Building Networks for People Information Security gateway(ISG) This Quick Guide will guide you through the installation process.
DFL-M510 Quick Installation Guide 1.Before You Begin 1.1 Check Your Package Contents................................................................1 1.2 DFL-M510 Introduction...........................................................................2 1.3 DFL-M510 Architecture...........................................................................3 2.Identifying Components 2.1 Front View..............................................................................................4 2.2 Rear View........
1 DFL-M510 Before You Begin 1.1 Check Your Package Contents Thank you for purchasing DFL-M510 Information Security Gateway. Before continuing, please check the contents of the product package.
DFL-M510 Quick Installation Guide 1.2 DFL-M510 Introduction DFL-M510 is a transparent network device which is installed in In-Line mode with “Hardware Bypass” function, without any change of current network architecture to control/manage information traffic flow (IM, P2P and Streaming Media … etc.) from intranet and detect/drop the traffic with health concerns (Trojan, Illegal agent and Network worm … etc.) Based on the policy rules applied to specific Group/Hosts/subnet.
DFL-M510 Quick Installation Guide 1.3 DFL-M510 Architecture Without Firewall When there is no firewall involved, we suggest to place DFLM510 behind the router or ADSL modem. Below illustrates the recommended structure. ADSL Router DFL-M510 WAN Port Switch LAN Port With Firewall When there is a firewall, placing the DFL-M510 between the firewall and the LAN is recommended. The recommended structure is illustrated as following.
2 Identifying Components The following illustrations show the front view, rear view, LCD Panel and status LEDs of the DFL-M510. 2.1 Front View 1 2 3 1. See “LCD Panel” below 2. See”Status LEDs” below 3. LCD Navigation Buttons * 4. WAN Port with hardwave bypass * 5. LAN Port with hardwave bypass 6. 4 5 6 Console Port Note: * Hardware Bypass – A built-in failure-proof function of the DFL-M510.
DFL-M510 Quick Installation Guide 2.2 Rear View 1 1. Power socket 2. Power switch 2 2.
DFL-M510 Quick Installation Guide 2.4 LCD Panel Main Menu Sub-Menu Description Device Status System Info. Firmware Ver.: Policy Ver.: Policy Number: Current Date: Current Time: Dev. Up Time: CPU Load: Memory Usage: Current Session: Traffic Info. WAN RX: WAN Drop: LAN RX: LAN Drop: Traffic Level: Alert Monitor Traffic Alert: IP Info. Device Name: IP Address: IP Mask: Gateway IP: DNS IP: Operation Mode: Interface Info.
DFL-M510 Quick Installation Guide 2.
Connecting the DFL-M510 3 The client’s network structure can be set up with/without a firewall. 3.1 Setting up without a firewall If your network is not behind a firewall, the DFL-M510 is placed between the ADSL or router and switch. Refer to the following: Connect a UTP cable from the ADSL router to the WAN port on the DFL-M510. Connect a UTP cable from the LAN port on the DFL-M510 to the switch.
DFL-M510 Quick Installation Guide 3.2 Setting up with a firewall If your network is behind a firewall, the DFL-M510 is placed between firewall and LAN. Refer to the following: Connect a UTP cable from the firewall to the WAN port on the DFL-M510. Connect a UTP cable from the LAN port on the DFL-M510 to the LAN. ADSL Router Firewall WAN Port DFL-M510 LAN Port Note: If you are deploying DFL-M510 over the VLAN (802.1q) network, you have to configure the VLAN setting before putting in the network.
Configure DFL-M510 4 The DFL-M510 GUI is a Web-based application that allows you to manage the DFL-M510. The GUI is a java applet application. Before accessing the GUI from any PC, note the following: You must install Java Runtime (1.4.2 or above) as described below Pentium 4, 2.0 GHz 512 MB RAM Refer to the following to log on to the DFL-M510. 4.
DFL-M510 Quick Installation Guide DFL-M510 Welcome page. Either install the Java Runtime from the accessary CD first or login to DFL-M510 directly. Java Runtime is required to login DFL-M510 , Please install the Java Runtime program. Click “Always” to continue and prevent screen appearing again, The login screen appears. Click Always to trust the signed applet distributed by “D-Link”.
DFL-M510 Installation Guide Login to the DFL-M510 with ID/Password. type the default ID/Password ID: admin Password: admin select the preferred language, and then click Login The computer requires to start Java Runtime therefore the log-on time would be around 20 seconds. Note: The Setup Wizard would be running automatically when you login into DFL-M510 first time.
DFL-M510 Installation Guide 4.2 Setup Wizard Running the Setup Wizard Welcome to the DFL-M510 Setup Wizard. This wizard will guide you through the setup of your DFL-M510 Step1 - Setup Wizard welcome page 3 Steps to guide you to finish the quick configuration. Click Next Step2 - Set up the IP/Subnet mask and default gateway After set up the IP information for DFL-M510.
DFL-M510 Installation Guide 4.2 Setup Wizard (Continued) Step3 - Choose the Applications you want to block Choose the applications that you want to block in your network.
DFL-M510 Installation Guide 4.2 Setup Wizard (Continued) Step5 - Select ”Yes” to go to Real-Time Monitor.
WARRANTY 5 Warranty FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this manual, may cause harmful interference to radio communications.
DFL-M510 Installation Guide Attenzione! Il presente prodotto appartiene alla classe A. Se utilizzato in ambiente domestico il prodotto può causare interferenze radio, nel cui caso è possibile che l`utente debba assumere provvedimenti adeguati.
