that the port is running
on 10M or 100M. When it has a green light it is running on 1000M.
Fan Err: The Fan Err LED lights red when the fan fails. It is off when all fans work normally.
Reset: Press the Reset button to reset the Switch back to the default settings. All previous changes will be
lost.
NOTE: On the DGS-1210-48, the SFP ports are
shared with normal RJ-45 ports 49 and 50. When
the optical transceiver is inserted to the SFP port
and linked up, the RJ-45 port cannot be used.
SFP ports for optical transceivers