User Manual and Operating Guide

ManualsBrandsD-Link ManualsWasher/DryerDES-3200 Series Washer/Dryer

Summary of content (652 pages)

PAGE 1
PAGE 2
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Table of Contents Chapter 1 Using Command Line Interface............................................................................................. 1 Chapter 2 Basic Command List ............................................................................................................. 8 Chapter 3 802.1Q VLAN Command List..............................................................................................
PAGE 3
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 35 Layer 2 Protocol Tunneling (L2PT) Command List...........................................................334 Chapter 36 Link Aggregation Command List .......................................................................................338 Chapter 37 Link Layer Discovery Protocol (LLDP) Command List...................................................... 345 Chapter 38 Loop Back Detection (LBD) Command List ..
PAGE 4
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 71 Trace Route Command List ..............................................................................................606 Chapter 72 Traffic Control Command List ...........................................................................................609 Chapter 73 Traffic Segmentation Command List.................................................................................
PAGE 5
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 1 Interface Using Command Line The Switch can be managed through the Switch’s serial port, Telnet, SNMP or the Web-based management agent. The Command Line Interface (CLI) can be used to configure and manage the Switch via the serial port or Telnet interfaces. This manual provides a reference for all of the commands contained in the CLI.
PAGE 6
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide The Switch is also assigned a unique MAC address by the factory. This MAC address cannot be changed, and can be found on the initial boot console screen – shown below. Boot Procedure V4.00.002 ------------------------------------------------------------------------------Power On Self Test ........................................ MAC Address H/W Version 100 % : 00-01-02-03-04-00 : C1 Please Wait, Loading 4.04.
PAGE 7
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide There are a number of helpful features included in the CLI. Entering the ? command will display a list of all of the top-level commands. ..
PAGE 8
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide :admin#config account Command: config account Next possible completions: :admin#config account In the above example, the command config account was entered without the required parameter , the CLI returned the Next possible completions: prompt. The up arrow cursor control key was pressed to re-enter the previous command (config account) at the command prompt.
PAGE 9
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide :admin#show Command: show Next possible completions: 802.1p 802.
PAGE 10
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide create ipif {} {secondary | state [enable | disable] | proxy_arp [enable | disable] {local [enable | disable]}} users must supply an IP interface name for ,a VLAN name for and an address for when entering the command. DO NOT TYPE THE ANGLE BRACKETS. square brackets [ ] Encloses a required value or list of required arguments.
PAGE 11
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Insert Toggle on and off. When toggled on, inserts text and shifts previous text to right. Left Arrow Move cursor to left. Right Arrow Move cursor to right Tab Help user to select appropriate token. P Display the previous page. N or Space Display the next page. CTRL+C Escape from displayed pages. ESC Escape from displayed pages. Q Escape from displayed pages.
PAGE 12
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 2 Basic Command List show session show serial_port config serial_port {baud_rate [9600 | 19200 | 38400 | 115200] | auto_logout [never | 2_minutes | 5_minutes | 10_minutes | 15_minutes]} enable clipaging disable clipaging login logout ? clear show command_history config command_history config greeting_message {default} show greeting_message config command_prompt [ | username | default] config t
PAGE 13
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide ID Live Time From Level Name --- ------------ --------------------------------------- ----- --------------0 00:01:46.360 10.90.90.10 puser puser 8 00:05:49.340 Serial Port admin admin Total Entries: 2 CTRL+C ESC q Quit SPACE n Next Page p Previous Page r Refresh 2-2 show serial_port Description This command is used to display the current serial port settings. Format show serial_port Parameters None. Restrictions None.
PAGE 14
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config serial_port {baud_rate [9600 | 19200 | 38400 | 115200] | auto_logout [never | 2_minutes | 5_minutes | 10_minutes | 15_minutes]} Parameters baud_rate - (Optional) The serial bit rate that will be used to communicate with the management host. The default baud rate is 115200. 9600 - Specify the serial bit rate to be 9600. 19200 - Specify the serial bit rate to be 19200.
PAGE 15
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To enable pausing of the screen display when show command output reaches the end of the page: :admin#enable clipaging Command: enable clipaging Success. :admin# 2-5 disable clipaging Description This command is used to disable the pausing of the screen display when the show command output reaches the end of the page. The default setting is enabled. Format disable clipaging Parameters None.
PAGE 16
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions None. Example To login the Switch with a user name dlink: :admin#login Command: login UserName:dlink PassWord:**** :admin# 2-7 logout Description This command is used to logout the facility. Format logout Parameters None. Restrictions None.
PAGE 17
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide :admin#logout Command: logout ********** * Logout * ********** Fast Ethernet Switch Command Line Interface Firmware: Build 4.04.004 Copyright(C) 2012 D-Link Corporation. All rights reserved. UserName: 2-8 ? Description This command is used to display the usage description for all commands or the specific one. Format ? Parameters None. Restrictions None.
PAGE 18
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format clear Parameters None. Restrictions None. Example To clear screen: :admin#clear Command: clear :admin# 2-10 show command_history Description The command is used to display command history. Format show command_history Parameters None. Restrictions None.
PAGE 19
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide :admin#show command_history Command: show command_history ? ping login show serial_port show session ? config bpdu_protection ports ? reset ? create account ? create ipif show the ? :admin# 2-11 config command_history Description This command is used to configure the number of commands that the Switch can recall. The Switch “remembers” upto the last 40 commands you entered.
PAGE 20
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config greeting_message {default} Parameters default - (Optional) Adding this parameter to the “config greeting_message” command will return the greeting message (banner) to its original factory default entry. Restrictions Only Administrator and Operator-level users can issue this command.
PAGE 21
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions Only Administrator and Operator-level users can issue this command. Example To display greeting message: :admin#show greeting_message Command: show greeting_message =============================================================================== = Fast Ethernet Switch Command Line Interface Firmware: Build 4.04.004 Copyright(C) 2012 D-Link Corporation. All rights reserved.
PAGE 22
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To edit the command prompt: :admin#config command_prompt Prompt# Command: config command_prompt Prompt# Success. Prompt#:admin# 2-15 config terminal width Description The command is used to set current terminal width. The usage is described as below: 1. Users login and configure the terminal width to 120, this configuration take effect on this login section.
PAGE 23
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 2-16 show terminal width Description The command is used to display the configuration of current terminal width. Format show terminal width Parameters None. Restrictions None.
PAGE 24
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 10_full - Set port speed to 10_full. 100_half - Set port speed to 100_half. 100_full - Set port speed to 100_full._ 1000_full - 1000_full set port speed to 1000_full. While set port speed to 1000_full,user should specify master or slave mode for 1000 base TX interface, and leave the 1000_full without any master or slave setting for other interface. master - Specify that the port(s) will be set to master.
PAGE 25
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters ports - Specify a range of ports to be displayed. - (Optional) Enter the list of ports to be configured here. description - (Optional) Indicates if port description will be included in the display . err_disabled - (Optional) Indicates if ports are disabled by some reasons will be displayed. details - (Optional) Displays the port details. media_type - (Optional) Displays port transceiver type.
PAGE 26
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 3 802.
PAGE 27
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To create a VLAN with name “v2” and VLAN ID 2: :admin#create vlan v2 tag 2 type 1q_vlan advertisement Command: create vlan v2 tag 2 type 1q_vlan advertisement Success. :admin# 3-2 create vlan vlanid Description This command is used to create more than one VLANs at a time. A unique VLAN name (e.g. VLAN10) will be automatically assigned by the system.
PAGE 28
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format delete vlan Parameters vlan - The VLAN name of the VLAN to be deleted. - Enter the VLAN name here. This name can be up to 32 characters long. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To remove a vlan v1: :admin#delete vlan v1 Command: delete vlan v1 Success.
PAGE 29
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 3-5 config vlan Description This command is used to configure a VLAN based on the name. Format config vlan {[add [tagged | untagged | forbidden] | delete] | advertisement [enable | disable]}(1) Parameters - Enter the VLAN name you want to add ports to. This name can be up to 32 characters long. add - (Optional) Specify to add tagged, untagged or forbidden ports to the VLAN.
PAGE 30
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters - Enter a list of VLAN IDs to configure. add - (Optional) Specify to add tagged, untagged or forbidden ports to the VLAN. tagged - Specify the additional ports as tagged. untagged - Specify the additional ports as untagged. forbidden - Specify the additional ports as forbidden. delete - (Optional) Specify to delete ports from the VLAN.
PAGE 31
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide acceptable_frame - (Optional) The type of frame will be accepted by the port. There are two types: tagged_only - Only tagged packets can be accepted by this port. admit_all - All packets can be accepted. pvid - (Optional) Specify the PVID of the ports. - Enter the VLAN ID here. The VLAN ID value must be between 1 and 4094. Restrictions Only Administrator and Operator-level users can issue this command.
PAGE 32
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show vlan Command: show vlan VLAN Trunk State : Enabled VLAN Trunk Member Ports : 1-5 VID : 1 VLAN Type : Static Member Ports : 1-28 Static Ports : 1-28 Current Tagged Ports : Current Untagged Ports: 1-28 Static Tagged Ports : Static Untagged Ports : 1-28 Forbidden Ports : VLAN Name : default Advertisement : Enabled VID : 2 VLAN Name : v2 VLAN Type : Static Advertisement : Enabled Member Ports : 4-8 St
PAGE 33
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show vlan ports 6 Command: show vlan ports 6 Port ----6 6 VID ---1 2 Untagged -------X - Tagged -----X Dynamic ------- Forbidden --------- DES-3200-28/ME:admin# 3-10 show vlan vlanid Description This command is used to display the vlan information using the VLAN ID. Format show vlan vlanid Parameters - Enter the VLAN ID to be displayed. Restrictions None.
PAGE 34
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 3-11 show port_vlan Description This command is used to display the ports’ VLAN attributes on the Switch. Format show port_vlan {} Parameters - (Optional) Specify a range of ports to be displayed. If no parameter specified, system will display all ports gvrp information. Restrictions None. Example To display 802.
PAGE 35
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 3-12 enable pvid auto assign Description This command is used to enable the auto-assignment of PVID. If “Auto-assign PVID” is enabled, PVID will be possibly changed by PVID or VLAN configuration. When user configures a port to VLAN X’s untagged membership, this port’s PVID will be updated with VLAN X. In the form of VLAN list command, PVID is updated with last item of VLAN list.
PAGE 36
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To disable the auto-assign PVID: DES-3200-28/ME:admin#disable pvid auto_assign Command: disable pvid auto_assign Success. DES-3200-28/ME:admin# 3-14 show pvid auto_assign Description This command is used to display the PVID auto-assignment state. Format show pvid auto_assign Parameters None. Restrictions None.
PAGE 37
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config gvrp [timer {join < value 100-100000> | leave < value 100-100000> | leaveall } | nni_bpdu_addr [dot1d | dot1ad]] Parameters timer - Specify that the GVRP timer parameter will be configured. join - (Optional) Specify the Join time will be set. - Enter the time used here. This value must be between 100 and 100000. leave - (Optional) Specify the Leave time will be set.
PAGE 38
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions None. Example To display the global setting of GVRP: DES-3200-28/ME:admin#show gvrp Command: show gvrp Global GVRP : Disabled Join Time : 200 Milliseconds Leave Time : 600 Milliseconds LeaveAll Time : 10000 Milliseconds NNI BPDU Address: dot1d DES-3200-28/ME:admin# 3-17 enable gvrp Description This commands is used to enable the Generic VLAN Registration Protocol (GVRP). Format enable gvrp Parameters None.
PAGE 39
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format disable gvrp Parameters None. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To disable the Generic VLAN Registration Protocol (GVRP): DES-3200-28/ME:admin#disable gvrp Command: disable gvrp Success.
PAGE 40
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 4 802.1X Command List enable 802.1x disable 802.1x create 802.1x user delete 802.1x user show 802.1x user config 802.1x auth_protocol [local | radius_eap] config 802.1x fwd_pdu system [enable | disable] config 802.1x fwd_pdu ports [ | all] [enable | disable] config 802.1x authorization attributes radius [enable | disable] show 802.
PAGE 41
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example Used to enable the 802.1X function: DES-3200-28/ME:admin#enable 802.1x Command: enable 802.1x Success. DES-3200-28/ME:admin# 4-2 disable 802.1x Description This command is used to disable the 802.1X function. Format disable 802.1x Parameters None.
PAGE 42
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 4-3 create 802.1x user Description This command is used to create an 802.1X user. Format create 802.1x user Parameters - Enter the username to be added. This value can be up to 15 characters long. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To create a 802.1x user “test”: DES-3200-28/ME:admin#create 802.1x user test Command: create 802.
PAGE 43
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#delete 802.1x user test Command: delete 802.1x user test Success. DES-3200-28/ME:admin# 4-5 show 802.1x user Description This command is used to display the 802.1X user. Format show 802.1x user Parameters None. Restrictions None. Example To display the 802.1X user information: DES-3200-28/ME:admin#show 802.1x user Command: show 802.
PAGE 44
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters local - Specify the authentication protocol as local. radius_eap - Specify the authentication protocol as RADIUS EAP. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To configure the 802.1X authentication protocol to RADIUS EAP: DES-3200-28/ME:admin#config 802.1x auth_protocol radius_eap Command: config 802.1x auth_protocol radius_eap Success.
PAGE 45
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config 802.1x fwd_pdu system enable Command: config 802.1x fwd_pdu system enable Success. DES-3200-28/ME:admin# 4-8 config 802.1x fwd_pdu ports Description This command is used to control the forwarding of EAPOL PDU. When 802.1X functionality is disabled globally or for a port, and if 802.
PAGE 46
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config 802.1x authorization attributes radius [enable | disable] Parameters radius - If specified to enable, the authorization attributes (for example VLAN, 802.1p default priority, and ACL) assigned by the RADUIS server will be accepted. The default state is enabled. enable - Specify to enable the authorization attributes. disable - Specify to disable the authorization attributes.
PAGE 47
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide :admin#show 802.1x auth_configuration ports 1 Command: show 802.
PAGE 48
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure the port capability: :admin#config 802.1x capability ports 1-10 authenticator Command: config 802.1x capability ports 1-10 authenticator Success. :admin# 4-12 config 802.1x max_users Description This command is used to limit the maximum number of users that can be learned via 802.1X authentication. In addition to the global limitation, maximum user for per port is also limited.
PAGE 49
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config 802.
PAGE 50
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To configure the parameters that control the operation of the authenticator associated with a port: DES-3200-28/ME:admin#config 802.1x auth_parameter ports 1-20 direction both Command: config 802.1x auth_parameter ports 1-20 direction both Success. DES-3200-28/ME:admin# 4-14 config 802.
PAGE 51
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config 802.1x init [port_based ports [ | all] | mac_based ports [ | all] {mac_address }] Parameters port_based ports- Configure the authentication as port based mode. - Enter the list of ports used for the configuration here. all - Specify that all ports will be used. mac_based ports - Configure the authentication as MAC based mode.
PAGE 52
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To re-authenticate the device connected to the port: DES-3200-28/ME:admin#config 802.1x reauth port_based ports all Command: config 802.1x reauth port_based ports all Success. DES-3200-28/ME:admin# 4-17 create 802.1x guest_vlan Description This command is used to assign a static VLAN to be guest VLAN.
PAGE 53
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format delete 802.1x guest_vlan {} Parameters - (Optional) Enter the VLAN name here. The VLAN name can be up to 32 characters long. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To delete the guest VLAN named “guestVLAN”: DES-3200-28/ME:admin#delete 802.1x guest_vlan guestVLAN Command: delete 802.1x guest_vlan guestVLAN Success.
PAGE 54
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config 802.1x guest_vlan ports 2-8 state enable Command: config 802.1x guest_vlan ports 2-8 state enable Warning, The ports are moved to Guest VLAN. Success. DES-3200-28/ME:admin# 4-20 show 802.1x guest_vlan Description This command is used to show the information of guest VLANs. Format show 802.1x guest_vlan Parameters None. Restrictions None. Example To show 802.
PAGE 55
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config radius add key [default | {auth_port | acct_port | timeout | retransmit }] Parameters - Enter the RADIUS server index. This value must be between 1 and 3. - Enter the IP address of the RADIUS server here.
PAGE 56
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters - Specify to delete a RADIUS server.Enter the RADIUS server index. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To delete a radius server: DES-3200-28/ME:admin#config radius delete 1 Command: config radius delete 1 Success. DES-3200-28/ME:admin# 4-23 config radius Description This command is used to configure a RADIUS server.
PAGE 57
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide retransmit - (Optional) The count for re-transmitting. The default value is 2. - Enter the re-transmit value here. This value must be between 1 and 20. default - Specify that the default re-transmit value will be used. Restrictions Only Administrator, Operator and Power-User level users can issue this command.
PAGE 58
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show radius Command: show radius Index ----1 IP Address Auth-Port Acct-Port Timeout Retransmit Key (sec) --------------- --------- --------- ------- ---------- ---------------10.48.74.121 60 1813 5 2 dlink Total Entries : 1 DES-3200-28/ME:admin# 4-25 show auth_statistics Description This command is used to display information of authenticator statistics.
PAGE 59
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show auth_statistics ports 1 Command: show auth_statistics ports 1 Port Number : 1 EapolFramesRx EapolFramesTx EapolStartFramesRx EapolReqIdFramesTx EapolLogoffFramesRx EapolReqFramesTx EapolRespIdFramesRx EapolRespFramesRx InvalidEapolFramesRx EapLengthErrorFramesRx 0 9 0 6 0 0 0 0 0 0 LastEapolFrameVersion LastEapolFrameSource 0 00-00-00-00-00-00 CTRL+C ESC q Quit SPACE n Next Page p Previous Page r
PAGE 60
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show auth_diagnostics ports 1 Command: show auth_diagnostics ports 1 Port Number : 1 EntersConnecting EapLogoffsWhileConnecting EntersAuthenticating SuccessWhileAuthenticating TimeoutsWhileAuthenticating FailWhileAuthenticating ReauthsWhileAuthenticating EapStartsWhileAuthenticating EapLogoffWhileAuthenticating ReauthsWhileAuthenticated EapStartsWhileAuthenticated EapLogoffWhileAuthenticated BackendRespon
PAGE 61
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show auth_session_statistics ports 1 Command: show auth_session_statistics ports 1 Port Number : 1 SessionOctetsRx SessionOctetsTx SessionFramesRx SessionFramesTx SessionId SessionAuthenticMethod SessionTime SessionTerminateCause SessionUserName 0 0 0 0 Remote Authentication Server 0 SupplicantLogoff CTRL+C ESC q Quit SPACE n Next Page p Previous Page r Refresh 4-28 show auth_client Description This c
PAGE 62
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show auth_client Command: show auth_client radiusAuthClient ==> radiusAuthClientInvalidServerAddresses radiusAuthClientIdentifier 0 radiusAuthServerEntry ==> radiusAuthServerIndex :1 radiusAuthServerAddress radiusAuthClientServerPortNumber radiusAuthClientRoundTripTime radiusAuthClientAccessRequests radiusAuthClientAccessRetransmissions radiusAuthClientAccessAccepts radiusAuthClientAccessRejects radiusAu
PAGE 63
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show acct_client Command: show acct_client radiusAcctClient ==> radiusAcctClientInvalidServerAddresses radiusAcctClientIdentifier 0 radiusAuthServerEntry ==> radiusAccServerIndex : 1 radiusAccServerAddress radiusAccClientServerPortNumber radiusAccClientRoundTripTime radiusAccClientRequests radiusAccClientRetransmissions radiusAccClientResponses radiusAccClientMalformedResponses radiusAccClientBadAuthenti
PAGE 64
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example Enable it to configure accounting shell state: DES-3200-28/ME:admin#config accounting service shell state enable Command: config accounting service shell state enable Success. DES-3200-28/ME:admin# 4-31 show accounting service Description This command is used to show the status of RADIUS accounting services. Format show accounting service Parameters None. Restrictions None.
PAGE 65
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 5 Access Authentication Control Command List enable password encryption disable password encryption enable authen_policy disable authen_policy show authen_policy create authen_login method_list_name config authen_login [default | method_list_name ] method {tacacs | xtacacs | tacacs+ | radius | server_group | local | none} delete authen_login method_list_name show authen_
PAGE 66
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions Only Administrator-level users can issue this command. Example To enable the password encryption: DES-3200-28/ME:admin#enable password encryption Command: enable password encryption Success. DES-3200-28/ME:admin# 5-2 disable password encryption Description This command is used to disable password encryption.
PAGE 67
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 5-3 enable authen_policy Description This command is used to enable system access authentication policy. Enable system access authentication policy. When authentication is enabled, the device will adopt the login authentication method list to authenticate the user for login, and adopt the enable authentication method list to authenticate the enable password for promoting the user‘s privilege to Admin level.
PAGE 68
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator-level users can issue this command. Example To disable system access authentication policy: DES-3200-28/ME:admin#disable authen_policy Command: disable authen_policy Success. DES-3200-28/ME:admin# 5-5 show authen_policy Description This command is used to display that system access authentication policy is enabled or disabled. Format show authen_policy Parameters None.
PAGE 69
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format create authen_login method_list_name Parameters - The user-defined method list name. This value can be up to 15 characters long. Restrictions Only Administrator-level users can issue this command. Example To create a user-defined method list for user login: DES-3200-28/ME:admin#create authen_login method_list_name login_list_1 Command: create authen_login method_list_name login_list_1 Success.
PAGE 70
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide tacacs+ - (Optional) Authentication by the built-in server group “tacacs+”. radius - (Optional) Authentication by the built-in server group “radius”. server_group - (Optional) Authentication by the user-defined server group. - Enter the server group value here. This value can be up 15 characters long. local - (Optional) Authentication by local user account database in device. none - (Optional) No authentication.
PAGE 71
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 5-9 show authen_login Description This command is used to display the method list of authentication methods for user login. Format show authen_login [default | method_list_name | all] Parameters default - Display default user-defined method list for user login. method_list_name - Display the specific user-defined method list for user login. - Enter the method list name here.
PAGE 72
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator-level users can issue this command. Example To create a user-defined method list for promoting user's privilege to Admin level: DES-3200-28/ME:admin#create authen_enable method_list_name enable_list_1 Command: create authen_enable method_list_name enable_list_1 Success.
PAGE 73
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure a user-defined method list for promoting user's privilege to Admin level: DES-3200-28/ME:admin#config authen_enable method_list_name enable_list_1 method tacacs+ tacacs local_enable Command: config authen_ enable method_list_name enable_list_1 method tacacs+ tacacs local_enable Success.
PAGE 74
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters default - Display default user-defined method list for promoting user's privilege to Admin level. method_list_name - Display the specific user-defined method list for promoting user's privilege to Admin level. - Enter the method list name here. This value can be up to 15 characters long. all - Display all method lists for promoting user's privilege to Admin level.
PAGE 75
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator-level users can issue this command. Example To configure the login method list for telnet: DES-3200-28/ME:admin#config authen application telnet login method_list_name login_list_1 Command: config authen application telnet login method_list_name login_list_1 Success.
PAGE 76
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 5-16 create authen server_group Description This command is used to create a user-defined authentication server group. The maximum supported number of server groups including built-in server groups is 8. Each group consists of 8 server hosts as maximum. Format create authen server_group Parameters - The user-defined server group name. This value can be up to 15 characters long.
PAGE 77
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide add - Add a server host to a server group. delete - Remove a server host from a server group. server_host - Server host’s IP address. - Enter the server host IP address here. protocol - Specify the authentication protocol used. tacacs - Specify that the TACACS authentication protocol will be used. xtacacs - Specify that the XTACACS authentication protocol will be used.
PAGE 78
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#delete authen server_group mix_1 Command: delete authen server_group mix_1 Success. DES-3200-28/ME:admin# 5-19 show authen server_group Description This command is used to display the authentication server groups. Format show authen server_group {} Parameters - (Optional) The built-in or user-defined server group name. This value can be up to 15 characters long.
PAGE 79
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide services can be run on the same physical host. The maximum supported number of server hosts is 16. Format create authen server_host protocol [tacacs | xtacacs | tacacs+ | radius] {port | key [ | none] | timeout | retransmit } Parameters - Enter the server host IP address. protocol - Specify the host's authentication protocol.
PAGE 80
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 5-21 config authen server_host Description This command is used to configure an authentication server host. Format config authen server_host protocol [tacacs | xtacacs | tacacs+ | radius] {port | key [ | none ] | timeout | retransmit } Parameters - Enter the server host IP address. protocol - Specify the server host's authentication protocol.
PAGE 81
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format delete authen server_host protocol [tacacs | xtacacs | tacacs+ | radius] Parameters - Enter the server host's IP address. protocol - Specify that server host's authentication protocol. tacacs - Server host’s authentication protocol. xtacacs - Server host’s authentication protocol. tacacs+ - Server host’s authentication protocol. radius - Server host’s authentication protocol.
PAGE 82
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show authen server_host Command: show authen server_host IP Address --------------10.1.1.222 Protocol -------TACACS+ Port ----15555 Timeout ------10 Retransmit --------------- Key ------------------------This is a secret.
PAGE 83
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters - The amount of attempts for user's trying to login or promote the privilege on console or telnet or SSH. This value must be between 1 and 255. Default value is 3. Restrictions Only Administrator-level users can issue this command.
PAGE 84
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 5-27 enable admin Description This command is used to enter the administrator level privilege. Promote the "user" privilege level to "admin" level. When the user enters this command, the authentication method tacacs, xtacacs, tacacs+, user-defined server groups, local_enable or none will be used to authenticate the user.
PAGE 85
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters encrypt - (Optional) Specify the password form. plain_text - Specify the password in plain text form. sha_1 - Specify the password in SHA-1 encrypted form. - (Optional) The password for promoting the privilege level. The length for a password in plain-text form and SHA-1 encrypted form are different. plain-text: Passwords can be from a minimum of 0 to a maximum of 15 characters.
PAGE 86
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 6 Access Control List (ACL) Command List create access_profile profile_id profile_name [ethernet {vlan {} | source_mac | destination_mac | 802.
PAGE 87
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide hh:mm:ss> weekdays | delete] show time_range show current_config access_profile 6-1 create access_profile Description This command is used to create access control list profiles. When creating ACL, each profile can have 256 rules/access IDs. However, when creating ACL type as Ethernet or IPv4 at the first time, 62 rules are reserved for the system. In this case, only 194 rules are available to configure.
PAGE 88
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide flowlabel | source_ipv6_mask | destination_ipv6_mask | [tcp {src_port_mask | dst_port_mask } | udp {src_port_mask | dst_port_mask } | icmp {type | code}]}] Parameters profile_id - Specify the index of the access list profile. - Enter the profile ID here. This value must be between 1 and 4.
PAGE 89
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide - Enter the offset chunk 1 value here. This value must be between 0 and 31. - Enter the offset chunk 1 mask here. offset_chunk_2 - (Optional) Specify that the offset chunk 2 will be used. - Enter the offset chunk 2 value here. This value must be between 0 and 31. - Enter the offset chunk 2 mask here.
PAGE 90
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#create access_profile profile_id 1 profile_name t1 ethernet vlan source_mac 00-00-00-00-00-01 destination_mac 00-00-00-00-00-02 802.1p ethernet_type Command: create access_profile profile_id 1 profile_name 1 ethernet vlan source_mac 00-00-00-00-00-01 destination_mac 00-00-00-00-00-02 802.1p ethernet_type Success.
PAGE 91
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#delete access_profile profile_id 1 Command: delete access_profile profile_id 1 Success. DES-3200-28/ME:admin# 6-3 config access_profile Description This command is used to configure an access list entry. The ACL mirror function works after the mirror has been enabled and the mirror port has been configured using the mirror command.
PAGE 92
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide auto_assign - Specify that the access ID will automatically be assigned. - Enter the access ID used here. This value must be between 1 and 256. ethernet - Specify to configure the ethernet access profile. vlan - (Optional) Specify the VLAN name. - Enter the name of the VLAN here. This name can be up to 32 characters long. vlan_id - (Optional) Specify the VLAN ID used.
PAGE 93
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide mask - (Optional) Specify an additional mask parameter that can be configured. - Enter the destination port mask here. flag - (Optional) Specify the TCP flag fields. all - Specify that all the TCP flags will be used in this configuration. urg - (Optional) Specify that the TCP flag field will be set to 'urg'. ack - (Optional) Specify that the TCP flag field will be set to 'ack'.
PAGE 94
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide - Enter the TCP source port mask value here. dst_port - (Optional) Specify the value of the IPv6 Layer 4 TCP destination port. - Enter the TCP destination port value here. This value must be between 0 and 65535. mask - Specify an additional mask parameter that can be configured. - Enter the TCP destination port mask value here.
PAGE 95
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide delete - Specify that a profile or a rule will be deleted. access_id - Specify the index of the access list entry. The value range is 1-256, but the supported maximum number of entries depends on the project. - Enter the access ID used here. This value must be between 1 and 256. Restrictions Only Administrator, Operator and Power-User level users can issue this command.
PAGE 96
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Total Used HW Entries Total Available HW Entries : 128 : 896 ============================================================================== Profile ID: 1 Profile name: EtherACL Type: Ethernet MASK on VLAN 802.1p Ethernet Type : 0xFFF Available HW Entries : 193 -----------------------------------------------------------------------------Rule ID : 1 Ports: 1 Match on VLAN ID 802.
PAGE 97
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Available HW Entries : 255 -----------------------------------------------------------------------------Rule ID : 1 Ports: 3 Match on Class : 0 Action: Permit ============================================================================== ============================================================================== Profile ID: 4 Profile name: PCACL Type: User Defined MASK on offset_chunk_1 offset_chunk_2 offset_chunk_3 offse
PAGE 98
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Rule ID : 22 Ports: 1-7 Match on VLAN ID : 8 Source MAC : 00-01-02-03-04-05 Destination MAC :00-05-04-03-02-00 Action: Deny Mask : 0xFFF Mask : FF-FF-FF-FF-FF-FF Mask : FF-FF-FF-FF-FF-00 DES-3200-28/ME:admin# The following example displays the packet content mask profile for the profile with an ID of 4: DES-3200-28/ME:admin#show access_profile profile_id 4 Command: show access_profile profile_id 4 Access Profile Table Prof
PAGE 99
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide For single rate three color mode, users need to specify the committed rate, in Kbps, the committed burst size, and the excess burst size. For the two rate three color mode, users need to specify the committed rate in Kbps, the committed burst size, the peak rate and the peak burst size. There are two cases for mapping the color of a packet: Color-blind mode and Color-aware mode.
PAGE 100
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide cir - Specify the Committed Information Rate. The unit is in Kbps. CIR should always be equal or less than PIR. - Enter the commited information rate value here. This value must be between 1 and 1048576. cbs - (Optional) Specify the “Committed Burst Size”. The unit is Kbytes. That is to say, 1 means 1Kbytes. This parameter is an optional parameter. The default value is 4*1024.
PAGE 101
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure a “two rate, three color” flow meter: DES-3200-28/ME:admin#config flow_meter profile_id 1 access_id 1 tr_tcm cir 1000 cbs 2000 pir 2000 pbs 2000 color_blind conform permit counter enable exceed permit replace_dscp 60 counter enable violate drop Command: config flow_meter profile_id 1 access_id 1 tr_tcm cir 1000 cbs 2000 pir 2000 pbs 2000 color_blind conform permit counter enable exceed permit replace_dscp
PAGE 102
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show flow_meter Command: show flow_meter Flow Meter Information -----------------------------------------------------------------------------Profile ID:1 Aceess ID:1 Mode : trTCM / ColorBlind CIR(Kbps):1000 CBS(Kbyte):2000 PIR(Kbps):2000 PBS(Kbyte):2000 Action: Conform : Permit Counter: Enabled Exceed : Permit Replace DSCP: 60 Counter: Enabled Violate : Drop Counter: Disabled ------------------------------
PAGE 103
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure a time range named “1” that starts every Monday at 01:01:01am and ends at 02:02:02am: DES-3200-28/ME:admin#config time_range 1 hours start_time 1:1:1 end_time 2:2:2 weekdays mon Command: config time_range 1 hours start_time 1:1:1 end_time 2:2:2 weekdays mon Success. DES-3200-28P:admin#config time_range 1 delete Command: config time_range 1 delete Success.
PAGE 104
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show time_range Command: show time_range Time Range Information ----------------------------Range Name : 1 Weekdays : Mon Start Time : 01:01:01 End Time : 02:01:01 Total Entries :1 DES-3200-28/ME:admin# 6-9 show current_config access_profile Description This command is used to display the ACL part of the current configuration, when logged in with user level privileges.
PAGE 105
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show current_config access_profile Command: show current_config access_profile #------------------------------------------------------------------# ACL create access_profile ethernet vlan profile_id 1 config access_profile profile_id 1 add access_id 1 ethernet vlan default port 1 permit create access_profile ip source_ip_mask 255.255.255.
PAGE 106
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 7 Address Resolution Protocol (ARP) Command List create arpentry delete arpentry [ | all] config arpentry config arp_aging time clear arptable show arpentry {ipif | ipaddress | static | mac_address } 7-1 create arpentry Description This command is used to enter a static ARP entry into the Switch’s ARP table.
PAGE 107
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format delete arpentry [ | all] Parameters - The IP address of the end node or station. all - Delete all ARP entries. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To delete an entry of IP address 10.48.74.121 from the ARP table: DES-3200-28/ME:admin#delete arpentry 10.48.74.121 Command: delete arpentry 10.48.74.121 Success.
PAGE 108
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config arpentry 10.48.74.121 00-50-BA-00-07-37 Command: config arpentry 10.48.74.121 00-50-BA-00-07-37 Success. DES-3200-28/ME:admin# 7-4 config arp_aging time Description This command is used to set the maximum amount of time, in minutes, that a dynamic ARP entry can remain in the Switch’s ARP table, without being accessed, before it is dropped from the table.
PAGE 109
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To clear the ARP table: DES-3200-28/ME:admin#clear arptable Command: clear arptable Success. DES-3200-28/ME:admin# 7-6 show arpentry Description This command is used to displays the ARP table. You can filter the display by IP address, MAC address, Interface name, or static entries.
PAGE 110
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show arpentry Command: show arpentry ARP Aging Time : 20 Interface ------------System System System System System System IP Address --------------10.0.0.0 10.1.1.1 10.1.1.2 10.1.1.3 10.90.90.90 10.255.255.
PAGE 111
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 8 ARP Spoofing Prevention Command List config arp_spoofing_prevention [add gateway_ip gateway_mac ports [ | all] | delete gateway_ip ] show arp_spoofing_prevention 8-1 config arp_spoofing_prevention Description This command is used to configure the spoofing prevention entry to prevent spoofing of MAC for the protected gateway.
PAGE 112
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config arp_spoofing_prevention add gateway_ip 10.254.254.251 gateway_mac 00-00-00-11-11-11 ports 1-2 Command: config arp_spoofing_prevention add gateway_ip 10.254.254.251 gateway_ma c 00-00-00-11-11-11 ports 1-2 Success. DES-3200-28/ME:admin# 8-2 show arp_spoofing_prevention Description This command is used to show the ARP spoofing prevention entry. Format show arp_spoofing_prevention Parameters None.
PAGE 113
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 9 Auto-Configuration Command List enable autoconfig disable autoconfig show autoconfig config autoconfig timeout 9-1 enable autoconfig Description This command is used to enable auto configuration. When enabled, during power on initialization, the Switch will get configure file path name and TFTP server IP address from the DHCP server.
PAGE 114
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format disable autoconfig Parameters None. Restrictions Only Administrator and Operator-level users can issue this command. Example To disable autoconfig: DES-3200-28/ME:admin#disable autoconfig Command: disable autoconfig Success. DES-3200-28/ME:admin# 9-3 show autoconfig Description This command is used to display if the auto-configuration is enabled or disabled. Format show autoconfig Parameters None.
PAGE 115
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 9-4 config autoconfig timeout Description This command is used to configure the timeout value. This timer is used to limit the length of time in getting configuration settings from the network. When timeout occurs, the auto configuration operation will be stopped and the local configuration file will be used to configure the system.
PAGE 116
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 10 Basic Commands Command List create account [admin | operator | power_user | user] {encrypt [plain_text | sha_1] } config account {encrypt [plain_text | sha_1] } show account delete account show switch enable telnet {} disable telnet enable web {} disable web reboot {force_agree} reset {[config | system]} {forc
PAGE 117
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide sha_1 - Select to specify the password in the SHA-I encrypted form. - The password for the user account. The length for of password in plain-text form and in encrypted form are different. For the plain-text form, passwords must have a minimum of 0 character and can have a maximum of 15 characters. For the encrypted form password, the length is fixed to 35 bytes long. The password is case-sensitive.
PAGE 118
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters - Enter the user name of the account that has been defined. encrypt - (Optional) Specify that the password will be encrypted. plain_text - Select to specify the password in plain text form. sha_1 - Select to specify the password in the SHA-I enacrpted form. - The password for the user account. The length for of password in plain-text form and in encrypted form are different.
PAGE 119
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator-level users can issue this command. Example To display the accounts that have been created: DES-3200-28/ME:admin#show account Command: show account Current Accounts: Username --------------admin oper power user Access Level -----------Admin Operator Power_user User Total Entries : 4 DES-3200-28/ME:admin# 10-4 delete account Description This command is used to delete an existing account.
PAGE 120
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 10-5 show switch Description This command is used to display the Switch information. Format show switch Parameters None. Restrictions None. Example The following is an example for display of the Switch information. DES-3200-28/ME:admin#show switch Command: show switch Device Type : DES-3200-28P Fast Ethernet Switch MAC Address : B8-A3-86-CF-1F-20 IP Address : 10.90.90.90 (Manual) VLAN Name : default Subnet Mask : 255.0.
PAGE 121
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 10-6 enable telnet Description This command is used to enable TELNET and configure port number. Format enable telnet {} Parameters - (Optional) The TCP port number. TCP ports are numbered between 1 and 65535. The “well-known” TCP port for the TELNET protocol is 23. Restrictions Only Administrator and Operator-level users can issue this command.
PAGE 122
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#disable telnet Command: disable telnet Success. DES-3200-28/ME:admin# 10-8 enable web Description This command is used to enable HTTP and configure port number. Format enable web {} Parameters - (Optional) The TCP port number. TCP ports are numbered between 1 and 65535. The “well-known” TCP port for the WEB protocol is 80.
PAGE 123
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator and Operator-level users can issue this command. Example To disable HTTP: DES-3200-28/ME:admin#disable web Command: disable web Success. DES-3200-28/ME:admin# 10-10 reboot Description This command is used to restart the Switch.
PAGE 124
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format reset {[config | system]} {force_agree} Parameters config - (Optional) If you specify the ‘config’ keyword , all parameters are reset to default settings. But device will not do save neither reboot. system - (Optional) If you specify the ‘system’ keyword, all parameters are reset to default settings. Then the Switch will do factory reset, save and reboot.
PAGE 125
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator level can issue this command. Example To configure c:/DES3200_Run_4_00_014.had as the boot up image: DES-3200-28/ME:admin#config firmware image c:/DES3200_Run_4_02_004.had boot_up Command: config firmware image c:/DES3200_Run_4_02_004.had boot_up Success. DES-3200-28/ME:admin# 10-13 create ipif Description This command is used to create an IP interface.
PAGE 126
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 10-14 config ipif Description This command is used to configure the IP interface.
PAGE 127
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To configure an interface’s IPv4 network address: DES-3200-28/ME:admin#config ipif System ipaddress 192.168.69.123/24 vlan default Command: config ipif System ipaddress 192.168.69.123/24 vlan default Success. DES-3200-28/ME:admin# 10-15 delete ipif Description This command is used to delete an IP interface.
PAGE 128
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 10-16 enable ipif Description This commands is used to enable the IP interface. Format enable ipif [ | all] Parameters ipif_name - Specify the name of the IP interface. - Enter the IP interface name used here. This name can be up to 12 characters long. all – Specify that all the IP interfaces will be enabled.
PAGE 129
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To disable an IP interface: DES-3200-28/ME:admin#disable ipif newone Command: disable ipif newone Success. DES-3200-28/ME:admin# 10-18 show ipif Description This command is used to display an IP interface. Format show ipif {} Parameters ipif_name - Specify the name of the IP interface. - (Optional) Enter the IP interface name used here. This name can be up to 12 characters long.
PAGE 130
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 10-19 enable ipif_ipv6_link_local_auto Description This command is used to enable the auto configuration of link local address when there are no IPv6 addresses explicitly configured. When an IPv6 address is explicitly configured, the link local address will be automatically configured, and the IPv6 processing will be started.
PAGE 131
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To disable the IP interface for IPv6 link local automatic: DES-3200-28/ME:admin#disable ipif_ipv6_link_local_auto newone Command: disable ipif_ipv6_link_local_auto newone Success.
PAGE 132
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 11 BPDU Attack Protection Command List config bpdu_protection ports [ | all ] {state [enable | disable] | mode [ drop | block | shutdown} (1) config bpdu_protection recovery_timer [ | infinite] config bpdu_protection [trap | log] [none | attack_detected | attack_cleared | both] enable bpdu_protection disable bpdu_protection show bpdu_protection {ports {}} 11-1 config bpdu_protect
PAGE 133
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To set the port state enable and drop mode: DES-3200-28/ME:admin#config bpdu_protection ports 1 state enable mode drop Commands: config bpdu_protection ports 1 state enable mode drop Success. DES-3200-28/ME:admin# 11-2 config bpdu_protection recovery_interval Description This command is used to configure BPDU protection recovery timer.
PAGE 134
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config bpdu_protection [trap | log] [none | attack_detected | attack_cleared | both] Parameters trap - To specify the trap state. log - To specify the log state. none - Neither attack_detected nor attack_cleared is trapped or logged. attack_detected - Events will be logged or trapped when the BPDU attacks is detected. attack_cleared - Events will be logged or trapped when the BPDU attacks is cleared.
PAGE 135
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#enable bpdu_protection Commands: enable bpdu_protection Success. DES-3200-28/ME:admin# 11-5 disable bpdu_protection Description This command is used to disable BPDU protection function globally for the Switch. Format disable bpdu_protection Parameters None. Restrictions Only Administrator, Operator and Power-User level users can issue this command.
PAGE 136
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions None.
PAGE 137
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 12 Cable Diagnostics Command List cable_diag ports [ | all] 12-1 cable_diag ports Description This command is used to configure cable diagnostics on ports. For FE port, two pairs of cable will be diagnosed. For GE port, four pairs of cable will be diagnosed. The following test result can be displayed.  Open - The cable in the error pair does not have a connection at the specified position.
PAGE 138
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide  When the link partner is powered down with errors, this command can detect whether the error is open, short, or crosstalk. In this case this command can also detect the distance of the error  When there is no link partner with no errors and the link is up, this command can detect the cable length  When there is no link partner with errors, this command can detect whether the error is open, short, or crosstalk.
PAGE 139
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example Test the cable on port 1, 11, and 12: DES-3200-28/ME:admin#cable_diag ports 1,11-12 Command: cable_diag ports 1,11-12 Perform Cable Diagnostics ...
PAGE 140
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 13 Command Logging Command List enable command logging disable command logging show command logging 13-1 enable command logging Description This command is used to enable the command logging function. This is disabled by default. Note: When the Switch is under booting procedure, all configuration command should not be logged.
PAGE 141
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions Only Administrator-level users can issue this command. Example To disable the command logging: DES-3200-28/ME:admin#disable command logging Command: disable command logging Success. DES-3200-28/ME:admin# 13-3 show command logging Description This command is used to display the Switch’s general command logging configuration status. Format show command logging Parameters None.
PAGE 142
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 14 Compound Authentication Command List enable authorization attributes disable authorization attributes show authorization config authentication server failover [local | permit | block] show authentication 14-1 enable authorization Description This command is used to enable authorization. Format enable authorization attributes Parameters None.
PAGE 143
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example This example sets authorization global state disabled: DES-3200-28/ME:admin#disable authorization attributes Command: disable authorization attributes Success. DES-3200-28/ME:admin# 14-3 show authorization Description This command is used to display authorization status.
PAGE 144
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config authentication server failover [local | permit | block] Parameters local - Use local DB to authenticate the client. permit - The client is always regarded as authenticated. block - Block the client (Default setting). Restrictions Only Administrator, Operator and Power-User level users can issue this command.
PAGE 145
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show authentication Command: show authentication Authentication Server Failover: Local.
PAGE 146
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 15 Configuration Command List show config [effective | modified | current_config | boot_up | file ] {[include | exclude | begin] { {}} {[include | exclude | begin] { {}} {[include | exclude | begin ] { {}}}}} config configuration
PAGE 147
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide setting regarding STP is not displayed. The lower level setting will only be displayed when the higher level setting is enabled. Note: This parameter is only for the current configuration. modified - Show only the commands which are not default setting. Note:This parameter is only for the current configuration. current_config - Specify the current configuration. boot_up - Specify the list of the bootup configuration.
PAGE 148
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show config modified Command: show config modified #------------------------------------------------------------------------------# DES-3200-28/ME Fast Ethernet Switch # Configuration # # Firmware: Build 4.04.004 # Copyright(C) 2012 D-Link Corporation. All rights reserved.
PAGE 149
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure the Switch’s configuration file as boot up: DES-3200-28/ME:admin#config configuration config.cfg boot_up Command: config configuration config.cfg boot_up Success. DES-3200-28/ME:admin# 15-3 save Description This command is used to save the current configuration to a file. Format save {[config | log | all]} Parameters config - (Optional) Specify to save the configuration to a file.
PAGE 150
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions None. Example To display the boot file: DES-3200-28/ME:admin#show boot_file Command: show boot_file Bootup Firmware Bootup Configuration : /c:/runtime.had : /c:/config.
PAGE 151
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 16 Connectivity Fault Management (CFM) Command List create cfm md {md_index } level config cfm md [ | md_index ] {mip [none | auto | explicit] | sender_id [none | chassis | manage | chassis_manage]} create cfm ma {ma_index } md [ | md_index ] config cfm ma [ | ma_index
PAGE 152
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide clear cfm pkt_cnt {[ports {[rx | tx]} | [rx | tx] | ccm]} 16-1 create cfm md Description This command is used to create a maintenance domain. Format create cfm md {md_index } level Parameters - Enter the maintenance domain name. This name can be up to 22 characters long. md_index - (Optional) Specify the maintenance domain index.
PAGE 153
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters - Enter the maintenance domain name. This name can be up to 22 characters long. md_index - Specify the maintenance domain index. - Enter the maintenance domain index value here. This value must be between 1 and 4294967295. mip - (Optional) This is the control creations of MIPs. none - Do not create MIPs. This is the default value.
PAGE 154
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide md - Specify the maintenance domain name. - Enter the maintenance domain name here. This name can be up to 22 characters long. md_index - Specify the maintenance domain index. - Enter the maintenance domain index value here. This value must be between 1 and 4294967295. Restrictions Only Administrator, Operator and Power-User level users can issue this command.
PAGE 155
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide VLANs. - Enter the VLAN ID used here. This value must be between 1 and 4094. mip - (Optional) This is the control creation of MIPs. none - Specify not to create MIPs. auto - MIPs can always be created on any ports in this MA, if that port is not configured with an MEP of that MA.
PAGE 156
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format create cfm mep mepid md [ | md_index ] ma [ | ma_index ] direction [inward | outward] port Parameters - Enter the MEP name used. It is unique among all MEPs configured on the device.This name can be up to 32 characters long. mepid - Specify the MEP ID. It should be configured in the MA’s MEPID list.
PAGE 157
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide    Some Remote MEPs Down: priority 3 Some Remote MEP MAC Status Errors: priority 2 Some Remote MEP Defect Indications: priority 1 If multiple types of the fault occur on an MEP, only the fault with the highest priority will be alarmed.
PAGE 158
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide alarm_reset_time - (Optional) This is the dormant duration time before a defect is triggered before the fault can be re-alarmed. The unit is centisecond, the range is 250-1000. The default value is 1000. - Enter the alarm reset time value here. This value must be between 250 and 1000 centiseconds. Restrictions Only Administrator, Operator and Power-User level users can issue this command.
PAGE 159
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To delete a CFM MEP: DES-3200-28/ME:admin#delete cfm mep mepname mep1 Command: delete cfm mep mepname mep1 Success. DES-3200-28/ME:admin# 16-8 delete cfm ma Description This command is used to delete a created maintenance association. All MEPs created in the maintenance association will be deleted automatically.
PAGE 160
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 16-9 delete cfm md Description This command is used to delete a previously created maintenance domain. All the MEPs and maintenance associations created in the maintenance domain will be deleted automatically. Format delete cfm md [ | md_index ] Parameters - Enter the maintenance domain name. This name can be up to 22 characters long.
PAGE 161
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To enable the CFM globally: DES-3200-28/ME:admin#enable cfm Command: enable cfm Success. DES-3200-28/ME:admin# 16-11 disable cfm Description This command is used to disable the CFM globally. Format disable cfm Parameters None. Restrictions Only Administrator, Operator and Power-User level users can issue this command.
PAGE 162
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config cfm ports state [enable | disable] Parameters - Enter the list of ports used for this configuration. state - Specify that the the CFM function will be enabled or disabled. enable - Specify that the CFM function will be enabled. disable - Specify that the CFM function will be disabled. Restrictions Only Administrator, Operator and Power-User level users can issue this command.
PAGE 163
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show cfm ports 3-6 Command: show cfm ports 3-6 Port ----3 4 5 6 State -------Enabled Enabled Enabled Disabled DES-3200-28/ME:admin# 16-14 show cfm Description This command is used to show the CFM configuration.
PAGE 164
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide CFM State: Enabled MD Index ---------1 MD Name ---------------------op_domain Level ----2 DES-3200-28/ME:admin#show cfm md op_domain Command: show cfm md op_domain MD Index : MD Name : MD Level : MIP Creation: SenderID TLV: MA Index ---------1 1 op_domain 2 Explicit None MA Name ---------------------op1 VID ---1 DES-3200-28/ME:admin#show cfm md op_domain ma op1 Command: show cfm md op_domain ma op1 MA Index : MA Name :
PAGE 165
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Cross-connect CCMs Error CCMs Normal CCMs Port Status CCMs If Status CCMs CCMs transmitted In-order LBRs Out-of-order LBRs Next LTM Trans ID Unexpected LTRs LBMs Transmitted : : : : : : : : : : : 0 0 0 0 0 0 0 0 0 0 0 received received received received received received received received Remote MEPID MAC Address Status RDI PortSt IfSt Detect Time ------ ----------------- ------ --- ------- ---------- ------------------2 F
PAGE 166
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To show the CFM faults: DES-3200-28/ME:admin#show cfm fault Command: show cfm fault MD Name ----------op_domain MA Name ----------op1 MEPID ----1 Status --------------------------------Cross-connect CCM Received D DES-3200-28/ME:admin# 16-16 show cfm port Description This command is used to show MEPs and MIPs created on a port.
PAGE 167
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 16-17 cfm loopback Description This command is used to start a CFM loopback test. You can press Ctrl+C to exit the loopback test. The MAC address represents the destination MEP or MIP that can be reached by this MAC address. The MEP represents the source MEP to initiate the loopback message.
PAGE 168
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#cfm loopback 32-00-70-89-31-06 mepname mep1 Command: cfm loopback 32-00-70-89-31-06 mepname mep1 Reply Reply Reply Reply from from from from 32-00-70-89-31-06: 32-00-70-89-31-06: 32-00-70-89-31-06: 32-00-70-89-31-06: bytes=0 bytes=0 bytes=0 bytes=0 time=50ms time=50ms time=50ms time=50ms CFM loopback statistics for 32-00-70-89-31-06: Packets: Sent=4, Received=4, Lost=0(0% loss).
PAGE 169
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To transmit an LTM: DES-3200-28/ME:admin#cfm linktrace 00-01-02-03-04-05 mepname mep1 Command: cfm linktrace 00-01-02-03-04-05 mepname mep1 Transaction ID: 26 Success. DES-3200-28/ME:admin# 16-19 show cfm linktrace Description This command is used to show the link trace responses. The maximum link trace responses a device can hold is 128.
PAGE 170
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show cfm linktrace mepname mep1 trans_id 26 Command: show cfm linktrace mepname mep1 trans_id 26 Transaction ID: 26 From MEP mep1 to 32-00-70-89-31-06 Start Time : 2011-11-22 16:05:08 Hop --1 2 3 MEPID ----2 Ingress MAC Address ------------------00-00-00-00-00-00 00-32-28-40-09-07 00-00-00-00-00-00 Egress MAC Address ------------------32-00-70-89-41-06 00-32-28-40-09-05 32-00-70-89-31-06 Forwarded ----
PAGE 171
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide be between 1 and 4294967295. ma - (Optional) Specify the maintenance association name. - Enter the maintenance association name her. This name can be up to 22 characters long. ma_index - Specify the maintenance association index. - Enter the maintenance association index value here. This value must be between 1 and 4294967295. mepid - (Optional) Specify the MEP ID used.
PAGE 172
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show cfm mipccm Command: show cfm mipccm MA ---------opma opma VID ---1 1 MAC Address ----------------xx-xx-xx-xx-xx-xx xx-xx-xx-xx-xx-xx Port ----2 3 Total: 2 DES-3200-28/ME:admin# 16-22 config cfm mp_ltr_all Description This command is used to enable or disable the "all MPs reply LTRs" function.
PAGE 173
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions None. Example To show the configuration of the "all MPs reply LTRs" function: DES-3200-28/ME:admin#show cfm mp_ltr_all Command: show cfm mp_ltr_all All MPs reply LTRs: Disabled DES-3200-28/ME:admin# 16-24 show cfm remote_mep Description This command is used to show remote MEPs.
PAGE 174
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To show the CFM Remote MEP information: DES-3200-28/ME:admin#show cfm remote_mep mepname mep1 remote_mepid 2 Command: show cfm remote_mep mepname mep1 remote_mepid 2 Remote MEPID : MAC Address : Status : RDI : Port State : Interface Status : Last CCM Serial Number : Sender Chassis ID : Sender Management Address: Detect Time : 2 00-11-22-33-44-02 OK Yes Blocked Down 1000 00-11-22-33-44-00 SNMP-UDP-IPv4 10.90.90.
PAGE 175
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide ----------------------------------------------------------------------------Port AllPkt CCM LBR LBM LTR LTM VidDrop OpcoDrop ----- -------- -------- -------- -------- -------- -------- -------- -------all 2446 2434 0 9 0 3 0 0 1 2446 2434 0 9 0 3 0 0 2 0 0 0 0 0 0 0 0 3 0 0 0 0 0 0 0 0 4 0 0 0 0 0 0 0 0 5 0 0 0 0 0 0 0 0 6 0 0 0 0 0 0 0 0 7 0 0 0 0 0 0 0 0 8 0 0 0 0 0 0 0 0 9 0 0 0 0 0 0 0 0 10 0 0 0 0 0 0 0 0 11 0 0 0 0 0 0 0
PAGE 176
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 15 16 17 18 19 20 21 22 23 24 25 26 27 28 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 DES-3200-28/ME:admin#show cfm pkt_cnt ccm Command: show cfm pkt_cnt ccm CCM RX XCON Error Normal counters: = Cross-connect CCMs = Error CCMs = Normal CCMs MEP Name ----------1 28mep VID ---1 45 Port ----1 3 L
PAGE 177
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To clear the CFM packet’s RX/TX counters: DES-3200-28/ME:admin#clear cfm pkt_cnt Command: clear cfm pkt_cnt Success. DES-3200-28P:admin#clear cfm pkt_cnt ccm Command: clear cfm pkt_cnt ccm Success.
PAGE 178
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 17 CPU Interface Filtering Command List create cpu access_profile profile_id [ethernet {vlan | source_mac | destination_mac | 802.
PAGE 179
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide | offset_16-31 | offset_32-47 | offset_48-63 | offset_64-79
PAGE 180
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide and 15. - Enter the mask pattern offset of the frame between 0 and 15 here. offset_16-31 - (Optional) Specify that the mask pattern offset of the frame will be between 16 and 31. - Enter the mask pattern offset of the frame between 16 and 31 here. offset_32-47 - (Optional) Specify that the mask pattern offset of the frame will be between 32 and 47.
PAGE 181
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters profile_id - Specify the index of access list profile. - Enter the profile ID value here. This value must be between 1 and 5. all – Specify that al the access list profiles will be deleted. Restrictions Only Administrator, Operator and Power-User level users can issue this command.
PAGE 182
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide - Enter the access ID here. This value must be between 1 and 100. ethernet - Specify that the profile type will be Ethernet. vlan - (Optional) Specify the VLAN name used. - Enter the name of the VLAN here. This name can be up to 32 characters long. vlan_id - (Optional) Specify the VLAN ID used. - Enter the VLAN ID used here. source_mac - (Optional) Specify the source MAC address.
PAGE 183
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide and 65535. protocol_id - Specify that the rule applies to the value of IP protocol ID traffic. - Enter the protocol ID value here. This value must be between 0 and 255. user_define - (Optional) Specify that the rule applies to the IP protocol ID and the mask options behind the first 4 bytes of the IP payload. - Enter the user-defined IP protocol ID mask here.
PAGE 184
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config cpu access_profile profile_id 1 add access_id 1 ip vlan default source_ip 20.2.2.3 destination_ip 10.1.1.252 dscp 3 icmp type 11 code 32 port 1 deny Command: config cpu access_profile profile_id 1 add access_id 1 ip vlan default source_ip 20.2.2.3 destination_ip 10.1.1.252 dscp 3 icmp type 11 code 32 port 1 deny Success.
PAGE 185
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions Only Administrator and Operator-level users can issue this command. Example To disable cpu_interface_filtering: DES-3200-28/ME:admin#disable cpu_interface_filtering Command: disable cpu_interface_filtering Success. DES-3200-28/ME:admin# 17-6 show cpu access_profile Description This command is used to display current access list table.
PAGE 186
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide = Profile ID: 1 Type: Ethernet MASK on VLAN : 0xFFF Source MAC : 00-00-00-00-00-01 Destination MAC : 00-00-00-00-00-02 802.1p Ethernet Type Unused Rule Entries: 100 =============================================================================== = =============================================================================== = Profile ID: 2 Type: IPv4 MASK on VLAN Source IP Dest IP DSCP ICMP Type Code : 0xFFF : 20.0.0.
PAGE 187
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 18 Debug Software Command List debug error_log [dump | clear | upload_toTFTP { }] debug buffer [utilization | dump | clear | upload_toTFTP ] debug output [module | all] [buffer | console] debug config error_reboot [enable | disable] debug config state [enable | disable] debug show error_reboot state debug show status {module } 18-1 debu
PAGE 188
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#debug error_log dump Command: debug error_log dump ************************************************************************** # debug log: 1 # level: fatal # clock: 10000ms # time : 2009/03/11 13:00:00 ====================== SOFTWARE FATAL ERROR ======================= Invalid mutex handle : 806D6480 Current TASK : bcmARL.
PAGE 189
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format debug buffer [utilization | dump | clear | upload_toTFTP ] Parameters utilization - Display the debug buffer’s state. dump - Display the debug message in the debug buffer. clear - Clear the debug buffer. upload_toTFTP - Upload the debug buffer to a TFTP server specified by IP address. - Specify the IPv4 address of the TFTP server.
PAGE 190
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 18-3 debug output Description This command is used to set a specified module’s debug message output to debug buffer or local console. If the user uses the command in a Telnet session, the error message also is output to the local console. Format debug output [module | all] [buffer | console] Parameters module - Specify the module list. - Enter the module list here.
PAGE 191
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator-level users can issue this command. Example To set the Switch to not need a reboot when a fatal error occurs: DES-3200-28/ME:admin#debug config error_reboot disable Command: debug config error_reboot disable Success. DES-3200-28/ME:admin# 18-5 debug config state Description This command is used to set the state of the debug.
PAGE 192
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format debug show error_reboot state Parameters None. Restrictions Only Administrator-level users can issue this command.
PAGE 193
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#debug show status module MSTP Command: debug show status module MSTP Debug Global State : Enabled MSTP : Disabled DES-3200-28/ME:admin# To show the debug state: DES-3200-28/ME:admin#debug show status Command: debug show status Debug Global State : Enabled MSTP IMPB ERPS : Disabled : Disabled : Disabled DES-3200-28/ME:admin# 189
PAGE 194
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 19 DHCP Local Relay Command List config dhcp_local_relay vlan state [enable | disable] config dhcp_local_relay vlan vlanid state [enable | disable] config dhcp_local_relay option_82 circuit_id [default | vendor1] config dhcp_local_relay option_82 ports policy [replace | drop | keep] config dhcp_local_relay option_82 remote_id [default | user_define ] enable dhcp_local_rela
PAGE 195
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 19-2 config dhcp_local_relay vlan vlanid Description This command is used to enable or disable DHCP local relay function for specified VLAN ID. Format config dhcp_local_relay vlan vlanid state [enable | disable] Parameters vlanid - Specify the VLAN ID that the DHCP local relay function will be enabled. - Enter the VLAN ID used here. state - Enable or disable DHCP local relay for specified vlan.
PAGE 196
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure the circuit id of DHCP relay agent as default: DES-3200-28/ME:admin#config dhcp_local_relay option_82 circuit_id default Command: config dhcp_local_relay option_82 circuit_id default Success. DES-3200-28/ME:admin# 19-4 config dhcp_local_relay option_82 ports Description This command is used to configure the settings of the specified ports for the policy of the option 82.
PAGE 197
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters default - Use the Switch’s system MAC address as the remote ID. user_define - Use user-defined string as the remote ID. - Enter the maximum of 32 characters. Space is allowed in the string. Restrictions Only Administrator, Operator and Power-User level users can issue this command.
PAGE 198
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 19-7 disable dhcp_local_relay Description This command is used to globally disable the DHCP local relay function on the Switch. Format disable dhcp_local_relay Parameters None. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To disable the DHCP local relay function: DES-3200-28/ME:admin#disable dhcp_local_relay Command: disable dhcp_local_relay Success.
PAGE 199
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show dhcp_local_relay Command: show dhcp_local_relay DHCP/BOOTP Local Relay Status DHCP/BOOTP Local Relay VID List : Disabled : 1 DHCP Relay Agent Information Option 82 Circuit ID : Default DHCP Relay Agent Information Option 82 Remote ID : D-Link L2Switch DES-3200-28/ME:admin# 19-9 show dhcp_local_relay option_82 ports Description This command is used to display the current DHCP local relay option 8
PAGE 200
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 20 DHCP Relay Command List config dhcp_relay {hops | time } config dhcp_relay add ipif config dhcp_relay add vlanid config dhcp_relay delete ipif config dhcp_relay delete vlanid config dhcp_relay option_82 {state [enable | disable] | check [enable | disable] | policy [replace | drop | keep] | remote
PAGE 201
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure the DHCP relay hops and time parameters: DES-3200-28/ME:admin#config dhcp_relay hops 4 time 2 Command: config dhcp_relay hops 4 time 2 Success. DES-3200-28/ME:admin# 20-2 config dhcp_relay add Description This command is used to add an IP destination address of the DHCP server for relay of DHCP/BOOTP packets.
PAGE 202
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config dhcp_relay add vlanid Parameters vlanid - Specify the VLAN ID list used for this configuration. - Enter the VLAN ID list used for this configuration here. - Enter the DHCP/BOOTP server IP address used here. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To add a DHCP/BOOTP server 10.43.21.
PAGE 203
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 20-4 config dhcp_relay delete Description This command is used to delete one of the IP destination addresses in the Switch’s relay table. Format config dhcp_relay delete ipif Parameters ipif - The name of the IP interface which contains the IP address below. - Enter the IP interface name used here. This name can be up to 12 characters long. - The DHCP/BOOTP server IP address.
PAGE 204
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To delete a DHCP/BOOTP server 10.43.21.12 from VLAN 2 and VLAN 3: DES-3200-28/ME:admin#config dhcp_relay delete vlanid 2-3 10.43.21.12 Command: config dhcp_relay delete vlanid 2-3 10.43.21.12 Success. DES-3200-28/ME:admin# 20-6 config dhcp_relay option_82 Description This command is used to configure the processing of DHCP 82 option for the DHCP relay function.
PAGE 205
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To configure dhcp_relay option 82: DES-3200-28/ME:admin#config dhcp_relay option_82 state enable Command: config dhcp_relay option_82 state enable Success. DES-3200-28/ME:admin#config dhcp_relay option_82 check disable Command: config dhcp_relay option_82 check disable Success.
PAGE 206
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure the circuit ID as default: DES-3200-28/ME:admin#config dhcp_relay option_82 circuit_id default Command: config dhcp_relay option_82 circuit_id default Success. DES-3200-28/ME:admin# 20-8 enable dhcp_relay Description This command is used to enable the DHCP relay function on the Switch. Format enable dhcp_relay Parameters None.
PAGE 207
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To disable the DHCP relay function: DES-3200-28/ME:admin#disable dhcp_relay Command: disable dhcp_relay Success. DES-3200-28/ME:admin# 20-10 show dhcp_relay Description This command is used to display the current DHCP relay configuration.
PAGE 208
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show dhcp_relay ipif System Command: show dhcp_relay ipif System DHCP/BOOTP Relay Status : Enabled DHCP/BOOTP Hops Count Limit : 4 DHCP/BOOTP Relay Time Threshold : 2 DHCP Vendor Class Identifier Option 60 State: Disabled DHCP Client Identifier Option 61 State: Disabled DHCP Relay Agent Information Option 82 State : Enabled DHCP Relay Agent Information Option 82 Check : Disabled DHCP Relay Agent Informatio
PAGE 209
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure the state of dhcp_relay option 60: DES-3200-28/ME:admin#config dhcp_relay option_60 state enable Command: config dhcp_relay option_60 state enable Success DES-3200-28/ME:admin# 20-12 config dhcp_relay option_60 add Description This command is used to configure the option 60 relay rules.
PAGE 210
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 20-13 config dhcp_relay option_60 default Description This command is used to configure the DHCP relay option 60 default drop option. When there are no match servers found for the packet based on option 60, the relay servers will be determined by the default relay server setting. When there is no matching found for the packet, the relay servers will be determined based on the default relay servers.
PAGE 211
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config dhcp_relay option_60 delete [string {relay } | ipaddress | all | default {}] Parameters string - Delete all the entries whose string is equal to the string of specified if ipaddress is not specified - Enter the DHCP option 60 string to be removed here. This value can be up to 255 characters long.
PAGE 212
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions None. Example To show DHCP option 60 information: DES-3200-28/ME:admin#show dhcp_relay option_60 Command: show dhcp_relay option_60 Default Processing Mode: Drop Default Servers: Matching Rules: String ------abc Match Type --------Exact Match IP Address --------10.90.90.
PAGE 213
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure the state of dhcp_relay option 61: DES-3200-28/ME:admin#config dhcp_relay option_61 state enable Command: config dhcp_relay option_61 state enable Success DES-3200-28/ME:admin# 20-17 config dhcp_relay option_61 add Description This command is used to add a rule to determine the relay server based on option 61. The match rule can base on either MAC address or a user-specified string.
PAGE 214
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 20-18 config dhcp_relay option_61 default Description This command is used to configure the default ruler for option 61. Format config dhcp_relay option_61 default [relay | drop] Parameters relay - Specify to relay the packet that has no option matching 61 matching rules to an IP address. - Enter the IP address used for this configuration here.
PAGE 215
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To remove a DHCP relay option 61 entry: DES-3200-28/ME:admin#config dhcp_relay option_61 delete mac_address 00-11-2233-44-55 Command: config dhcp_relay option_61 delete mac_address 00-11-22-33-44-55 Success DES-3200-28/ME:admin# 20-20 show dhcp_relay option_61 Description This command is used to show all rulers for option 61.
PAGE 216
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show dhcp_relay option_61 Command: show dhcp_relay option_61 Default Relay Rule:Drop Matching Rules: Client-ID ----------00-11-22-33-44-55 Type ---MAC Address Total Entries : 1 DES-3200-28/ME:admin# 212 Relay Rule --------Drop
PAGE 217
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 21 DHCP Server Screening Command List config filter dhcp_server [add permit server_ip ports [ | all] | delete permit server_ip ports [ | all] | ports [ | all] state [enable | disable] | illegal_server_log_suppress_duration [1min | 5min | 30min] | trap_log [enable | disable]] show filter dhcp_server 21-1 config filter dhcp_server Description This command is used to co
PAGE 218
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide state - Specify the state of the DHCP server filtering. enable - Enable the DHCP server filtering. disable - Disable the DHCP server filtering. illegal_server_log_suppress_duration - Specify the same illegal DHCP server IP address detected will be logged only once within the duration. The default value is 5 minutes. 1min - Specify that illegal server log suppress duration value will be set to 1 minute.
PAGE 219
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To display the DHCP server/client filter list created on the Switch: DES-3200-28/ME:admin#show filter dhcp_server Command: show filter dhcp_server Enabled Ports: 1-10 Trap & Log State: Disabled Illegal Server Log Suppress Duration:5 minutes Permit DHCP Server/Client Table: Server IP Address Client MAC Address ----------------- -----------------10.90.90.
PAGE 220
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 22 Digital Diagnostic Monitoring (DDM) Commands config ddm [trap | log] [enable | disable] config ddm ports [ | all ] [[temperature_threshold | voltage_threshold | bias_current_threshold | tx_power_threshold | rx_power_threshold] {high_alarm | low_alarm | high_warning | low_warning } | {state[enable|disable] | shutdown [alarm | warning | none]}] show ddm show ddm ports {
PAGE 221
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config ddm trap enable Command: config ddm trap enable Success. DES-3200-28/ME:admin# 22-2 config ddm ports Description The command is used to configure the DDM settings of the specified ports.
PAGE 222
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure the port 25’s temperature threshold: DES-3200-28/ME:admin#config ddm ports 25 temperature_threshold high_alarm 84.9532 low_alarm -10 high_warning 70 low_warning 2.25 Command: config ddm ports 25 temperature_threshold high_alarm 84.9532 low_alarm -10 high_warning 70 low_warning 2.25 According to the DDM precision definition, closest value 84.9531 is chosen. Success.
PAGE 223
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config ddm ports 25 rx_power_threshold high_alarm 4.55 low_alarm 0.01 high_warning 3.5 low_warning 0.03 Command: config ddm ports 25 rx_power_threshold high_alarm 4.55 low_alarm 0.01 high_warning 3.5 low_warning 0.03 Success.
PAGE 224
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 22-4 show ddm ports Description This command is used to show the current operating DDM parameters and configuration values of the optic module of the specified ports. There are two types of thresholds: the administrative configuration and the operation configuration threshold.
PAGE 225
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show ddm ports 25-26 status Command: show ddm ports 25-26 status Port Temperature Voltage Bias Current TX Power RX Power (in Celsius) (V) (mA) (mW) (mW) ------- ------------- ---------- -------------- ---------- -----------25 26 - CTRL+C ESC q Quit SPACE n Next Page p Previous Page r Refresh 221
PAGE 226
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 23 D-Link Unidirectional Link Detection (DULD) Command List config duld ports [ | all ] {state [enable | disable] | mode [shutdown | normal] | discovery_time }(1) show duld ports {} 23-1 config duld ports Description The command is used to configure unidirectional link detection on ports. Unidirectional link detection provides discovery mechanism based on 802.
PAGE 227
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config duld ports 1 state enable Command: config duld ports 1 state enable Success. DES-3200-28/ME:admin# 23-2 show duld ports Description This command is used to show unidirectional link detection information. Format show duld ports {} Parameters - (Optional) Specify a range of ports. Restrictions None.
PAGE 228
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 24 DoS Attack Prevention Command List config dos_prevention dos_type [{land_attack | blat_attack | tcp_null_scan | tcp_xmasscan | tcp_synfin | tcp_syn_srcport_less_1024 | ping_death_attack | tcp_tiny_frag_attack} | all] {action [drop] | state [enable | disable]} show dos_prevention {land_attack | blat_attack | tcp_null_scan | tcp_xmasscan | tcp_synfin | tcp_syn_srcport_less_1024 | ping_death_attack | tcp_tiny_frag_at
PAGE 229
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure land attack and blat attack prevention, the action is drop: DES-3200-28/ME:admin#config dos_prevention dos_type land_attack blat_attack action drop state enable Command: config dos_prevention dos_type land_attack blat_attack action drop state enable Success.
PAGE 230
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show dos_prevention Command: show dos_prevention Trap:Disabled Log:Disabled DoS Type -------------------------Land Attack Blat Attack TCP Null Scan TCP Xmas Scan TCP SYNFIN TCP SYN SrcPort Less 1024 Ping of Death Attack TCP Tiny Fragment Attack Function Version State -------Enabled Enabled Disabled Disabled Disabled Disabled Disabled Disabled : 1.
PAGE 231
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 24-4 config dos_prevention log Description This command is used to enable or disable dos prevention log state. Format config dos_prevention log [enable | disable] Parameters enable - Enable DoS prevetion log state. disable - Disable DoS prevention log state. Restrictions Only Administrator, Operator and Power-User level users can issue this command.
PAGE 232
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 25 Ethernet Ring Protection Switching (ERPS) Command List enable erps disable erps create erps raps_vlan delete erps raps_vlan config erps raps_vlan [state [enable | disable] | ring_mel | ring_port [west | east ] | rpl_port [west | east | none] | rpl_owner [enable | disable] | protected_vlan [add | delete] vlanid | revertive [enable | disable] | timer {ho
PAGE 233
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#enable erps Command: enable erps Success. DES-3200-28/ME:admin# 25-2 disable erps Description This command is used to disable the global ERPS function on a switch. Format disable erps Parameters None. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To disable ERPS: DES-3200-28/ME:admin#disable erps Command: disable erps Success.
PAGE 234
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide - Enter the VLAN ID used here. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To create an R-APS VLAN: DES-3200-28/ME:admin#create erps raps_vlan 4094 Command: create erps raps_vlan 4094 Success. DES-3200-28/ME:admin# 25-4 delete erps raps_vlan Description This command is used to delete an R-APS VLAN on a switch.
PAGE 235
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 25-5 config erps raps_vlan Description This command is used to configure the ERPS R-APS VLAN settings. The ring MEL is one field in the R-APS PDU. Note that if CFM (Connectivity Fault Management) and ERPS are used at the same time, the R-APS PDU is one of a suite of Ethernet OAM PDU. The behavior for forwarding of R-APS PDU should follow the Ethernet OAM.
PAGE 236
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide unblocked RPL port and start to send R-APS PDU with an RB flag after the link recovery is confirmed within this period of time. Revertive mode- When revertive is enabled, the traffic link is restored to the working transport link. When revertive is disabled, the traffic link is allowed to use the RPL, after recovering from a failure.
PAGE 237
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide disable - Specify that the R-APS revertive option will be disabled. timer - Specify the R-APS timer used. holdoff_time - (Optional) Specify the holdoff time of the R-APS function. The default holdoff time is 0 milliseconds. - Enter the hold off time value here. This value must be in the range of 0 to 10000 millseconds. guard_time - (Optional) Specify the guard time of the R-APS function.
PAGE 238
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config erps raps_vlan 4094 protected_vlan add vlanid 10-20 Command: config erps raps_vlan 4094 protected_vlan add vlanid 10-20 Success. DES-3200-28/ME:admin# To configure the ERPS timers for a specific R-APS VLAN: DES-3200-28/ME:admin#config erps raps_vlan 4094 timer holdoff_time 100 guard_time 1000 wtr_time 10 Command: config erps raps_vlan 4094 timer holdoff_time 100 guard_time 1000 wtr_time 10 Success.
PAGE 239
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config erps log enable Command: config erps log enable Success. DES-3200-28/ME:admin# 25-7 config erps trap Description This command is used to configure trap state of ERPS events. Format config erps trap [enable | disable] Parameters trap - Specify to enable or disable the ERPS trap state. enable - Enter enable to enable the trap state. disable - Enter disable to disable the trap state.
PAGE 240
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format show erps Parameters None. Restrictions None.
PAGE 241
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 26 Filter Command List config filter netbios [ | all] state [enable | disable] show filter netbios config filter extensive_netbios [ | all] state [enable | disable] show filter extensive_netbios 26-1 config filter netbios Description This command is used to configure the Switch to deny the NETBIOS packets on specific ports.
PAGE 242
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions None. Example To display the filter netbios list created on the Switch: DES-3200-28/ME:admin#show filter netbios Command: show filter netbios Enabled ports: 1-3 DES-3200-28/ME:admin# 26-3 config filter extensive_netbios Description This command is used to configure the Switch to filter NETBIOS packets over 802.3 flame on the specific ports.
PAGE 243
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 26-4 show filter extensive_netbios Description This command is used to display the extensive netbios state on the Switch. Format show filter extensive_netbios Parameters None. Restrictions None.
PAGE 244
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 27 Filter Database (FDB) Command List create fdb [port | drop] create fdb vlanid [port | drop] create multicast_fdb config multicast_fdb [add | delete] config fdb aging_time config multicast vlan_filtering_mode [vlanid | vlan | all] [forward_all_groups | for
PAGE 245
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#create fdb default 00-00-00-00-01-02 port 5 Command: create fdb default 00-00-00-00-01-02 port 5 Success. DES-3200-28/ME:admin# To filter a unicast MAC: DES-3200-28/ME:admin#create fdb default 00-00-00-00-01-02 drop Command: create fdb default 00-00-00-00-01-02 drop Success.
PAGE 246
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#create fdb vlanid 1 00-00-00-00-02-02 drop Command: create fdb vlanid 1 00-00-00-00-02-02 drop Success. DES-3200-28/ME:admin# 27-3 create multicast_fdb Description This command is used to create a static entry in the multicast MAC address forwarding table (database). Format create multicast_fdb Parameters - The name of the VLAN on which the MAC address resides.
PAGE 247
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide name length is 32. - The MAC address that will be added or deleted to the forwarding table. add - Specify to add ports to the multicast forwarding table. delete - Specify to remove ports from the multicast forwarding table. - Specify a range of ports to be configured. Restrictions Only Administrator, Operator and Power-User level users can issue this command.
PAGE 248
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config fdb aging_time 600 Command: config fdb aging_time 600 Success. DES-3200-28/ME:admin# 27-6 config multicast vlan_filtering_mode Description This command is used to configure the multicast packet filtering mode for VLANs. The registered group will be forwarded to the range of ports in the multicast forwarding database.
PAGE 249
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 27-7 delete fdb Description This command is used to delete a static entry from the forwarding database. Format delete fdb Parameters - The name of the VLAN on which the MAC address resides. The maximum name length is 32. - The multicast MAC address to be deleted from the static forwarding table.
PAGE 250
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To clear all FDB dynamic entries: DES-3200-28/ME:admin#clear fdb all Command: clear fdb all Success. DES-3200-28/ME:admin# 27-9 show multicast_fdb Description This command is used to display the multicast forwarding database of the Switch.
PAGE 251
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show multicast_fdb Command: show multicast_fdb VLAN Name MAC Address Egress Ports Mode : : : : default 01-00-5E-00-00-00 1-5 Static Total Entries: 1 DES-3200-28/ME:admin# 27-10 show fdb Description This command is used to display the current unicast MAC address forwarding database.
PAGE 252
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show fdb Command: show fdb Unicast MAC Address Aging Time VID ---1 1 1 1 1 = 300 VLAN Name -------------------------------default default default default default MAC Address ----------------00-01-02-03-04-00 00-23-7D-BC-08-44 00-23-7D-BC-2E-18 00-26-5A-AE-CA-1C 60-33-4B-C4-52-1A Port ----CPU 1 1 1 1 Type ------Self Dynamic Dynamic Dynamic Dynamic Status ------Forward Forward Forward Forward Forward
PAGE 253
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide long. If no parameter is specified, the device will show all multicast filtering settings in the device. Restrictions None.
PAGE 254
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 28 Flash File System (FFS) Command List show storage_media_info md {} rd {} cd {} dir {} {} rename {} del {} {recursive} erase {} move {} {} copy {} {} 28-1 show storage_media_info Descri
PAGE 255
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 28-2 md Description This command is used to create a directory. Format md {} Parameters - (Optional) Enter the drive ID used, for example, C:. - Specify the directory to be removed. The path name can be specified either as a full path name or partial name. For partial path name, it indicates the file is in the current directory.
PAGE 256
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To remove a directory: DES-3200-28/ME:admin#rd c:/abc Command: rd c:/abc Success. DES-3200-28/ME:admin# 28-4 cd Description This command is used to change the current directory. The current directory is changed under the current drive. If you want to change the working directory to the directory in another drive, then you need to change the current drive to the desired drive, and then change the current directory.
PAGE 257
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format dir {} {} Parameters - (Optional) Enter the drive ID used, for example, C:. - (Optional) Specify the directory to be removed. The path name can be specified either as a full path name or partial name. For partial path name, it indicates the file is in the current directory. Restrictions None.
PAGE 258
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters - (Optional) Enter the drive ID used, for example, C:. - Specify the file (in path form) to be renamed. - Specify the new name of the file. Restrictions Only Administrator and Operator-level users can issue this command. Example To rename a file: DES-3200-28/ME:admin#rename run.had run1.had Command: rename run.had run1.had Success.
PAGE 259
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#dir Command: dir Directory of / c: Idx --1 2 3 4 Info Attr Size ------- ---- -------drw- 0 CFG(*) -rw- 29661 RUN(*) -rw- 4879040 d--- 0 Update Time ------------------2000/04/02 06:02:04 2000/04/01 05:54:38 2000/03/26 03:15:11 2000/04/01 05:17:36 29618 KB total (24727 KB free) (*) -with boot up info Name ---------------12 config.cfg B019.
PAGE 260
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide related to the current directory. Restrictions Only Administrator and Operator-level users can issue this command.
PAGE 261
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format move {} {} Parameters - (Optional) Enter the drive ID, for example, C:. - Specify the file to be moved. The path name can be specified either as a full path name or partial name. Specify either as a full path name or partial name. For partial path name, it indicates the file is in the current directory.
PAGE 262
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To copy a file: DES-3200-28/ME:admin#copy c:/log.txt c:/log1.txt Command: copy c:/log.txt c:/log1.txt Success.
PAGE 263
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 29 Gratuitous ARP Command List config gratuitous_arp send ipif_status_up [enable | disable] config gratuitous_arp send dup_ip_detected [enable | disable] config gratuitous_arp learning [enable | disable] config gratuitous_arp send periodically ipif interval enable gratuitous_arp {ipif } {trap | log}(1) disable gratuitous_arp {ipif } {trap | log}(1) show gratu
PAGE 264
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide that the system received a ARP request packet that is sent by an IP address that match the system’s own IP address. In this case, the system knows that some body out there uses an IP address that is conflict with the system. In order to reclaim the correct host of this IP address, the system can send out the gratuitous ARP request packet for this duplicate IP address.
PAGE 265
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To show the global GratuitousARP state: DES-3200-28/ME:admin#config gratuitous_arp learning enable Command: config gratuitous_arp learning enable Success.
PAGE 266
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 29-5 enable gratuitous_arp Description The command is used to enable gratuitous ARP trap and log state. The switch can trap and log the IP conflict event to inform the administrator. By default, trap is disabled and event log is enabled. Format enable gratuitous_arp {ipif } {trap | log}(1) Parameters ipif - (Optional) Interface name of L3 interface - Enter the IP interface name here.
PAGE 267
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To disable system interface’s gratuitous ARP log and trap: DES-3200-28/ME:admin#disable gratuitous_arp ipif System trap log Command: disable gratuitous_arp ipif System trap log Success. DES-3200-28/ME:admin# 29-7 show gratuitous_arp Description This command is used to display gratuitous ARP configuration.
PAGE 268
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show gratuitous_arp Command: show gratuitous_arp Send on IPIF Status Up : Enabled Send on Duplicate IP Detected : Enabled Gratuitous ARP Learning : Enabled IP Interface Name : System Gratuitous ARP Trap : Enabled Gratuitous ARP Log : Enabled Gratuitous ARP Periodical Send Interval : 5 Total Entries: 1 DES-3200-28/ME:admin# 264
PAGE 269
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 30 IGMP / MLD Snooping Command List The Internet Group Management Protocol (IGMP) is a L3 protocol used to manage the membership of Internet Protocol multicast groups. IGMP is used by IP hosts and adjacent multicast routers to establish multicast group memberships. IGMP snooping is the process of listening to IGMP network traffic.
PAGE 270
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide show igmp_snooping {[vlan | vlanid ]} show igmp_snooping rate_limit [ports | vlanid ] show igmp_snooping group {[vlan | vlanid | ports ] {}} {data_driven} show igmp_snooping forwarding {[vlan | vlanid ]} show router_ports [vlan | vlanid | all ] {[static | dynamic | forbidde
PAGE 271
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters vlan_name - Specify the name of the VLAN for which IGMP snooping is to be configured. - Enter the VLAN name here. The VLAN name can be up to 32 characters long. vlanid - Specify the VLAN ID for which IGMP snooping is to be configured. - Enter the VLAN ID here. all - Specify to use all configured VLANs. state - (Optional) Enable or disable IGMP snooping for the chosen VLAN.
PAGE 272
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide - Configure the rate of the IGMP control packet that the Switch can process on a specific port/VLAN. The rate is specified in packets per second. The packets that exceed the limit will be dropped. no_limit - Configure the rate of the IGMP control packet to be unlimited that the Switch can process on a specific port/VLAN. The rate is specified in packets per second.
PAGE 273
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide subnet. The value of the robustness variable is used in calculating the following IGMP message intervals: - Enter the robustness variable value here. This value must be between 1 and 7. By default, the robustness variable is set to 2. You might want to increase this value if you expect a subnet to be more loose.
PAGE 274
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 30-4 config igmp access_authentication ports Description This command is used to enable or disable the IGMP Access Control function for the specified ports. If the IGMP Access Control function is enabled and the Switch receives an IGMP JOIN message, the Switch will send the access request to the RADIUS server for authentication.
PAGE 275
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide delete - Specify to delete the router ports. - Specify a range of ports to be configured. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To set up static router ports: DES-3200-28/ME:admin#config router_ports default add 1-10 Command: config router_ports default add 1-10 Success.
PAGE 276
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 30-7 enable igmp_snooping Description This command is used to enable IGMP snooping on the Switch. Format enable igmp_snooping Parameters None. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To enable IGMP snooping on the Switch: DES-3200-28/ME:admin#enable igmp_snooping Command: enable igmp_snooping Success.
PAGE 277
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To disable IGMP snooping on the Switch: DES-3200-28/ME:admin#disable igmp_snooping Command: disable igmp_snooping Success. DES-3200-28/ME:admin# 30-9 create igmp_snooping static_group Description This command is used to create an IGMP snooping static group. Member ports can be added to the static group. The static member and the dynamic member port form the member ports of a group.
PAGE 278
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#create igmp_snooping static_group vlan default 239.1.1.1 Command: create igmp_snooping static_group vlan default 239.1.1.1 Success. DES-3200-28/ME:admin# 30-10 delete igmp_snooping static_group Description This command is used to delete an IGMP snooping multicast static group. The deletion of an IGMP snooping static group will not affect the IGMP snooping dynamic member ports for a group.
PAGE 279
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config igmp_snooping static_group [vlan | vlanid ] [add | delete] Parameters vlan - Specify the name of the VLAN on which the static group resides. - Enter the VLAN name here. The VLAN name can be up to 32 characters long. vlanid - Specify the ID of the VLAN on which the static group resides. - Enter the VLAN ID here.
PAGE 280
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions None. Example To display all the IGMP snooping static groups: DES-3200-28/ME:admin#show igmp_snooping static_group VLAN ID/Name IP Address Static Member Ports -----------------------------------------------------1 / Default 239.1.1.
PAGE 281
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide state - (Optional) Specify to enable or disable the data driven learning of an IGMP snooping group. enable - Enter enable to enable the data driven learning option. By default, the state is enabled. disable - Enter disable to disable the data driven learning option. aged_out - (Optional) Enable or disable the aging out of the entry. enable - Enter enable to enable the aging out of the entry.
PAGE 282
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To set the maximum number of groups that can be learned by data driven: DES-3200-28/ME:admin#config igmp_snooping data_driven_learning max_learned_entry 50 Command: config igmp_snooping data_driven_learning max_learned_entry 50 Success.
PAGE 283
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 30-16 show igmp_snooping Description This command is used to display the current IGMP snooping configuration on the Switch. Format show igmp_snooping {[vlan | vlanid ]} Parameters vlan - (Optional) Specify the name of the VLAN for which you want to view the IGMP snooping configuration. - Enter the VLAN name here. The VLAN name can be up to 32 characters long.
PAGE 284
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show igmp_snooping Command: show igmp_snooping IGMP Snooping Global State Data Driven Learning Max Entries VLAN Name Query Interval Max Response Time Robustness Value Last Member Query Interval Querier State Querier Role Querier IP Querier Expiry Time State Fast Leave Rate Limit Report Suppression Version Data Driven Learning State Data Driven Learning Aged Out Data Driven Group Expiry Time : : : : : : :
PAGE 285
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To display the IGMP snooping rate limit for ports 1 to 15: DES-3200-28/ME:admin#show igmp_snooping rate_limit ports 1-15 Command: show igmp_snooping rate_limit ports 1-15 Port -------1 2 3 4 5 Rate Limit ----------No Limit 100 No Limit No Limit No Limit Total Entries: 5 30-18 show igmp_snooping group Description This command is used to display the current IGMP snooping group configuration on the Switch.
PAGE 286
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show igmp_snooping group Command: show igmp_snooping group Source/Group VLAN Name/VID Member Ports UP Time Expiry Time Filter Mode : : : : : : 10.0.0.1/225.0.0.1 default/1 5 6 254 INCLUDE Source/Group VLAN Name/VID Member Ports UP Time Expiry Time Filter Mode : : : : : : 10.0.0.10/225.0.0.
PAGE 287
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Member Ports UP Time Expiry Time Filter Mode : : : : 5 10 258 EXCLUDE Source/Group VLAN Name/VID Member Ports UP Time Expiry Time Filter Mode : : : : : : NULL/226.0.0.2 default/1 5 9 259 EXCLUDE Source/Group VLAN Name/VID Member Ports Router Ports UP Time Expiry Time Filter Mode : : : : : : : NULL/226.0.0.3 default/1 Source/Group VLAN Name/VID Member Ports UP Time Expiry Time Filter Mode : : : : : : NULL/239.255.
PAGE 288
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide - Enter the VLAN ID list here. If no parameter is specified, the system will display all current IGMP snooping forwarding table entries of the Switch. Restrictions None. Example To show all IGMP snooping forwarding entries located on the Switch: DES-3200-28/ME:admin#show igmp_snooping forwarding Command: show igmp_snooping forwarding VLAN Name : Source IP : Multicast Group: Port Member : default * 225.0.0.
PAGE 289
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide all - Specify all VLANs on which the router port resides. static - (Optional) Displays router ports that have been statically configured. dynamic - (Optional) Displays router ports that have been dynamically configured. forbidden - (Optional) Displays forbidden router ports that have been statically configured. If no parameter is specified, the system will display all currently configured router ports on the Switch.
PAGE 290
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide - Enter the list of port to be displayed here. Restrictions None.
PAGE 291
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28P:admin# To display the IGMP snooping statistics counter for a port: DES-3200-28/ME:admin#show igmp_snooping statistic counter ports 1 Command: show igmp_snooping statistic counter ports 1 Port # : 1 -------------------------------------------------Group Number : 0 Receive Statistics Query IGMP v1 Query IGMP v2 Query IGMP v3 Query Total Dropped By Rate Limitation Dropped By Multicast VLAN Report & Leave IGMP v1 Rep
PAGE 292
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 30-22 show igmp access_authentication ports Description This command is used to display the current IGMP Access Control configuration. Format show igmp access_authentication ports [all | ] Parameters all - Specify all ports to be displayed. - Specify a range of ports to be displayed. Restrictions None.
PAGE 293
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 12 Disabled 13 Disabled 14 Disabled 15 Disabled 16 Disabled 17 Disabled 18 Disabled 19 Disabled 20 Disabled CTRL+C ESC q Quit SPACE n Next Page ENTER Next Entry a All 30-23 clear igmp_snooping statistics counter Description This command is used to clear the IGMP snooping statistics counter. Format clear igmp_snooping statistics counter Parameters None.
PAGE 294
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters vlan_name - Specify the name of the VLAN for which MLD snooping is to be configured. - Enter the VLAN name here. The VLAN name can be up to 32 characters long. vlanid - Specify the ID of the VLAN for which MLD snooping is to be configured. - Enter the VLAN ID list here. all - Specify all VLANs for which MLD snooping is to be configured.
PAGE 295
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide - Enter the VLAN ID list here. all - Specify all VLANs for which MLD snooping querier is to be configured. query_interval - Specify the amount of time in seconds between general query transmissions. The default setting is 125 seconds. - Enter the query interval value here. This value must be between 1 and 65535 seconds.
PAGE 296
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 30-26 config mld_snooping router_ports Description This command is used to designate a range of ports as being connected to multicast-enabled routers. This will ensure that all packets with such a router as its destination will reach the multicast-enabled router, regardless of protocol, etc.
PAGE 297
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters vlan - Specify the name of the VLAN on which the forbidden router port resides. - Enter the VLAN name here. The VLAN name can be up to 32 characters long. vlanid - Specify the ID of the VLAN on which the forbidden router port resides. - Enter the VLAN ID list here. add - Specify to add the forbidden router ports. delete - Specify to delete the forbidden router ports.
PAGE 298
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#enable mld_snooping Command: enable mld_snooping Success. DES-3200-28/ME:admin# 30-29 disable mld_snooping Description This command is used to disable MLD snooping on the Switch.
PAGE 299
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide configuration. - Enter the VLAN name here. The VLAN name can be up to 32 characters long. vlanid - (Optional) Specify the ID of the VLAN for which you want to view the MLD snooping configuration. - Enter the VLAN ID list here. If VLAN is not specified, the system will display all current MLD snooping configurations. Restrictions None.
PAGE 300
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format show mld_snooping group {[vlan | vlanid | ports ] {}} {data_driven} Parameters vlan - (Optional) Specify the name of the VLAN for which you want to view MLD snooping group information. If VLAN and ports and IP address are not specified, the system will display all current MLD snooping group information. - Enter the VLAN name here.
PAGE 301
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show mld_snooping group Command: show mld_snooping group Source/Group VLAN Name/VID Member Ports UP Time Expiry Time Filter Mode : : : : : : 2001::1/FE1E::1 default/1 1-2 26 258 INCLUDE Source/Group VLAN Name/VID: Member Ports UP Time Expiry Time Filter Mode : : : : : : 2002::2/FE1E::1 default/1 3 29 247 EXCLUDE Source/Group VLAN Name/VID Member Ports UP Time Expiry Time Filter Mode : : : : : : NUL
PAGE 302
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 30-32 show mld_snooping forwarding Description This command is used to display the Switch’s current MLD snooping forwarding table. It provides an easy way for users to check the list of ports that the multicast group that comes from specific sources will be forwarded to. The packet comes from the source VLAN. They will be forwarded to the forwarding VLAN.
PAGE 303
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 30-33 show mld_snooping mrouter_ports Description This command is used to display the currently configured router ports on the Switch. Format show mld_snooping mrouter_ports [vlan | vlanid | all] {[static | dynamic | forbidden]} Parameters vlan - Specify the name of the VLAN on which the router port resides. - Enter the VLAN name here. The VLAN name can be up to 32 characters long.
PAGE 304
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide The static group will only take effect when MLD snooping is enabled on the VLAN. An active static group must be equal to a static MLD group with a link-up member port. For those static member ports, the device needs to emulate the MLD protocol operation to the querier, and forward the traffic destined to the multicast group to the member ports.
PAGE 305
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide - Enter the VLAN ID list here. - Specify the multicast group IP address. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To delete an MLD snooping static group for VLAN 1, group FF1E::1: DES-3200-28/ME:admin#delete mld_snooping static_group vlan default FF1E::1 Command: delete mld_snooping static_group vlan default FF1E::1 Success.
PAGE 306
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config mld_snooping static_group vlan default FF1E::1 delete 9-10 Command: config mld_snooping static_group vlan default FF1E::1 delete 9-10 Success. DES-3200-28/ME:admin# 30-37 show mld_snooping static_group Description This command used to display the MLD snooping multicast group static members.
PAGE 307
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide snooping entry, the MLD protocol will take care the aging out of the entry. For a data-driven entry, the entry can be specified not to be aged out or to be aged out by the aged timer. When the data driven learning is enabled, and the data driven table is not full, the multicast filtering mode for all ports is ignored. That is, the multicast packets will be forwarded to router ports.
PAGE 308
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 30-39 config mld_snooping data_driven_learning max_learned_entry Description This command is used to configure the maximum number of groups that can be learned by data driven. When the table is full, the system will stop the learning of the new data-driven groups. Traffic for the new groups will be dropped.
PAGE 309
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide - Enter the VLAN name here. vlanid - Specify the VLAN ID. - Enter the VLAN ID list here. - Specify the group’s IP address learned by data driven. all - Specify to clear all data driven groups of the specified VLAN. Restrictions Only Administrator, Operator and Power-User level users can issue this command.
PAGE 310
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin# show mld_snooping statistic counter vlanid 1 Command: show mld_snooping statistic counter vlanid 1 VLAN Name : Default ----------------------------------------------Total Groups : 10 Receive Statistics Query MLD v1 Query : 1 MLD v2 Query : 1 Total : 2 Dropped By Rate Limitation : 1 Dropped By Multicast VLAN : 1 Report & Leave MLD v1 Report MLD v2 Report MLD v1 Done Total Dropped By Rate Limitation Dropped
PAGE 311
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To clear MLD snooping statistics counter: DES-3200-28/ME:admin#clear mld_snooping statistics counter Command: clear mld_snooping statistics counter Success.
PAGE 312
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config mld_snooping rate_limit ports 1 100 Command: config mld_snooping rate_limit ports 1 100 Success. DES-3200-28/ME:admin# 30-44 show mld_snooping rate_limit Description This command is used to display the rate limit of MLD control packets that are allowed by each port or VLAN. Format show mld_snooping rate_limit [ports | vlanid ] Parameters ports - Specify a list of ports.
PAGE 313
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 31 IP-MAC-Port Binding (IMPB) Command List create address_binding ip_mac ipaddress mac_address {ports [ | all]} config address_binding ip_mac ports [ | all] {arp_inspection [strict | loose | disable] | ip_inspection [enable | disable] | protocol [ipv4] | allow_zeroip [enable | disable] | forward_dhcppkt [enable | disable] | stop_learning_threshold } delete address_bin
PAGE 314
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To create an IMPB entry: DES-3200-28/ME:admin#create address_binding ip_mac ipaddress 10.1.1.1 mac_address 00-00-00-00-00-11 Command: create address_binding ip_mac ipaddress 10.1.1.1 mac_address 00-00-0000-00-11 Success.
PAGE 315
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide When set to disabled, the broadcast DHCP packet received by the specified port will not be forwarded. This setting is effective when DHCP Snooping is enabled, in this case DHCP packets trapped by the CPU must be forwarded by the software. This setting controls the forwarding behavior in this situation. enable - Specify that the forward DHCP packets option will be enabled.
PAGE 316
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#delete address_binding blocked vlan_name v31 mac_address 00-00-00-00-00-11 Command: delete address_binding blocked vlan_name v31 mac_address 00-00-00-0000-11 Success. DES-3200-28/ME:admin# 31-4 delete address_binding ip_mac Description This command is used to delete an IMPB entry.
PAGE 317
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters ipaddress - Specify the IP address of the entry being updated. - Enter the IP address used here. mac_address - Specify the MAC address of the entry being updated - Enter the MAC address used here. ports - (Optional) Specify which ports are used for the IMPB entry being updated. If not specified, then it is applied to all ports. - Enter the list of port used here.
PAGE 318
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show address_binding Command: show address_binding Trap/Log DHCP Snoop : Disabled : Disabled DES-3200-28/ME:admin# To show the IMPB ports: DES-3200-28/ME:admin#show address_binding ports Command: show address_binding ports ARP: ARP Inspection Port ----1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 CTRL+C 31-7 ARP IP IP: IP Inspection Protocol Zero IP -------- -------Disabled Disabled Disabled Disabled Dis
PAGE 319
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide vlan_name - Specify the name of the VLAN to which the blocked MAC address belongs. - Enter the VLAN name used. mac_address - Specify the MAC address of the entry or the blocked MAC address. - Enter the MAC address of the entry or the blocked MAC address. Restrictions None.
PAGE 320
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show address_binding ip_mac all Command: show address_binding ip_mac all M(Mode) - D:DHCP, S:Static ACL - A:Active I:Inactive IP Address MAC Address M ACL Ports --------------------------------------- ----------------- -- -- -------------10.1.1.
PAGE 321
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To enable DHCP IPv4 snooping mode: DES-3200-28/ME:admin#enable address_binding dhcp_snoop Command: enable address_binding dhcp_snoop Success. DES-3200-28/ME:admin# 31-10 disable address_binding dhcp_snoop Description This command is used to disable DHCP snooping mode.
PAGE 322
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 31-11 clear address_binding dhcp_snoop binding_entry ports Description This command is used to clear the DHCP snooping entries learned for the specified ports. Format clear address_binding dhcp_snoop binding_entry ports [ | all] Parameters - Enter the list of ports used. all - Specify that all the ports will be used.
PAGE 323
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To show the DHCP snooping state: DES-3200-28/ME:admin#show address_binding dhcp_snoop Command: show address_binding dhcp_snoop DHCP_Snoop : Disabled DES-3200-28/ME:admin# To display DHCP snooping maximun entry configuration: DES-3200-28/ME:admin#show address_binding dhcp_snoop max_entry Command: show address_binding dhcp_snoop max_entry Port Max Entry ---- --------1 No Limit 2 No Limit 3 No Limit 4 No Limit 5 No Lim
PAGE 324
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide - Enter the port number used here. Restrictions None. Example To display the DHCP snooping binding entries: DES-3200-28/ME:admin#show address_binding dhcp_snoop binding_entry Command: show address_binding dhcp_snoop binding_entry S (Status) - A: Active, I: Inactive Time - Left Time (sec) IP Address --------------------------------------10.62.58.35 10.33.53.
PAGE 325
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To set the maximum number of DHCP IPv4 snooping entries that ports 1–3 can learned to 10: DES-3200-28/ME:admin#config address_binding dhcp_snoop max_entry ports 1-3 limit 10. Command: config address_binding dhcp_snoop max_entry ports 1-3 limit 10. Success.
PAGE 326
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To disable IMPB traps and logs: DES-3200-28/ME:admin#disable address_binding trap_log Command: disable address_binding trap_log Success. DES-3200-28/ME:admin# 31-17 config address_binding recover_learning Description This command is used to recover IMPB checking.
PAGE 327
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 31-18 debug address_binding Description This command is used to start the IMPB debug when the IMPB module receives an ARP/IP packet or a DHCP packet. Format debug address_binding [event | dhcp | all] state [enable | disable] Parameters event - To print out the debug messages when IMPB module receives ARP/IP packets. dhcp - To print out the debug messages when the IMPB module receives the DHCP packets.
PAGE 328
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To stop IMPB debug: starting when the IMPB module receives an ARP/IP or DHCP packet: DES-3200-28/ME:admin#no debug address_binding Command: no debug address_binding Success.
PAGE 329
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 32 IPv6 Neighbor Discover Command List create ipv6 neighbor_cache ipif delete ipv6 neighbor_cache ipif [ | all] [ | static | dynamic | all] show ipv6 neighbor_cache ipif [ | all] [ipv6address | static | dynamic | all] config ipv6 nd ns ipif retrans_time show ipv6 nd {ipif } 32-
PAGE 330
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 32-2 delete ipv6 neighbor_cache Description This command is used to delete a neighbor cache entry or static neighbor cache entries from the address cache or all address cache entries on this IP interface. Both static and dynamic entries can be deleted. Format delete ipv6 neighbor_cache ipif [ | all] [ | static | dynamic | all] Parameters ipif - Specify the IPv6 interface name.
PAGE 331
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide - Enter the IP interface name here. This name can be up to 12 characters long. all - Specify that all the interface will be displayed. ipv6address - The neighbor’s address. - Enter the IPv6 address here. static - Static neighbor cache entry. dynamic - Dynamic entries. all - All entries include static and dynamic entries.
PAGE 332
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure the retrans_time of IPv6 ND neighbor solicitation: DES-3200-28/ME:admin#config ipv6 nd ns ipif Zira retrans_time 1000000 Command: config ipv6 nd ns ipif Zira retrans_time 1000000 Success. DES-3200-28/ME:admin# 32-5 show ipv6 nd Description This command is used to display information regarding neighbor detection on the Switch.
PAGE 333
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 33 IPv6 Route Command List create ipv6route [default] [ | ] {} delete ipv6route [default] [ | | all] show ipv6route 33-1 create ipv6route Description This command is used to create an IPv6 default route. If the next hop is a global address, it is not needed to indicate the interface name.
PAGE 334
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format delete ipv6route [default] [ | | all] Parameters default - Specify the default route. - Enter the IP interface name used here. This name can be up to 12 characters long. - Specify the next hop address for the default route. - Specify the next hop address for the default route. all - Specify that all static created routes will be deleted.
PAGE 335
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show ipv6route Command: show ipv6route IPv6 Prefix: ::/0 Next Hop : 3001::254 Status : Inactive Protocol: Static IPIF : System Total Entries: 1 DES-3200-28/ME:admin# 331 Metric: 1
PAGE 336
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 34 Jumbo Frame Command List enable jumbo_frame disable jumbo_frame show jumbo_frame 34-1 enable jumbo_frame Description This command is used to configure the jumbo frame setting as enable. Format enable jumbo_frame Parameters None. Restrictions Only Administrator and Operator-level users can issue this command.
PAGE 337
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions Only Administrator and Operator-level users can issue this command. Example To disable the Jumbo frame: DES-3200-28/ME:admin#disable jumbo_frame Command: disable jumbo_frame Success. DES-3200-28/ME:admin# 34-3 show jumbo_frame Description This command is used to display the current configuration of jumbo frame. Format show jumbo_frame Parameters None. Restrictions None.
PAGE 338
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 35 Layer 2 Protocol Tunneling (L2PT) Command List enable l2protocol_tunnel disable l2protocol_tunnel config l2protocol_tunnel ports [ | all] type [uni tunneled_protocol [{stp | gvrp | protocol_mac [01-00-0C-CC-CC-CC | 01-00-0C-CC-CC-CD]}(1) | all] {threshold } | nni | none] show l2protocol_tunnel {[uni | nni]} 35-1 enable l2protocol_tunnel Description This command is used to enable the Laye
PAGE 339
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions Only Administrator and Operator-level users can issue this command. Example To disable the Layer 2 protocol tunneling function: DES-3200-28/ME:admin#disable l2protocol_tunnel Command: disable l2protocol_tunnel Success. DES-3200-28/ME:admin# 35-3 config l2protocol_tunnel ports Description This command is used to configure Layer 2 protocol tunneling on ports.
PAGE 340
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 01-00-0C-CC-CC-CD - Specify the MAC address as 01-00-0C-CC-CC-CD. all - All tunnel-abled Layer 2 protocols will be tunneled on the ports. threshold - (Optional) Specify the drop threshold for packets-per-second accepted on the UNI ports. The ports drop the PDU if the protocol’s threshold is exceeded. - The range of the threshold value is 0 to 65535 (packet/second). The value 0 means no limit.
PAGE 341
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show l2protocol_tunnel Command: show l2protocol_tunnel Global State : Enabled UNI Ports : 1-4 NNI Ports : DES-3200-28/ME:admin# To show Layer 2 protocol tunneling information summary: DES-3200-28/ME:admin#show l2protocol_tunnel uni Command: show l2protocol_tunnel uni UNI Port ---1 2 3 4 Tunneled Protocol ----------------STP STP STP STP Threshold (packet/sec) -----------0 0 0 0 DES-3200-28/ME:admin# 33
PAGE 342
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 36 Link Aggregation Command List create link_aggregation group_id {type [lacp | static]} delete link_aggregation group_id config link_aggregation group_id {master_port | ports | state [enable | disable] config link_aggregation algorithm [mac_source | mac_destination|mac_source_dest | ip_source | ip_destination | ip_source_dest] show link_aggregation {group_id | algori
PAGE 343
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 36-2 delete link_aggregation group_id Description This command is used to delete a previously configured link aggregation group. Format delete link_aggregation group_id Parameters group_id - Specify the group id. The number of link aggregation groups is project dependency. The group number identifies each of the groups. - Enter the group ID value here.
PAGE 344
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide ports’ state machine will start. enable - Enable the specified link aggregation group. disable - Disable the specified link aggregation group. Restrictions Only Administrator, Operator and Power-User level users can issue this command.
PAGE 345
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config link_aggregation algorithm mac_source_dest Command: config link_aggregation algorithm mac_source_dest Success. DES-3200-28/ME:admin# 36-5 show link_aggregation Description This command is used to display the current link aggregation configuration on the Switch. Format show link_aggregation {group_id | algorithm} Parameters group_id - (Optional) Specify the group id.
PAGE 346
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show link_aggregation Command: show link_aggregation Link Aggregation Algorithm = MAC-Source-Dest Group ID Type Master Port Member Port Active Port Status Flooding Port : : : : : : : 1 LACP 5 5-7 Enabled Total Entries : 1 DES-3200-28/ME:admin# Link aggregation group disabled: DES-3200-28/ME:admin#show link_aggregation Command: show link_aggregation Link Aggregation Algorithm = MAC-Source-Dest Group ID
PAGE 347
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide passive - Specify to set the LACP mode as passive. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To config port LACP mode: DES-3200-28/ME:admin#config lacp_port 1-12 mode active command: config lacp_port 1-12 mode active Success. DES-3200-28/ME:admin# 36-7 show lacp_port Description This command is used to display the current mode of LACP of the ports.
PAGE 348
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show lacp_port Command: show lacp_port Port -----1 2 3 4 5 6 7 8 9 10 11 12 Activity -------Active Active Active Active Active Active Active Active Active Active Active Active DES-3200-28/ME:admin# 344
PAGE 349
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 37 Link Layer Discovery Protocol (LLDP) Command List enable lldp disable lldp config lldp [message_tx_interval | message_tx_hold_multiplier | tx_delay | reinit_delay ] config lldp notification_interval config lldp ports [ | all] [notification [enable | disable] | admin_status [tx_only | rx_only | tx_and_rx | disable] | mgt_addr [ipv4 | ip
PAGE 350
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To enable LLDP: DES-3200-28/ME:admin#enable lldp Command: enable lldp Success. DES-3200-28/ME:admin# 37-2 disable lldp Description This command is used to stop sending and receiving of LLDP advertisement packet. Format disable lldp Parameters None.
PAGE 351
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config lldp [message_tx_interval | message_tx_hold_multiplier | tx_delay | reinit_delay ] Parameters message_tx_interval - Changes the interval between consecutive transmissions of LLDP advertisements on any given port. The default setting 30 seconds. - Enter the message transmit interval value here. This value must be between 5 and 32768 seconds.
PAGE 352
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide - Enter the notification interval value here. This value must be between 5 and 3600 seconds. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To changes the notification interval to 10 second: DES-3200-28/ME:admin#config lldp notification_interval 10 Command: config lldp notification_interval 10 Success.
PAGE 353
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide mgt_addr - Specify the management address used. ipv4 - Specify the IPv4 address used. - Enter the IP address used for this configuration here. ipv6 - Specify the IPv6 address used. - Enter the IPv6 address used for this configuration here. enable - Specify that the advertising indicated management address instance will be enabled.
PAGE 354
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide eapol - (Optional) Specify that the EAPOL protocol will be advertised. lacp - (Optional) Specify that the LACP protocol will be advertised. gvrp - (Optional) Specify that the GVRP protocol will be advertised. stp - (Optional) Specify that the STP protocol will be advertised. enable - Specify that the protocol identity TLV according to the protocol specified will be adverstised.
PAGE 355
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide To enable ports 1-2 for manage address entry: DES-3200-28/ME:admin#config lldp ports 1-2 mgt_addr ipv4 10.90.90.90 enable Command: config lldp ports 1-2 mgt_addr ipv4 10.90.90.90 enable Success.
PAGE 356
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config lldp ports all dot1_tlv_protocol_identity all enable Command: config lldp ports all dot1_tlv_protocol_identity all enable Success.
PAGE 357
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format show lldp Parameters None. Restrictions None.
PAGE 358
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide ipv6 - (Optional) Specify the IPv6 address used for the display. - Enter the IPv6 address used for this configuration here. Restrictions None. Example To display management address information: DES-3200-28/ME:admin#show lldp mgt_addr ipv4 10.90.90.90 Command: show lldp mgt_addr ipv4 10.90.90.90 Address 1 : -----------------------------------------------Subtype : IPv4 Address : 10.90.90.
PAGE 359
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show lldp ports Command: show lldp ports 1 1 Port ID : 1 ----------------------------------------------------------------Admin Status : TX_and_RX Notification Status : Enabled Advertised TLVs Option : Port Description Disabled System Name Enabled System Description Disabled System Capabilities Disabled Enabled Management Address 10.90.90.
PAGE 360
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To display outbound LLDP advertisements for port 1 in detailed mode. Port description on the display should use the same value as ifDescr. DES-3200-28/ME:admin#show lldp local_ports 1 mode detailed Command: show lldp local_ports 1 mode detailed Port ID : 1 ----------------------------------------------------------------------------Port ID Subtype : Local Port ID : 1 Port Description : D-Link DES-3200-28/ME 4.04.
PAGE 361
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show lldp local_ports 1 mode normal Command: show lldp local_ports 1 mode normal Port ID : 1 ----------------------------------------------------------------------------Port ID Subtype : Local Port ID : 1 Port Description : D-Link DES-3200-28/ME R4.04.
PAGE 362
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide brief - Display the information in brief mode. normal - Display the information in normal mode. This is the default display mode. detailed - Display the information in detailed mode. Restrictions None.
PAGE 363
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide To display remote table in normal mode: DES-3200-28/ME:admin# show lldp remote_ports 3 mode normal Command: show lldp remote_ports 3 mode normal Port ID : 3 ------------------------------------------------------------------------------Remote Entities Count : 1 Entity 1 Chassis ID Subtype : MAC Address Chassis ID : 00-12-13-04-05-00 Port ID Subtype : MAC Address Port ID : 00-12-13-04-05-03 Port Description : D-Link DES-3200-28/
PAGE 364
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin# show lldp remote_ports 3 mode detailed Command: show lldp remote_ports 3 mode detailed Port ID : 3 ------------------------------------------------------------------------------Remote Entities Count : 1 Entity 1 Chassis ID Subtype : MAC Address Chassis ID : 00-12-13-04-05-00 Port ID Subtype : MAC Address Port ID : 00-12-13-04-05-03 Port Description : D-Link DES-3200-28/ME R4.04.
PAGE 365
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 37-12 show lldp statistics Description This command is used to display an overview of neighbor detection activity on the Switch. Format show lldp statistics Parameters None. Restrictions None.
PAGE 366
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To display statistics information of port 1: DES-3200-28/ME:admin#show lldp statistics ports 1 Command: show lldp statistics ports 1 Port ID : 1 --------------------------------------------LLDPStatsTXPortFramesTotal : 23 LLDPStatsRXPortFramesDiscardedTotal : 0 LLDPStatsRXPortFramesErrors : 0 LLDPStatsRXPortFramesTotal : 0 LLDPStatsRXPortTLVsDiscardedTotal : 0 LLDPStatsRXPortTLVsUnrecognizedTotal : 0 LLDPStatsRXPortAgeo
PAGE 367
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 38 Loop Back Detection (LBD) Command List config loopdetect {recover_timer [ | ] | interval | mode [port-based | vlan-based]} config loopdetect ports [ | all] state [enable | disable] enable loopdetect disable loopdetect show loopdetect show loopdetect ports {} config loopdetect trap [none | loop_detected | loop_cleared | both] config loopdetect log state [en
PAGE 368
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To set the auto-recover time to 0, which disables the auto-recovery mechanism, the interval to 20 seconds and specify VLAN-based mode: DES-3200-28/ME:admin#config loopdetect recover_timer 0 interval 20 mode vlanbased Command: config loopdetect recover_timer 0 interval 20 mode vlan-based Success.
PAGE 369
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format enable loopdetect Parameters None. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To enable the LBD function globally: DES-3200-28/ME:admin#enable loopdetect Command: enable loopdetect Success. DES-3200-28/ME:admin# 38-4 disable loopdetect Description This command is used to disable the LBD function globally on the Switch.
PAGE 370
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#disable loopdetect Command: disable loopdetect Success. DES-3200-28/ME:admin# 38-5 show loopdetect Description This command is used to display the LBD global configuration. Format show loopdetect Parameters None. Restrictions Only Administrator and Operator-level users can issue this command.
PAGE 371
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters ports - Specify the range of member ports that will display the LBD settings. - Enter the list of port to be configured here. If no port is specified, the configuration for all ports will be displayed. Restrictions None.
PAGE 372
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To specify that traps will be sent when the loop condition is detected or cleared: DES-3200-28/ME:admin#config loopdetect trap both Command: config loopdetect trap both Success. DES-3200-28/ME:admin# 38-8 config loopdetect log Description This command is used to configure the log state for LBD. The default value is enabled.
PAGE 373
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 39 MAC Notification Command List enable mac_notification disable mac_notification config mac_notification {interval | historysize } config mac_notification ports [ | all] [enable | disable] show mac_notification show mac_notification ports {} 39-1 enable mac_notification Description This command is used to enable global MAC address table notification on the Switch.
PAGE 374
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To disable mac_notification function: DES-3200-28/ME:admin#disable mac_notification Command: disable mac_notification Success. DES-3200-28/ME:admin# 39-3 config mac_notification Description This command is used to configure the Switch’s MAC address table notification global settings.
PAGE 375
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 39-4 config mac_notification ports Description This command is used to configure the port’s MAC address table notification status settings. Format config mac_notification ports [ | all] [enable | disable] Parameters - Enter a list of ports used for the configuration here. all - Specify that all the ports will be used for this configuration. enable - Enable the port’s MAC address table notification.
PAGE 376
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To show the Switch’s Mac address table notification global settings: DES-3200-28/ME:admin#show mac_notification Command: show mac_notification Global MAC Notification Settings State : Disabled Interval : 1 History Size : 1 DES-3200-28/ME:admin# 39-6 show mac_notification ports Description This command is used to display the port’s Mac address table notification status settings.
PAGE 377
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show mac_notification ports Command: show mac_notification ports Port MAC Address Table Notification State ------ -----------------------------------1 Disabled 2 Disabled 3 Disabled 4 Disabled 5 Disabled 6 Disabled 7 Disabled 8 Disabled 9 Disabled 10 Disabled 11 Disabled 12 Disabled 13 Disabled 14 Disabled 15 Disabled 16 Disabled 17 Disabled 18 Disabled 19 Disabled 20 Disabled CTRL+C ESC q Quit SPACE n Nex
PAGE 378
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 40 MAC-based Access Control Command List enable mac_based_access_control disable mac_based_access_control config mac_based_access_control password config mac_based_access_control method [local | radius] config mac_based_access_control guest_vlan ports config mac_based_access_control ports [ | all] {state [enable | disable] | mode [port_based | host_based] | aging_time [infinite |
PAGE 379
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To enable the MAC-based Access Control global state: DES-3200-28/ME:admin#enable mac_based_access_control Command: enable mac_based_access_control Success. DES-3200-28/ME:admin# 40-2 disable mac_based_access_control Description This command is used to disable MAC-based Access Control. Format disable mac_based_access_control Parameters None.
PAGE 380
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters password - In RADIUS mode, the Switch will communicate with the RADIUS server using this password. The maximum length of the key is 16. - Enter the password used here. The default password is “default”. Restrictions Only Administrator, Operator and Power-User level users can issue this command.
PAGE 381
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 40-5 config mac_based_access_control guest_vlan Description This command is used to assign a specified port list to the MAC-based Access Control guest VLAN. Ports that are not contained in port list will be removed from the MAC-based Access Control guest VLAN. For detailed information on the operation of MAC-based Access Control guest VLANs, please see the description for the “config mac_based_access_control ports” command.
PAGE 382
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide  Before the authentication process starts, the user is able to forward traffic under the guest VLAN.  After the authentication process, the user will be able to access the assigned VLAN. If the port authorize mode is port based mode, when the port has been moved to the authorized VLAN, the subsequent users will not be authenticated again. They will operate in the current authorized VLAN.
PAGE 383
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To configure an unlimited number of maximum users for MAC-based Access Control on ports 1 to 8: DES-3200-28/ME:admin#config mac_based_access_control ports 1-8 max_users no_limit Command: config mac_based_access_control ports 1-8 max_users no_limit Success.
PAGE 384
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To create a MAC-based Access Control guest VLAN: DES-3200-28/ME:admin#create mac_based_access_control guest_vlan VLAN8 Command: create mac_based_access_control guest_vlan VLAN8 Success. DES-3200-28/ME:admin# 40-8 delete mac_based_access_control Description This command is used to remove a MAC-based Access Control guest VLAN.
PAGE 385
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format clear mac_based_access_control auth_state [ports [all | ] | mac_addr ] Parameters ports - To specify the port range to delete MAC addresses on them. all - To specify all MAC-based Access Control enabled ports to delete MAC addresses. - Enter the list of port used for this configuration here. mac_addr - To delete a specified host with this MAC address.
PAGE 386
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters mac - Specify the MAC address that can pass local authentication. - Enter the MAC address used here. vlan - (Optional) Specify the target VLAN by using the VLAN name. When this host is authorized, it will be assigned to this VLAN. - Enter the VLAN name here. This name can be up to 32 characters long. vlanid - (Optional) Specify the target VLAN by using the VID.
PAGE 387
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To configure the target VLAN “default” for the MAC-based Access Control local database entry 0000-00-00-00-01: DES-3200-28/ME:admin#config mac_based_access_control_local mac 00-00-00-00-0001 vlan default Command: config mac_based_access_control_local mac 00-00-00-00-00-01 vlan default Success.
PAGE 388
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide To delete the MAC-based Access Control local database entry for the VLAN name VLAN3: DES-3200-28/ME:admin#delete mac_based_access_control_local vlan VLAN3 Command: delete mac_based_access_control_local vlan VLAN3 Success. DES-3200-28/ME:admin# 40-13 config mac_based_access_control authorization attributes Description This command is used to enable or disable the acceptation of an authorized configuration.
PAGE 389
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config mac_based_access_control authorization attributes local disable Command: config mac_based_access_control authorization attributes local disable Success. DES-3200-28/ME:admin# 40-14 show mac_based_access_control Description This command is used to display the MAC-based Access Control setting.
PAGE 390
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format show mac_based_access_control_local {[mac | vlan | vlanid ]} Parameters mac - (Optional) Displays MAC-based Access Control local database entries for a specific MAC address. - Enter the MAC address used here. vlan - (Optional) Displays MAC-based Access Control local database entries for a specific target VLAN name. - Enter the VLAN name here.
PAGE 391
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions None.
PAGE 392
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config mac_based_access_control max_users 128 Command: config mac_based_access_control max_users 128 Success. DES-3200-28/ME:admin# 40-18 config mac_based_access_control trap state Description This command is used to enable or disable sending of MAC-based Access Control traps.
PAGE 393
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide disable - Disable log for MAC-based Access Control. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To disable log state of MAC-based Access Control: DES-3200-28/ME:admin#config mac_based_access_control log state disable Command: config mac_based_access_control log state disable Success.
PAGE 394
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 41 MAC-based VLAN Command List create mac_based_vlan mac_address [vlan | vlanid ] delete mac_based_vlan {mac_address [vlan | vlanid ]} show mac_based_vlan {mac_address | [vlan | vlanid ]} 41-1 create mac_based_vlan mac_address Description This command is used to create a static MAC-based VLAN entry.
PAGE 395
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 41-2 delete mac_based_vlan Description This command is used to delete the static MAC-based VLAN entry. Format delete mac_based_vlan {mac_address [vlan | vlanid ]} Parameters mac_address - (Optional) Specify the MAC address used. - Enter the MAC address used here. vlan - (Optional) The VLAN to be associated with the MAC address. - Enter the VLAN name here.
PAGE 396
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide vlan - (Optional) Specify the VLAN that you would like to display. - Enter the VLAN name here. This name can be up to 32 characters long. vlanid - (Optional) Specify the VLAN by VLAN ID. - Enter the VLAN ID here. This value must be between 1 and 4094. Restrictions None. Example In the following example, MAC address “00-80-c2-33-c3-45” is assigned to VLAN 300 by manual config.
PAGE 397
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 42 Mirror Command List config mirror port {[add | delete] source ports [rx | tx | both]} enable mirror disable mirror show mirror 42-1 config mirror Description This command is used to configure a mirror port − source port pair on the Switch. Traffic from any source port to a target port can be mirrored for real-time analysis.
PAGE 398
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 42-2 enable mirror Description This command is used to enable mirror function without having to modify the mirror session configuration. Format enable mirror Parameters None. Restrictions Only Administrator and Operator-level users can issue this command. Example To enable mirroring function: DES-3200-28/ME:admin#enable mirror Command: enable mirror Success.
PAGE 399
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To disable mirroring function: DES-3200-28/ME:admin#disable mirror Command: disable mirror Success. DES-3200-28/ME:admin# 42-4 show mirror Description This command is used to display the current mirror function state and mirror session configuration on the Switch. Format show mirror Parameters None. Restrictions None.
PAGE 400
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 43 MSTP debug enhancement Command List debug stp config ports [ | all] [event | bpdu | state_machine | all] state [disable | brief | detail] debug stp show information debug stp show flag {ports } debug stp show counter {ports [ | all]} debug stp clear counter {ports[ | all]} debug stp state [enable | disable] 43-1 debug stp config ports Description This command is used to c
PAGE 401
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 43-2 debug stp show information Description This command is used to display STP detailed information, such as the hardware tables, the STP state machine, etc. Format debug stp show information Parameters None. Restrictions Only Administrator-level users can issue this command.
PAGE 402
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 43-3 debug stp show flag Description This command is used to display the STP debug level on specified ports. Format debug stp show flag {ports } Parameters ports - (Optional) Specify the STP ports to display. - (Optional) Enter the list of port used for this configuration here. If no parameter is specified, all ports on the Switch will be displayed.
PAGE 403
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 22 23 24 25 26 27 28 Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled DES-3200-28/ME:admin# 43-4 debug stp show counter Description This command is used to display the STP counters.
PAGE 404
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#debug stp show counter ports 9 Command: debug stp show counter ports 9 STP Counters -------------------------------------Port 9 : Receive: Total STP Packets : 0 Configuration BPDU : 0 TCN BPDU : 0 RSTP TC-Flag : 0 RST BPDU : 0 Discard: Total Discarded BPDU Global STP Disabled Port STP Disabled Invalid packet Format Invalid Protocol Configuration BPDU Length TCN BPDU Length RST BPDU Length Invalid Type Inva
PAGE 405
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#debug stp clear counter ports all Command: debug stp clear counter ports all Success. DES-3200-28/ME:admin# 43-6 debug stp state Description This command is used to enable or disable the STP debug state. Format debug stp state [enable | disable] Parameters state - Specify the STP debug state. enable - Enable the STP debug state. disable - Disable the STP debug state.
PAGE 406
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 44 Multicast Filter Command List create mcast_filter_profile {[ipv4 | ipv6]} profile_id profile_name config mcast_filter_profile [profile_id | profile_name ] {profile_name | [add | delete] }(1) config mcast_filter_profile ipv6 [profile_id | profile_name ] {profile_name | [add | delete]
PAGE 407
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#create mcast_filter_profile profile_id 2 profile_name MOD Command: create mcast_filter_profile profile_id 2 profile_name MOD Success. DES-3200-28/ME:admin# 44-2 config mcast_filter_profile Description This command is used to add or delete a range of multicast IP addresses to or from the profile.
PAGE 408
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config mcast_filter_profile ipv6 [profile_id | profile_name ] {profile_name | [add | delete] }(1) Parameters profile_id - ID of the profile. - Enter the profile ID value here. This value must be between 1 and 24. profile_name - Provides a meaningful description for the profile. - Enter the profile name here.
PAGE 409
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide - Enter the profile ID value here. This value must be between 1 and 24. all - All multicast address profiles will be deleted. profile_name - Specify to display a profile based on the profile name. - Enter the profile name value here. The profile name can be up to 32 characters long. Restrictions Only Administrator, Operator and Power-User level users can issue this command.
PAGE 410
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To display all the defined multicast address profiles: DES-3200-28/ME:admin#show mcast_filter_profile Command: show mcast_filter_profile Profile ID Name ---- ---------------1 MOD Multicast Addresses ---------------- ---------------234.1.1.1 - 238.244.244.244 234.1.1.1 - 238.244.244.244 customer 224.19.62.34 - 224.19.162.
PAGE 411
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To add multicast address profile 2 to ports 1 and 3: DES-3200-28/ME:admin#config limited_multicast_addr ports 1,3 add profile_id 2 Command: config limited_multicast_addr ports 1,3 add profile_id 2 Success.
PAGE 412
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure the maximum number of multicast group that ports 1 and 3 can join to 100: DES-3200-28/ME:admin#config max_mcast_group ports 1, 3 max_group 100 Command: config max_mcast_group ports 1, 3 max_group 100 Success. DES-3200-28/ME:admin# 44-8 show max_mcast_group Description This command is used to display the maximum number of multicast groups that a port can join.
PAGE 413
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide To display the maximum number of multicast groups that VLANs 1 and 2 can join: DES-3200-28/ME:admin#show max_mcast_group vlanid 1-2 Command: show max_mcast_group vlanid 1-2 VLAN -----1 2 Max Multicast Group Number ---------------------------Infinite 10 Action --------Drop Drop Total Entries: 2 DES-3200-28/ME:admin# 44-9 show limited_multicast_addr Description This command is used to display the multicast address range by
PAGE 414
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show limited_multicast_addr ports 1,3 Command: show limited_multicast_addr ports 1,3 Port Access : 1 : Deny Profile ID ----------1 Port Access Name ----------customer Multicast Addresses ---------------------------224.19.62.34 - 224.19.162.200 : 3 : Deny Profile ID ----------1 Name ---------------customer Multicast Addresses ---------------------------224.19.62.34 - 224.19.162.
PAGE 415
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide igmp_query - (Optional) Specify to filter the IGMP query control packets. ospf - (Optional) Specify to filter the OSPF control packets. rip - (Optional) Specify to filter the RIP control packets. vrrp - (Optional) Specify to filter the VRRP control packets. all - Specify to filter all the L3 protocol control packets. state - Specify the filter function status. The default is disabled. enable - Enable the filtering function.
PAGE 416
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show cpu_filter l3_control_pkt ports 1-2 Command: show cpu_filter l3_control_pkt ports 1-2 Port ---1 ed 2 ed IGMP Query ---------Disabled DVMRP -------Enabled PIM -------Disabled Disabled Enabled Disabled DES-3200-28/ME:admin# 412 OSPF RIP VRRP ---------------------Disabled Disabled Disabl Disabled Disabled Disabl
PAGE 417
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 45 Multicast VLAN Command List create igmp_snooping multicast_vlan {remap_priority [ | none] {replace_priority}} config igmp_snooping multicast_vlan {[add | delete] [member_port | [source_port | untag_source_port ] | tag_member_port ] | state [enable|disable] | replace_source_ip | remap_priority [ |
PAGE 418
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide - The VLAN ID of the multicast VLAN to be created. This value must be between 2 and 4094. remap_priority - (Optional) The remap priority (0 to 7) to be associated with the data traffic to be forwarded on the multicast VLAN. If none is specified, the packet’s original priority will be used. The default setting is none. - Enter the remap priority value here. This value must be between 0 and 7.
PAGE 419
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide - Enter the list of port to be configured here. untag_source_port - Specify the source port or range of source ports as untagged members of the multicast VLAN. The PVID of the untagged source port is automatically changed to the multicast VLAN. Source ports must be either tagged or untagged for any single multicast VLAN, i.e. both types cannot be members of the same multicast VLAN.
PAGE 420
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide to 32 characters long. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To create an IGMP snooping multicast group profile with the name “test”: DES-3200-28/ME:admin#create igmp_snooping multicast_vlan_group_profile test Command: create igmp_snooping multicast_vlan_group_profile test Success.
PAGE 421
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config igmp_snooping multicast_vlan_group_profile test add 225.1.1.1 Command: config igmp_snooping multicast_vlan_group_profile test add 225.1.1.1 Success. DES-3200-28/ME:admin# 45-5 delete igmp_snooping multicast_vlan_group_profile Description This command is used to delete an IGMP snooping multicast group profile on the Switch. Specify a profile name to delete it.
PAGE 422
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters - (Optional) Enter the multicast VLAN group profile name here. The name can be up to 32 characters long. Restrictions None.
PAGE 423
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters - Enter the multicast VLAN name here. The VLAN name can be up to 32 characters long. add - Used to associate a profile to a multicast VLAN. delete - Used to de-associate a profile from a multicast VLAN. profile_name - Specify the multicast VLAN profile name. - Enter the multicast VLAN profile name here. The name can be up to 32 characters long.
PAGE 424
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show igmp_snooping multicast_vlan_group Command: show igmp_snooping multicast_vlan_group VLAN Name ------------------------------mv1 VLAN ID ------2 Multicast Group Profiles --------------------------------test DES-3200-28/ME:admin# 45-9 delete igmp_snooping multicast_vlan Description This command is used to delete an IGMP snooping multicast VLAN.
PAGE 425
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions Only Administrator-level users can issue this command. Example To enable the IGMP snooping multicast VLAN function globally: DES-3200-28/ME:admin#enable igmp_snooping multicast_vlan Command: enable igmp_snooping multicast_vlan Success. DES-3200-28/ME:admin# 45-11 disable igmp_snooping multicast_vlan Description This command is used to disable the IGMP multicast VLAN function.
PAGE 426
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 45-12 config igmp_snooping multicast_vlan forward_unmatched Description This command is used to configure the forwarding mode for multicast VLAN unmatched packets. When the Switch receives an IGMP snooping packet, it will match the packet against the multicast profile to determine which multicast VLAN to associate with. If the packet does not match all profiles, the packet will be forwarded or dropped based on this setting.
PAGE 427
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions None.
PAGE 428
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 46 Multiple Spanning Tree Protocol (MSTP) Command List enable stp disable stp config stp {maxage | maxhops | hellotime | forwarddelay | txholdcount | fbpdu [enable | disable] | nni_bpdu_addr [dot1d | dot1ad]} show stp create stp instance_id config stp instance_id [add_vlan | remove_vlan] delete stp instance_id
PAGE 429
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#enable stp Command: enable stp Success. DES-3200-28/ME:admin# 46-2 disable stp Description This command is used to disable STP globally. Format disable stp Parameters None. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To disable STP: DES-3200-28/ME:admin#disable stp Command: disable stp Success.
PAGE 430
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide - Enter the maximum age value here. This value must be between 6-40. maxhops - (Optional) Used to restrict the forwarded times of one BPDU. The default value is 20. - Enter the maximum hops value here. This value must be between 6 and 40. hello_time - (Optional) The time interval for sending configuration BPDUs by the Root Bridge. The default value is 2 seconds.
PAGE 431
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions None.
PAGE 432
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#create stp instance_id 2 Command: create stp instance_id 2 Success. DES-3200-28/ME:admin# 46-6 config stp instance_id Description This command is used to map or remove the VLAN range of the specified MST instance for the existed MST instances. Format config stp instance_id [add_vlan | remove_vlan] Parameters instance_id - Specify the MSTP instance ID.
PAGE 433
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 46-7 delete stp instance_id Description This command is used to delete an MST Instance. Format delete stp instance_id Parameters instance_id - Specify the MSTP instance ID. Instance 0 represents for default instance, CIST. - Enter the MSTP instance ID here. This value must be between 1 and 7. Restrictions Only Administrator, Operator and Power-User level users can issue this command.
PAGE 434
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To change the name and revision level of the MST configuration identification: DES-3200-28/ME:admin#config stp mst_config_id name R&D_BlockG revision_level 1 Commands: config stp mst_config_id name R&D_BlockG revision_level 1 Success. DES-3200-28/ME:admin# 46-9 show stp mst_config_id Description This command is used to show the MST configuration identification. Format show stp mst_config_id Parameters None.
PAGE 435
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config stp mst_ports instance_id {internalCost [auto | ] | priority } Parameters mst_ports - Specify to be distinguished from the parameters of ports only at CIST level. - Enter a list of ports used for the configuration here. instance_id - Specify the instance ID used. - Enter the instance ID used here. This value must be between 0 and 7.
PAGE 436
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide hellotime - (Optional) The default value is 2 . This parameter is for MSTP version. For STP and RSTP version, uses the per system hellotime parameter. - Enter the hello time value here. This value must be between 1 and 2. migrate - (Optional) Operation of management in order to specify the port to send MSTP BPDU for a delay time. yes - Specify that the MSTP BPDU for a delay time will be sent.
PAGE 437
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format show stp ports {} Parameters ports - To show parameters of the designated port numbers, to be distinguished from showing parameters of the bridge. - (Optional) Enter a list of ports used for the configuration here. Restrictions None.
PAGE 438
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters priority - Specify the bridge priority value. This value must be divisible by 4096. - Enter the bridge priority value here. This value must be between 0 and 61440. instance_id - Identifier to distinguish different STP instances. - Enter the STP instance ID here. This value must be between 0 and 7.
PAGE 439
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide To config STP version with the same value of old configuration: DES-3200-28/ME:admin#config stp version mstp Command: config stp version mstp Configure value is the same with current value. Success. DES-3200-28/ME:admin# 46-15 show stp instance Description This command is used to display each instance parameters settings. Value means the instance ID, if there is no input of this value, all instance will be shown.
PAGE 440
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show stp instance Command: show stp instance STP Instance Settings --------------------------Instance Type : CIST Instance Status : Enabled Instance Priority : 32768(bridge priority : 32768, sys ID ext : 0 ) STP Instance Operational Status -------------------------------Designated Root Bridge : 32768/00-22-22-22-22-00 External Root Cost : 0 Regional Root Bridge : 32768/00-22-22-22-22-00 Internal Root Cost
PAGE 441
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 47 Network Load Balancing (NLB) Command List create nlb unicast_fdb config nlb unicast_fdb [add|delete] delete nlb unicast_fdb create nlb multicast_fdb [ | vlanid ] config nlb multicast_fdb [ | vlanid ] [add | delete] delete nlb multicast_fdb [ | vlanid ] show nlb fdb 47-1
PAGE 442
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 47-2 config nlb unicast_fdb Description This command is used to add or delete the forwarding ports for the specified NLB unicast FDB entry. Format config nlb unicast_fdb [add|delete] Parameters - Specify the MAC address of the NLB unicast FDB entry to be configured. add - Specify to add the ports. delete - Specify to delete the ports.
PAGE 443
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To delete the NLB unicast FDB entry, for the product that support the VLAN information on the unicast forwarding: DES-3200-28/ME:admin#delete nlb unicast_fdb 02-bf-01-01-01-01 Command: delete nlb unicast_fdb 02-BF-01-01-01-01 Success. DES-3200-28/ME:admin# 47-4 create nlb multicast_fdb Description This command is used to create a NLB multicast FDB entry.
PAGE 444
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config nlb multicast_fdb [ | vlanid ] [add | delete] Parameters - Specify the VLAN of the NLB multicast FDB entry to be configured. vlanid - Specify the VLAN by the VLAN ID. - Enter the VLAN ID here. - Specify the Mac address of the NLB multicast FDB entry to be configured. add - Specify a list of forwarding ports to be added.
PAGE 445
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To delete NLB multicast FDB entry: DES-3200-28/ME:admin#delete nlb multicast_fdb default 03-bf-01-01-01-01 Command: delete nlb multicast_fdb default 03-bf-01-01-01-01 Success. DES-3200-28/ME:admin# 47-7 show nlb fdb Description This command is used to show the NLB Configured entry. Format show nlb fdb Parameters None. Restrictions None.
PAGE 446
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 48 Network Monitoring Command List show packet ports show error ports show utilization [cpu | ports] show utilization dram show utilization flash clear counters {ports } 48-1 show packet ports Description This command is used to display statistics about the packets sent and received by the Switch.
PAGE 447
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show packet ports 7 Command: show packet ports 7 Port Number : 7 ================================================================== Frame Size/Type Frame Counts Frames/sec ---------------------------------------------64 0 0 65-127 0 0 128-255 0 0 256-511 0 0 512-1023 0 0 1024-1518 0 0 Unicast RX 0 0 Multicast RX 0 0 Broadcast RX 0 0 Frame Type --------------RX Bytes RX Frames TX Bytes TX Frames Total ----
PAGE 448
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show error ports 3 Command: show error ports 3 Port Number : 3 CRC Error Undersize Oversize Fragment Jabber Drop Pkts Symbol Error RX Frames --------0 0 0 0 0 0 0 Excessive Deferral CRC Error Late Collision Excessive Collision Single Collision Collision TX Frames --------0 0 0 0 0 0 CTRL+C ESC q Quit SPACE n Next Page p Previous Page r Refresh 48-3 show utilization Description This command is used
PAGE 449
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show utilization ports Command: show utilization ports Port TX/sec RX/sec Util Port ----- ---------- ---------- -------1 0 0 0 21 2 0 0 0 22 3 0 0 0 23 4 0 0 0 24 5 0 0 0 25 6 0 0 0 26 7 0 0 0 27 8 0 0 0 28 9 0 0 0 10 0 0 0 11 0 0 0 12 0 0 0 13 0 0 0 14 0 0 0 15 0 0 0 16 0 0 0 17 0 0 0 18 0 0 0 19 0 0 0 20 0 0 0 CTRL+C ESC q Quit SPACE n Next Page p Previous To display the CPU utilization: 445 TX/sec --
PAGE 450
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show utilization cpu Command: show utilization cpu CPU Utilization ------------------------------------------------------------------------------Five seconds - 10 % One minute - 10 % Five minutes - 10 % CTRL+C ESC q Quit SPACE n Next Page p Previous Page r Refresh 48-4 show utilization dram Description This command is used to show DRAM memory utilization. Format show utilization dram Parameters None.
PAGE 451
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show utilization dram Command: show utilization dram DRAM Utilization : Total DRAM Used DRAM Utilization : 131072 : 115758 : 88 % KB KB CTRL+C ESC q Quit SPACE n Next Page p Previous Page r Refresh 48-5 show utilization flash Description This command is used to show the flash memory utilization. Format show utilization flash Parameters None. Restrictions None.
PAGE 452
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format clear counters {ports } Parameters ports - (Optional) Specify a range of ports to be configured. The port list is specified by listing the lowest switch number and the beginning port number on that switch, separated by a colon. Then highest switch number, and the highest port number of the range (also separeted by a colon) are specified. The beginning and end of the port list range are seperated by a dash.
PAGE 453
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 49 OAM Commands config ethernet_oam ports [ | all ] [mode [active | passive] | state [enable | disable] | link_monitor [error_symbol {threshold | window | notify_state [enable | disable]}(1) | error_frame {threshold | window | notify_state [enable | disable]}(1) | error_frame_seconds {threshold | window
PAGE 454
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config ethernet_oam ports [ | all ] [mode [active | passive] | state [enable | disable] | link_monitor [error_symbol {threshold | window | notify_state [enable | disable]}(1) | error_frame {threshold | window | notify_state [enable | disable]}(1) | error_frame_seconds {threshold | window
PAGE 455
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide critical_link_event –Specify critical link event. dying_gasp - An unrecoverable local failure condition has occurred. critical_event - An unspecified critical event has occurred. notify_state - Specify the event notification status. The default state is enable. enable - Specify to enable event notification. disable - Specify to disable event notification. remote_loopback - Specify remote loop.
PAGE 456
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config ethernet_oam ports 1 link_monitor error_frame threshold 2 window 1000 notify_state enable Command: config ethernet_oam ports 1 link_monitor error_frame threshold 2 window 1000 notify_state enable Success.
PAGE 457
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config ethernet_oam ports 1 received_remote_loopback process Command: config ethernet_oam ports 1 received_remote_loopback process Success. DES-3200-28/ME:admin# 49-2 show ethernet_oam ports Description This command is used to display Ethernet OAM information, including status, configuration, statistics, and event log, on specified ports.
PAGE 458
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 4. Variable: It indicates that the OAM entity can send and receive variable requests to monitor the attribute value as described in the IEEE 802.3 Clause 30 MIB. The event log displays Ethernet OAM event log information. The switch can buffer 1000 event logs. The event log is different from sys-log as it provides more detailed information than sys-log. Each OAM event will be recorded in both OAM event log and syslog.
PAGE 459
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show ethernet_oam ports 1 statistics Command: show ethernet_oam ports 1 statistics Port 1 -----------------------------------------------------------Information OAMPDU TX : 0 Information OAMPDU RX : 0 Unique Event Notification OAMPDU TX : 0 Unique Event Notification OAMPDU RX : 0 Duplicate Event Notification OAMPDU TX: 0 Duplicate Event Notification OAMPDU RX: 0 Loopback Control OAMPDU TX : 0 Loopback Cont
PAGE 460
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#clear ethernet_oam ports 1 statistics Command: clear ethernet_oam ports 1 statistics Success. DES-3200-28/ME:admin# To clear port 1 OAM events: DES-3200-28/ME:admin#clear ethernet_oam ports 1 event_log Command: clear ethernet_oam ports 1 event_log Success.
PAGE 461
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 50 Peripherals Command List show device_status show environment config temperature threshold {high | low } config temperature [trap | log] state [enable | disable] config external_alarm channel message show external_alarm 50-1 show device_status Description This command is used to display the current status of the power and fan(s) on the sys
PAGE 462
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 50-2 show environment Description This command is used to display current status of power(s) and fan(s) on the system. Format show environment Parameters None. Restrictions None.
PAGE 463
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide - Enter the high threshold temperature. low - (Optional) To configure low threshold value. - Enter the low threshold temperature. Restrictions Only Administrator and Operator-level users can issue this command. Example To configure the warning temperature threshold: DES-3200-28/ME:admin#config temperature threshold high 80 Command: config temperature threshold high 80 Success.
PAGE 464
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 50-5 config external alarm Purpose Used to configure the external alarm messege for each channel. Description The config external alarm command is used to configure the external alarm message for each channel on the switch.
PAGE 465
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 50-6 show external alarm Purpose Used to display the external alarm message for each channel. Description The show external_alarm command is used to display the external alarm message configured for each channel. Format show external_alarm Parameters None Help Message Show external alarm configuration and status.
PAGE 466
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 51 Ping Command List ping {times | timeout } ping6 {times | size | timeout } 51-1 ping Description This command is used to send Internet Control Message Protocol (ICMP) echo messages to a remote IP address. The remote IP address will then “echo” or return the message.
PAGE 467
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 51-2 ping6 Description This command is used to send IPv6 Internet Control Message Protocol (ICMP) echo messages to a remote IPv6 address. The remote IPv6 address will then “echo” or return the message. This is used to confirm the IPv6 connectivity between the Switch and the remote device.
PAGE 468
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 52 Port Security Command List config port_security system max_learning_addr [ | no_limit] config port_security ports [ | all] [{admin_state [enable | disable] | max_learning_addr | lock_address_mode [permanent | deleteontimeout | deleteonreset]} (1)| {vlan [ | vlanid ] max_learning_addr [ | no_limit]}(1)] config port_securit
PAGE 469
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config port_security system max_learning_addr 256 Command: config port_security system max_learning_addr 256 Success. DES-3200-28/ME:admin# 52-2 config port_security ports Description This command is used to configure the admin state, the maximum number of addresses that can be learnt and the lock address mode.
PAGE 470
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command.
PAGE 471
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config port_security vlan vlanid 1 max_learning_addr 64 Command: config port_security vlan vlanid 1 max_learning_addr 64 Success. DES-3200-28/ME:admin# 52-4 delete port_security_entry Description This command is used to delete a port security entry. Format delete port_security_entry [vlan | vlanid ] mac_address Parameters vlan - Specify the VLAN by VLAN name.
PAGE 472
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters ports - (Optional) Specify the range of ports to be configured. - The port security entries learned on the specified port will be cleared. all - All the port security entries learned by the system will be cleared. vlan - (Optional) The port security entries learned on the specified VLANs will be cleared. - Enter the VLAN name here. This name can be up to 32 characters long.
PAGE 473
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To show all the port security entries: DES-3200-28/ME:admin#show port_security_entry Command: show port_security_entry MAC Address ----------------00-00-00-00-00-01 VID Port Lock Mode ---- ----- --------------1 25 DeleteOnTimeout Total Entries: 1 DES-3200-28/ME:admin# 52-7 show port_security Description This command is used to display the port security related information, including state, maximum learned addresse
PAGE 474
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show port_security Command: show port_security Port Security Trap/Log System Maximum Address : Disabled : 256 VLAN Configuration (Only VLANs with limitation are displayed) VID VLAN Name Max. Learning Addr. ---- -------------------------------- -----------------1 default 64 DES-3200-28/ME:admin# 52-8 enable port_security trap_log Description This command is used to enable port security traps/logs.
PAGE 475
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format disable port_security trap_log Parameters None. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To prevent a port security trap from being sent from the switch: DES-3200-28/ME:admin#disable port_security trap_log Command: disable port_security trap_log Success.
PAGE 476
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 53 Power over Ethernet (PoE) Command List (DES-320028P and DES-3200-52P Only) config poe system {power_limit | power_disconnect_method [deny_next_port | deny_low_priority_port] | legacy_pd [enable | disable]} (DES-3200-28P Only) config poe system {power_limit | power_disconnect_method [deny_next_port | deny_low_priority_port] | legacy_pd [enable | disable]} (DES-3200-52P Only) config poe
PAGE 477
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide disconnect_method is set to deny_low_priority_port, then the power provision can utilize the system’s maximum power. legacy_pd - Configure legacy PDs detection status, enable for support, if set to disable, can’t detect legacy PDs signal. enable - Specify that the legacy PDs detection status will be enabled. disable - Specify that the legacy PDs detection status will be disabled.
PAGE 478
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters ports - Specify the list of ports whose setting is under configuration. all - Specify that all the ports will be included in this configuration. - Enter the list of port used for this configuration here. state - (Optional) When the state is set to disable, power will not be supplied to the powered device connected to this port. enable - Specify that state will be enabled.
PAGE 479
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config poe ports 1-4 state enable priority critical power_li mit class_1 Command: config poe ports 1-4 state enable priority critical power_limit class_1 Success. DES-3200-28/ME:admin#config poe ports 5 state enable priority critical power_lim it user_define 1000 Command: config poe ports 5 state enable priority critical power_limit user_define 1000 Success.
PAGE 480
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show poe system Command: show poe system PoE System Information --------------------------------------------------Power Limit : 188(Watts) Power Consumption : 0(Watts) Power Remained : 169(Watts) Power Disconnection Method : Deny Next Port Detection Legacy PD : Disabled If Power Disconnection Method is set to deny next port, then the system can not utilize out of its maximum power capacity.
PAGE 481
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show poe ports 1-6 Command: show poe ports 1-6 Port State Priority Power Limit(mW) Time Range Class Power(mW) Voltage(decivolt) Current(mA) Status =============================================================================== 1 Enabled Low 16200(Class 0) 0 0 0 0 OFF : Interim state during line detection 2 Enabled Low 16200(Class 0) 0 0 0 0 OFF : Interim state during line detection 3 Enabled Low 16200(Cla
PAGE 482
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 54 PPPoE Circuit ID Insertions Command List config pppoe circuit_id_insertion state [enable | disable] config pppoe circuit_id_insertion ports {state [enable | disable] | circuit_id [mac | ip | udf ]}(1) show pppoe circuit_id_insertion show pppoe circuit_id_insertion ports {} 54-1 config pppoe circuit_id_insertion state Description This command is used to enable or disable PPPoE cir
PAGE 483
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 54-2 config pppoe circuit_id_insertion ports Description This command is used to configure port’s PPPoE Circuit ID insertion function. When the port’s state and the global state are enabled, the system will insert the Circuit ID TAG to the received PPPoE discovery initiation and request packet if the TAG is absent, and remove the Circuit ID TAG from the received PPPoE offer and session confirmation packet.
PAGE 484
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions None. Example To display PPPoE circuit ID insertion status: DES-3200-28/ME:admin#show pppoe circuit_id_insertion Command: show pppoe circuit_id_insertion Global PPPoE State: Enabled DES-3200-28/ME:admin# 54-4 show pppoe circuit_id_insertion ports Description This command is used to display Switch’s port PPPoE Circuit ID insertion configuration.
PAGE 485
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show pppoe circuit_id_insertion ports Command: show pppoe circuit_id_insertion ports 2-5 Port ---2 3 4 5 State -------Enabled Enabled Enabled Enabled Circuit ID --------------------------------------------Switch IP Switch IP Switch IP Switch IP DES-3200-28/ME:admin# 481 2-5
PAGE 486
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 55 Protocol VLAN Command List create dot1v_protocol_group group_id {group_name } config dot1v_protocol_group [group_id | group_name ] [add protocol [ethernet_2 | ieee802.3_snap | ieee802.3_llc] | delete protocol [ethernet_2 | ieee802.3_snap | ieee802.
PAGE 487
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 55-2 config dot1v_protocol_group add protocol Description This command is used to add a protocol to a protocol group. The selection of a protocol can be a pre-defined protocol type or a user defined protocol. Format config dot1v_protocol_group [group_id | group_name ] [add protocol [ethernet_2 | ieee802.3_snap | ieee802.3_llc] | delete protocol [ethernet_2 | ieee802.3_snap | ieee802.
PAGE 488
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters group_id - Specify the group ID to be deleted. - Enter the group ID used here. group_name - Specify the name of the group to be deleted. - Enter the group name here. This name can be up to 32 characters long. all - Specify that all the protocol group will be deleted. Restrictions Only Administrator, Operator and Power-User level users can issue this command.
PAGE 489
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show dot1v_protocol_group group_id 10 Command: show dot1v_protocol_group group_id 10 Protocol Group ID Protocol Group Name Frame Type Protocol Value ----------------- -------------------------------- -------------- -------------10 General_Group EthernetII 86DD Total Entries: 1 DES-3200-28/ME:admin# 55-5 config port dot1v Description This command is used to assign the VLAN for untagged packets ingress fr
PAGE 490
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example The example is to assign VLAN marketing-1 for untaged ipv6 packet ingress from port 3.
PAGE 491
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show port dot1v ports 1 Command: show port dot1v ports 1 Port: 1 Protocol Group ID ------------------1 2 3 4 VLAN Name --------------------------------default VLAN2 VLAN3 VLAN4 Success.
PAGE 492
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 56 QinQ Command List enable qinq disable qinq config qinq inner_tpid config qinq ports [ | all] {role [uni | nni] | missdrop [enable | disable] | outer_tpid | add_inner_tag [ | disable]} show qinq show qinq inner_tpid show qinq ports {} create vlan_translation ports [ | all] [add cvid | replace cvid ] svid
PAGE 493
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 56-2 disable qinq Description This command is used to disable the QinQ. When QinQ is disabled, all dynamic learned L2 addresses will be cleared, all dynamic registered VLAN entries will be cleared, and GVRP will be disabled. To run GVRP on the Switch, the administrator should enable GVRP manually. Format disable qinq Parameters None.
PAGE 494
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure the inner TPID in the system to 0x9100: DES-3200-28/ME:admin#config qinq inner_tpid 0x9100 Command: config qinq inner_tpid 0x9100 Success. DES-3200-28/ME:admin# 56-4 config qinq ports Description This command is used to configure the QinQ port's parameters.
PAGE 495
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config qinq ports 1-4 role nni outer_tpid 0x88A8 Command: config qinq ports 1-4 role nni outer_tpid 0x88A8 Success. DES-3200-28/ME:admin# 56-5 show qinq Description This command is used to display the global QinQ status. Format show qinq Parameters None. Restrictions None.
PAGE 496
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions None. Example To display the inner-TPID of a system: DES-3200-28/ME:admin#show qinq inner_tpid Command: show qinq inner_tpid Inner TPID: 0x9100 DES-3200-28/ME:admin# 56-7 show qinq ports Description This command is used to display the QinQ configuration of the ports. Format show qinq ports {} Parameters ports - Specify a list of ports to be displayed.
PAGE 497
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show qinq ports 1-2 Command: show qinq ports 1-2 Port ID: 1 --------------------------------------------------------Role: NNI Miss Drop: Disabled Outer Tpid: 0x8100 Add Inner Tag: Disabled Port ID: 2 --------------------------------------------------------Role: NNI Miss Drop: Disabled Outer Tpid: 0x8100 Add Inner Tag: Disabled DES-3200-28/ME:admin# 56-8 create vlan_translation ports Description This co
PAGE 498
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To replace the C-Tag in which the CVID is 20, with the S-Tag and the S-VID is 200 at UNI Port 1: DES-3200-28/ME:admin#create vlan_translation ports 1 replace cvid 20 svid 200 Command: create vlan_translation ports 1 replace cvid 20 svid 200 Success.
PAGE 499
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#delete vlan_translation ports 1-4 Command: delete vlan_translation ports 1-4 Success. DES-3200-28/ME:admin# 56-10 show vlan_translation Description This command is used to display the existing C-VLAN-based VLAN translation rules. Format show vlan_translation {[ports | cvid ]} Parameters ports – (Optional) Specify a list of ports to be displayed.
PAGE 500
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 57 Quality of Service (QoS) Command List config bandwidth_control [ | all] {rx_rate [no_limit | ] | tx_rate [ no_limit | ]} show bandwidth_control {} config per_queue bandwidth_control {ports [ | all]} {{min_rate [no_limit | ]} max_rate [no_limit | ]} show per_queue bandwidth_control {} co
PAGE 501
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide command is executed. - Enter the transmitting data rate here. This value must be between 64 and 1024000. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To configure the port bandwidth: DES-3200-28/ME:admin#config bandwidth_control 1-10 tx_rate 100 Command: config bandwidth_control 1-10 tx_rate 100 Granularity: RX: 64, TX: 64. Actual Rate: TX: 64.
PAGE 502
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show bandwidth_control 1-10 Command: show bandwidth_control 1-10 Bandwidth Control Table Port ----1 2 3 4 5 6 7 8 9 10 RX Rate (Kbit/sec) ---------No Limit No Limit No Limit No Limit No Limit No Limit No Limit No Limit No Limit No Limit TX Rate (Kbit/sec) ---------64 64 64 64 64 64 64 64 64 64 Effective RX (Kbit/sec) ---------------No Limit No Limit No Limit No Limit No Limit No Limit No Limit No Limit
PAGE 503
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide receive. If the specified rate is not multiple of minimum granularity, the rate will be adjusted. Restrictions Only Administrator level can issue this command.
PAGE 504
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show per_queue bandwidth_control 10 Command: show per_queue bandwidth_control 10 Queue Bandwidth Control Table On Port: 10 Queue 0 1 2 3 4 5 6 7 Min Rate(Kbit/sec) 640 640 640 640 No Limit No Limit No Limit No Limit Max Rate(Kbit/sec) No Limit No Limit No Limit No Limit No Limit No Limit No Limit No Limit DES-3200-28/ME:admin# 57-5 config scheduling Description This command is used to configure the t
PAGE 505
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 57-6 config scheduling_mechanism Description This command is used to configure the traffic scheduling mechanism for each CoS queue. Format config scheduling_mechanism {ports [ | all]} [strict | wrr] Parameters ports - (Optional) Specify a range of ports to be configured. - Enter the list of port used for this configuration here. all - For set all ports in the system, you may use “all” parameter.
PAGE 506
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters - (Optional) Specify a range of ports to be displayed. If no parameter specified, system will display all ports scheduling configurations. Restrictions None.
PAGE 507
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To show scheduling mechanism: DES-3200-28/ME:admin#show scheduling_mechanism Command: show scheduling_mechanism Port ----1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Mode -----Strict Strict Strict Strict Strict Strict Strict Strict Strict Strict Strict Strict Strict Strict Strict Strict Strict Strict Strict Strict Strict Strict Strict Strict Strict Strict Strict Strict DES-3200-28/ME:adm
PAGE 508
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters - The 802.1p user priority you want to associate with the (the number of the hardware queue) with. - The number of the Switch’s hardware priority queue. The switch has 8 hardware priority queues available. They are numbered between 0 (the lowest priority) and 7 (the highest priority).
PAGE 509
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show 802.1p user_priority Command: show 802.1p user_priority QOS Class of Traffic: Priority-0 -> Priority-1 -> Priority-2 -> Priority-3 -> Priority-4 -> Priority-5 -> Priority-6 -> Priority-7 -> DES-3200-28/ME:admin# 57-11 config 802.1p default_priority Description This command is used to configure the 802.
PAGE 510
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 57-12 show 802.1p default_priority Description This command is used to display the current configured default priority settings on the Switch. The default priority can also be assigned by the RADIUS server through the authentication process. The authentication with the RADIUS sever can be per port or port user. For per port authentication, the priority assigned by RADIUS server will be the effective port default priority.
PAGE 511
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 57-13 config dscp trust Description This command is used to configure the state of DSCP trust per port. When DSCP is not trusted, 802.1p is trusted. Format config dscp trust [ | all] state [enable | disable] Parameters - Enter the list of port used for this configuration. all - Specify that the command apply to all ports on the Switch. state - Enable or disable to trust DSCP.
PAGE 512
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide green - Specify green as the mapped color. red - Specify red as the mapped color. yellow - Specify yellow as the mapped color. Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example If a product supports per-port 802.1p mapping configuration, configure the mapping of 802.1p priority 1 to red on ports 1-8. DES-3200-28/ME:admin#config 802.
PAGE 513
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 57-16 show dscp trust Description This command is used to display DSCP trust state for the specified ports on the Switch. Format show dscp trust {} Parameters - (Optional) A range of ports to display. If not specify the port, all ports for DSCP trust status on the Switch will be displayed. Restrictions None. Example Display DSCP trust status on ports 1-8.
PAGE 514
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide These DSCP mapping will take effect at the same time when IP packet ingress from a DSCPtrusted port. Format config dscp map {[ | all]} [dscp_priority to | dscp_dscp to | dscp_color to [green | red | yellow]] Parameters - Enter the list of port used for this configuration here.
PAGE 515
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 57-18 show dscp map Description This command is used to show DSCP trusted port list and mapped color, priority and DSCP. Format show dscp map {} [dscp_priority | dscp_dscp | dscp_color] {dscp } Parameters - (Optional) A range of ports to show. If no parameter is specified, all ports’ dscp mapping will be displayed.
PAGE 516
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 58 Safeguard Engine Command List config safeguard_engine {state [enable | disable]| utilization {rising <20-100> | falling <20-100>} | trap_log [enable | disable] | mode [strict | fuzzy]} show safeguard_engine 58-1 config safeguard_engine Description This command is used to configure the CPU protection control for the system.
PAGE 517
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure CPU protection: DES-3200-28/ME:admin#config safeguard_engine state enable utilization rising 50 falling 30 trap_log enable Command: config safeguard_engine state enable utilization rising 50 falling 30 trap_log enable Success. DES-3200-28/ME:admin# 58-2 show safeguard_engine Description This command is used to show safeguard engine information. Format show safeguard_engine Parameters None.
PAGE 518
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 59 Secure Shell (SSH) Command List config ssh algorithm [3DES | AES128 | AES192 | AES256 | arcfour | blowfish | cast128 | twofish128 | twofish192 | twofish256 | MD5| SHA1 | RSA | DSA] [enable | disable] show ssh algorithm config ssh authmode [password | publickey | hostbased] [enable | disable] show ssh authmode config ssh user authmode [hostbased [hostname | hostname_IP
PAGE 519
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To enable SSH server public key algorithm: DES-3200-28/ME:admin#config ssh algorithm DSA enable Command: config ssh algorithm DSA enable Success. DES-3200-28/ME:admin# 59-2 show ssh algorithm Description This command is used to show the SSH service algorithm. Format show ssh algorithm Parameters None. Restrictions None.
PAGE 520
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show ssh algorithm Command: show ssh algorithm Encryption Algorithm -------------------------3DES : Enabled AES128 : Enabled AES192 : Enabled AES256 : Enabled Arcfour : Enabled Blowfish : Enabled Cast128 : Enabled Twofish128 : Enabled Twofish192 : Enabled Twofish256 : Enabled Data Integrity Algorithm -------------------------MD5 : Enabled SHA1 : Enabled Public Key Algorithm -------------------------RSA : E
PAGE 521
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure user authentication method: DES-3200-28/ME:admin#config ssh authmode publickey enable Command: config ssh authmode publickey enable Success. DES-3200-28/ME:admin# 59-4 show ssh authmode Description This command is used to show the user authentication method. Format show ssh authmode Parameters None. Restrictions None.
PAGE 522
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config ssh user authmode [hostbased [hostname | hostname_IP ] | password | publickey] Parameters - Enter the user name used here. This name can be up to 15 characters long. automode - Specify user authentication method. hostbased - Specify as host-based method. hostname - Specify host domain name. - Enter the domain name here.
PAGE 523
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To show user information about SSH configuration: DES-3200-28/ME:admin#show ssh user authmode Command: show ssh user authmode Current Accounts Username AuthMode ------------- ------------test Public Key alpha Host-based beta Host-based Total Entries : 3 HostName ------------ HostIP ------------- alpha-local beta-local 172.18.61.
PAGE 524
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure SSH server maximum session number is 3: DES-3200-28/ME:admin#config ssh server maxsession 3 Command: config ssh server maxsession 3 Success. DES-3200-28/ME:admin# 59-8 enable ssh Description This command is used to enable SSH server services. Format enable ssh Parameters None. Restrictions Only Administrator, Operator and Power-User level users can issue this command.
PAGE 525
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To disable the SSH server services: DES-3200-28/ME:admin#disable ssh Command: disable ssh Success. DES-3200-28/ME:admin# 59-10 show ssh server Description This command is used to show the SSH server general information. Format show ssh server Parameters None. Restrictions None.
PAGE 526
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 60 Secure Sockets Layer (SSL) Command List download ssl certificate { certfilename keyfilename } enable ssl {ciphersuite {RSA_with_RC4_128_MD5 | RSA_with_3DES_EDE_CBC_SHA | DHE_DSS_with_3DES_EDE_CBC_SHA | RSA_EXPORT_with_RC4_40_MD5}} disable ssl {ciphersuite {RSA_with_RC4_128_MD5 | RSA_with_3DES_EDE_CBC_SHA | DHE_DSS_with_3DES_EDE_CBC_SHA | RSA_EXPORT_with_RC4_40_MD5}} sho
PAGE 527
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#download ssl certificate 10.55.47.1 certfilename cert.der keyfilename pkey.der Command: download ssl certificate 10.55.47.1 certfilename cert.der keyfilename pkey.der Success. DES-3200-28/ME:admin# 60-2 enable ssl Description This command is used to enable SSL status and it’s ciphersuites. Using “enable ssl” command will enable SSL feature which means enable SSLv3 and TLSv1.
PAGE 528
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#enable ssl Command: enable ssl Success. DES-3200-28/ME:admin# Note: Web will be disabled when SSL is enabled. 60-3 disable ssl Description This command is used to disable SSL feature and supported ciphercuites. Using “disable ssl” command will disable SSL feature and for each ciphersuites status user must specified it by this command.
PAGE 529
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#disable ssl Command: disable ssl Success. DES-3200-28/ME:admin# 60-4 show ssl Description This command is used to display the certificate status. User must download specified certificate type according to desired key exchange algorithm.
PAGE 530
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 60-5 show ssl cachetimeout Description This command is used to show cahce timeout value which is designed for dlktimer library to remove the session id after expired. In order to support the resume session feature, the SSL library keep the session id in web server, and invoking the dlktimer library to remove this session id by cache timeout value. Format show ssl cachetimeout Parameters None. Restrictions None.
PAGE 531
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To configure the SSL cache timeout value to 60: DES-3200-28/ME:admin#config ssl cachetimeout 60 Commands: config ssl cachetimeout 60 Success.
PAGE 532
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 61 Show Technical Support Command List show tech_support upload tech_support_toTFTP { } 61-1 show tech_support Description This command is especially used by the technical support personnel to dump the device overall operation information.
PAGE 533
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show tech_support Command: show tech_support #-----------------------------------------------------------------------------# DES-3200-28/ME Fast Ethernet Switch # Technical Support Information # # Firmware: Build 4.04.004 # Copyright(C) 2011 D-Link Corporation. All rights reserved.
PAGE 534
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format upload tech_support_toTFTP { } Parameters - (Optional) Specify the IP address of TFTP server. - Specify the file name to store the information of technique’s support in TFTP server. The max size of the file name is 64. Restrictions Only Administrator and Operator-level users can issue this command.
PAGE 535
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 62 Simple Mail Transfer Protocol (SMTP) Command List enable smtp disable smtp config smtp {server | server_port | self_mail_addr | [add mail_receiver | delete mail_receiver ]}(1) show smtp smtp send_testmsg 62-1 enable smtp Description This command is used to enable the SMTP status. Format enable smtp Parameters None.
PAGE 536
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format disable smtp Parameters None. Restrictions Only Administrator-level users can issue this command. Example To disable SMTP status: DES-3200-28/ME:admin#disable smtp Command: disable smtp Success. DES-3200-28/ME:admin# 62-3 config smtp Description This command is used to configure SMTP settings.
PAGE 537
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure a SMTP server IP address: DES-3200-28/ME:admin#config smtp server 172.18.208.9 Command: config smtp server 172.18.208.9 Success. DES-3200-28/ME:admin# To configure an SMTP server port: DES-3200-28/ME:admin#config smtp server_port 25 Command: config smtp server_port 25 Success. DES-3200-28/ME:admin# To configure a mail source address: DES-3200-28/ME:admin#config smtp self_mail_addr mail@dlink.
PAGE 538
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format show smtp Parameters None. Restrictions None. Example To display the current SMTP information: DES-3200-28/ME:admin#show smtp Command: show smtp SMTP SMTP SMTP Self Status Server Address Server Port Mail Address Index ----1 2 3 4 5 6 7 8 : : : : Disabled 172.18.208.9 25 mail@dlink.com Mail Receiver Address ----------------------------------------------------------------------receiver@dlink.
PAGE 539
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator-level users can issue this command. Example To test whether the SMTP server can be reached: DES-3200-28/ME:admin#smtp send_testmsg Command: smtp send_testmsg Subject:e-mail heading Content:e-mail content Sending mail, please wait... Success.
PAGE 540
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 63 Simple Network Management Protocol (SNMP) Command List create snmp community view [read_only | read_write] delete snmp community show snmp community {} create snmp user {encrypted [by_password auth [md5 | sha ] priv [none | des ] | by_key auth [m
PAGE 541
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide An access list of IP addresses of the SNMP managers that are permitted to use the community string to gain access to the agent. A MIB view, which defines the subset of all MIB objects accessible to the given community. Read and write or read-only permission for the MIB objects accessible to the community.
PAGE 542
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters community - Community string will be deleted. - Enter the community string value here. This value can be up to 32 characters long. Restrictions Only Administrator-level users can issue this command. Example To delete a SNMP community “System”: DES-3200-28/ME:admin#delete snmp community System Command: delete snmp community System Success.
PAGE 543
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show snmp community Command: show snmp community SNMP Community Table Community Name ------------------------------private public View Name ---------------------CommunityView CommunityView Access Right -----------read_write read_only Total Entries : 2 DES-3200-28/ME:admin# 63-4 create snmp user Description This command is used to create a new user to an SNMP group originated by this command.
PAGE 544
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide des - Specify that the DES encryption will be used for the privacy key. - Enter the DES privacy key here. This value must be 32 characters long. Restrictions Only Administrator-level users can issue this command.
PAGE 545
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 63-6 show snmp user Description This command is used to display information on each SNMP username in the group username table. Format show snmp user Parameters None. Restrictions None.
PAGE 546
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide v2c - The second least secure of the possible security models. v3 - The most secure of the possible. noauth_nopriv - Neither support packet authentication nor encrypting. auth_nopriv - Support packet authentication. auth_priv - Support packet authentication and encrypting. read_view - (Optional) Specify that the view name would be read. - Enter the read view name here. This name can be up to 32 characters long.
PAGE 547
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#delete snmp group group123 Command: delete snmp group group123 Success. DES-3200-28/ME:admin# 63-9 show snmp groups Description This command is used to display the names of groups on the Switch and the security model, level, the status of the different views. Format show snmp groups Parameters None. Restrictions None.
PAGE 548
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show snmp groups Command: show snmp groups Vacm Access Table Settings Group Name : public ReadView Name : CommunityView WriteView Name : Notify View Name : CommunityView Securiy Model : SNMPv1 Securiy Level : NoAuthNoPriv Group Name : public ReadView Name : CommunityView WriteView Name : Notify View Name : CommunityView Securiy Model : SNMPv2 Securiy Level : NoAuthNoPriv Group Name : initial ReadView Name
PAGE 549
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide - Object-Identified tree, MIB tree. view_type - Specify the access type of the MIB tree in this view. included - Includes for this view. excluded - Excluded for this view. Restrictions Only Administrator-level users can issue this command. Example To create SNMP view “view123”: DES-3200-28/ME:admin#create snmp view view123 1.3.6 view_type included Command: create snmp view view123 1.3.6 view_type included Success.
PAGE 550
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 63-12 show snmp view Description This command is used to display the SNMP view record. Format show snmp view {} Parameters view - (Optional) View name of the user who likes to show. - Enter the view name here. The name can be up to 32 characters long. Restrictions None.
PAGE 551
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters - The IP address of the recipient for which the traps are targeted. v1 - The least secure of the possible security models. v2c - The second least secure of the possible security models. v3 - The most secure of the possible. noauth_nopriv - Neither support packet authentication nor encrypting. auth_nopriv - Support packet authentication. auth_priv - Support packet authentication and encrypting.
PAGE 552
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#delete snmp host 10.0.0.1 Command: delete snmp host 10.0.0.1 Success. DES-3200-28/ME:admin# 63-15 show snmp host Description This command is used to display the recipient for which the traps are targeted. Format show snmp host {} Parameters host - (Optional) The IP address of the recipient for which the traps are targeted. - Enter the IP address used for the configuration here.
PAGE 553
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config snmp engineID Parameters engineID - Identify for the SNMP engine on the Switch. It is octet string type. It accepts the hex number directly. - Enter the SNMP engine ID here. This value must be between 10 and 64. Restrictions Only Administrator-level users can issue this command.
PAGE 554
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show snmp engineID Command: show snmp engineID SNMP Engine ID : 1023457890 DES-3200-28/ME:admin# 63-18 enable snmp Description This command is used to enable the SNMP function. Format enable snmp Parameters None. Restrictions Only Administrator and Operator-level users can issue this command. Example To enable SNMP: DES-3200-28/ME:admin#enable snmp Command: enable snmp Success.
PAGE 555
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator and Operator-level users can issue this command. Example To disable SNMP: DES-3200-28/ME:admin#disable snmp Command: disable snmp Success. DES-3200-28/ME:admin# 63-20 config snmp system_name Description This command is used to configure the name for the Switch. Format config snmp system_name {} Parameters system_name - A maximum of 128 characters is allowed.
PAGE 556
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config snmp system_location {} Parameters system_location - A maximum of 128 characters is allowed. And NULL string is accepted - (Optional) Enter the system location string here. Restrictions Only Administrator and Operator-level users can issue this command.
PAGE 557
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 63-23 enable snmp traps Description This command is used to enable SNMP trap support. Format enable snmp traps Parameters None. Restrictions Only Administrator and Operator-level users can issue this command. Example To enable SNMP trap support: DES-3200-28/ME:admin#enable snmp traps Command: enable snmp traps Success.
PAGE 558
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#disable snmp traps Command: disable snmp traps Success. DES-3200-28/ME:admin# 63-25 enable snmp authenticate_traps Description This command is used to enable SNMP authentication failure trap support. Format enable snmp authenticate_traps Parameters None. Restrictions Only Administrator and Operator-level users can issue this command.
PAGE 559
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator and Operator-level users can issue this command. Example To disable SNMP authentication trap support: DES-3200-28/ME:admin#disable snmp authenticate_traps Command: disable snmp authenticate_traps Success. DES-3200-28/ME:admin# 63-27 enable snmp linkchange_traps Description This command is used to configure the sending of linkchange traps. Format enable snmp linkchange_traps Parameters None.
PAGE 560
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions Only Administrator and Operator-level users can issue this command. Example To disable the sending of linkchange traps: DES-3200-28/ME:admin#disable snmp linkchange_traps Command: disable snmp linkchange_traps Success.
PAGE 561
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 63-30 config snmp coldstart_traps Description This command is used to configure the trap for coldstart event. Format config snmp coldstart_traps [enable | disable] Parameters enable - Enable the trap of the coldstart event. The default state is enabled. disable - Disable the trap of the coldstart event. Restrictions Only Administrator-level users can issue this command.
PAGE 562
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure the trap state for warmstart event: DES-3200-28/ME:admin#config snmp warmstart_traps enable Command: config snmp warmstart_traps enable Success. DES-3200-28/ME:admin# 63-32 show snmp traps Description This command is used to display the snmp trap sending status.
PAGE 563
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config rmon trap {rising_alarm [enable | disable] | falling_alarm [enable | disable]} (1) Parameters rising_alarm - (Optional) Specify the trap state for rising alarm. The default state is enabled. enable - Specify that the rising alarm function will be enabled. disable - Specify that the rising alarm function will be disabled. falling_alarm - (Optional) Specify the trap state for falling alarm.
PAGE 564
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show rmon Command: show rmon RMON Rising Alarm Trap RMON Falling Alarm Trap : Enabled : Enabled DES-3200-28/ME:admin# 560
PAGE 565
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 64 Single IP Management Command List enable sim disable sim show sim {[candidates {} | members{} | group {commander_mac } | neighbor]} reconfig {member_id | exit} config sim_group [add {} | delete ] config sim [{[commander {group_name } | candidate] | dp_interval | hold_time
PAGE 566
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 64-2 disable sim Description This command is used to disable single IP management on the Switch. Format disable sim Parameters None. Restrictions Only Administrator-level users can issue this command. Example To disable SIM: DES-3200-28/ME:admin#disable sim Command: disable sim Success.
PAGE 567
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions None. Example To show the self information in detail: DES-3200-28/ME:admin#show sim Command: show sim SIM Version Firmware Version Device Name MAC Address Capabilities Platform SIM State Role State Discovery Interval Hold Time : : : : : : : : : : VER-1.61 4.04.
PAGE 568
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show sim member Command: show sim member ID MAC Address Platform / Hold Firmware Device Name Capability Time Version --- ----------------- ------------------------ ----- --------- ---------------1 00-01-02-03-04-00 DES-XXXXS L2 Switch 40 1.00-B01 aaaaaaaaaaaaaaaa bbbbbbbbbbbbbbb 2 00-55-55-00-55-00 DES-3326SR L3 Switch 140 4.
PAGE 569
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show sim neighbor Command: show sim neighbor Neighbor Table Port -----23 23 24 MAC Address -----------------00-35-26-00-11-99 00-35-26-00-11-91 00-35-26-00-11-90 Role --------Commander Member Candidate Total Entries: 3 DES-3200-28/ME:admin# 64-4 reconfig Description This command is used to re-telnet to member.
PAGE 570
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config sim_group [add {} | delete ] Parameters add - Specify to add a specific candidate to the group. - Enter the candidate ID to be added to the group here. This value must be between 1 and 100. - (Optional) The password of candidate if necessary. delete - Specify to delete a member from the group.
PAGE 571
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config sim [{[commander {group_name } | candidate] | dp_interval | hold_time }] Parameters commander - (Optional) Specify to transfer the role to the commander. group_name - (Optional) Specify that if the user is the commander, the user can update the name of group. - Enter the group name here. This name can be up to 64 characters long.
PAGE 572
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config sim dp_interval 30 Command: config sim dp_interval 30 Success. DES-3200-28/ME:admin# To change the hold time of discovery protocol: DES-3200-28/ME:admin#config sim hold_time 200 Command: config sim hold_time 200 Success. DES-3200-28/ME:admin# 64-7 download sim_ms Description This command is used to download firmware or configuration to indicated device.
PAGE 573
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#download sim_ms configuration_from_tftp 10.55.47.1 D:\dwl600x.tfp members 1 Commands: download sim_ms configuration_from_tftp 10.55.47.1 D:\dwl600x.tfp members 1 This device is updating configuration. Please wait several minutes ...
PAGE 574
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions Only Administrator-level users can issue this command. Example To upload configuration: DES-3200-28/ME:admin#upload sim_ms configuration_to_tftp 10.55.47.1 D:\configuration.txt members 1 Command: upload sim_ms configuration_to_tftp 10.55.47.1 D:\configuration.txt members 1 This device is uploading configuration. Please wait several minutes ...
PAGE 575
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 65 Syslog and Trap Sourceinterface Command List config syslog source_ipif [ {} | none] show syslog source_ipif config trap source_ipif [ {} | none] show trap source_ipif 65-1 config syslog source_ipif Description This command is used to configure syslog source IP interface.
PAGE 576
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config syslog source_ipif none Command: config syslog source_ipif none Success DES-3200-28/ME:admin# 65-2 show syslog source_ipif Description This command is used to display the syslog source IP interface. Format show syslog source_ipif Parameters None. Restrictions None.
PAGE 577
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters ipif - Specify the IP interface name. If only specify this parameter, the least IPv4 address and the smallest IPv6 address of ipif_name will be used as source IP addresses. - Enter the IP interface name here. This name can be up to 12 characters long. - (Optional) Enter the IP address used for the configuration here. none - Specify to clear the configured source IP interface.
PAGE 578
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example Show trap source IP interface: DES-3200-28/ME P:admin#show trap source_ipif Command: show trap source_ipif Trap Source IP Interface Configuration: IP Interface IPv4 Address : System : None DES-3200-28/ME:admin# 574
PAGE 579
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 66 System Log Command List clear log show log {[index | severity {module } {emergency | alert | critical | error | warning | notice | informational | debug | } | module]} show log_software_module enable syslog disable syslog show syslog create syslog host ipaddress {severity [emergency | alert | critical | error | warning | notice | informati
PAGE 580
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 66-2 show log Description This command is used to display the Switch’s history log. Format show log {[index | severity {module } {emergency | alert | critical | error | warning | notice | informational | debug | } | module]} Parameters index - (Optional) The show log command will display the history log between the log number of X and Y.
PAGE 581
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show log index 1-3 Command: show log index 1-3 Index Date Time Level Log Text ----- ---------- -------- ------- ---------------------------------------------3 2 1 2000-01-01 00:00:40 CRIT(2) System started up 2000-01-01 00:00:40 CRIT(2) System cold start 2000-01-01 01:49:30 INFO(6) Anonymous: execute command "reset system".
PAGE 582
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions Only Administrator and Operator-level users can issue this command. Example To enable the sending of syslog messages: DES-3200-28/ME:admin#enable syslog Command: enable syslog Success. DES-3200-28/ME:admin# 66-5 disable syslog Description This command is used to disable the sending of syslog messages. Format disable syslog Parameters None.
PAGE 583
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 66-6 show syslog Description This command is used to display the syslog protocol global state. Format show syslog Parameters None. Restrictions None. Example To display the syslog protocol global state: DES-3200-28/ME:admin#show syslog Command: show syslog Syslog Global State: Enabled DES-3200-28/ME:admin# 66-7 create syslog host Description This command is used to create a new syslog host.
PAGE 584
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide error - Severity level 3 warning - Severity level 4 notice - Severity level 5 informational - Severity level 6 debug - Severity level 7 - Enter the severity level value here. This value must be between 0 and 7. facility - (Optional) Some of the operating system daemons and processes have been assigned Facility values.
PAGE 585
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide local5 | local6 | local7] | udp_port | ipaddress | state [enable | disable]} Parameters - Enter the host index value here. all - Specify that all the host indexes will be used. severity - (Optional) Specify the severity level.
PAGE 586
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 66-9 delete syslog host Description This command is used to delete the syslog host(s). Format delete syslog host [ | all] Parameters host - The host index or all hosts. - Enter the host index value here. all - Specify that all the host indexes will be used. Restrictions Only Administrator and Operator-level users can issue this command.
PAGE 587
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To show the syslog host information: DES-3200-28/ME:admin#show syslog host Command: show syslog host Syslog Global State: Disabled Host 1 IP Address Severity Facility UDP Port Status : : : : : 10.90.90.1 Debug(7) Local0 514 Disabled Total Entries : 1 DES-3200-28/ME:admin# 66-11 config log_save_timing Description This command is used to set the method for saving the log.
PAGE 588
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 66-12 show log_save_timing Description This command is used to show the method for saving the log. Format show log_save_timing Parameters None. Restrictions None.
PAGE 589
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions None.
PAGE 590
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 67 System Severity Command List config system_severity [trap | log | all] [emergency | alert| critical | error | warning | notice | information | debug | ] show system_severity 67-1 config system_severity Description This command is used to configure the severity level control for the system.
PAGE 591
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide 67-2 show system_severity Description This command is used to display the severity level controls for the system. Format show system_severity Parameters None. Restrictions None.
PAGE 592
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 68 Telnet Client Command List telnet {tcp_port } 68-1 telnet Description This command is used to start the telnet client to connect to the specific telnet server. The parameters specified by the command will only be used for the establishment of this specific session. They will not affect the establishment of other sessions.
PAGE 593
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 69 TFTP/FTP Client Command List download [firmware_fromTFTP { src_file {dest_file } {boot_up}} | cfg_fromTFTP { src_file {dest_file }} | firmware_fromFTP [ {tcp_port } src_file | ftp:] {dest_file {boot_up}} | cfg_fromFT
PAGE 594
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters firmware_fromTFTP – Specify to download firmware from a TFTP server. - (Optional) The IP address of the TFTP server. src_file - (Optional) Used to identify the parameter “path_filename”. - Enter the source file path name here. This name can be up to 64 characters long. dest_file - (Optional) Used to identify the parameter “path_filename”.
PAGE 595
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#download firmware_fromTFTP 10.54.71.1 src_file px.had Command: download firmware_fromTFTP 10.54.71.1 src_file px.had Connecting to server................... Done. Download firmware...................... Done. Please wait, programming flash......... Done. Do not power off! DES-3200-28/ME:admin# To download configuration from TFTP: DES-3200-28/ME:admin#download cfg_fromTFTP 10.54.71.1 src_file cfg01.
PAGE 596
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide long. src_file - (Optional) Used to identify the parameter “path_filename”. - The pathname specifies an absolute pathname on the device file system. include - (Optional) Specify to include lines that contain the specified filter string. exclude - (Optional) Specify to exclude lines that contain the specified filter string.
PAGE 597
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide src_file - (Optional) Used to identify the parameter “path_filename”. - The pathname specifies an absolute pathname on the device file system. If pathname is not specified, it refers to the boot_up image. This name can be up to 64 characters long. cfg_toFTP – Specify that the configuration file will be uploaded to the FTP server. - The IP address of the FTP server. tcp_port - Specify the TCP port.
PAGE 598
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide dest_file - Used to identify the parameter “path_filename”. - The pathname specifies the pathname on the FTP server. It can be a relative pathname or an absolute pathname. This name can be up to 64 characters long. ftp: - Specify the FTP site. - Enter the FTP directory. attack_log_toFTP – Specify that the attack log will be uploaded to the FTP server.
PAGE 599
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#upload firmware_toTFTP 10.90.90.10 dest_file D:/firmware.had src_file 4.00.020.had Command: upload firmware_toTFTP 10.90.90.10 dest_file D:/firmware.had src_file 4.00.020.had No such file or directory. Fail! DES-3200-28/ME:admin# To upload configuration from TFTP: DES-3200-28/ME:admin#upload cfg_toTFTP 10.90.90.10 dest_file d:\config.cfg Command: upload cfg_toTFTP 10.90.90.10 dest_file d:\config.
PAGE 600
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config tftp {server | firmware_file | cfg_file | log_file | attack_log_file | certificate_file | key_file | tech_support_file | debug_error_log_file | sim_firmware_file | sim_cfg_file | sim_log_file } Para
PAGE 601
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config tftp server 10.90.90.10 Command: config tftp server 10.90.90.10 Success. DES-3200-28/ME:admin# To configure TFTP server and specify the pre defined firmware file, log file: DES-3200-28/ME:admin#config tftp server 10.90.90.1 firmware_file DES3200.had cfg_file log_tmp Command: config tftp server 10.90.90.1 firmware_file DES3200.had cfg_file log_tmp Success.
PAGE 602
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show tftp Command: show tftp TFTP Server Settings IPv4 Address : 10.90.90.1 File Type -------------------firmware_file cfg_file log_file attack_log_file certificate_file key_file tech_support_file debug_error_log_file sim_firmware_file sim_cfg_file sim_log_file Path_filename ---------------------DES3200.
PAGE 603
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 70 Time and SNTP Command List config sntp {primary | secondary | poll-interval } show sntp enable sntp disable sntp config time config time_zone {operator [+ | -] | hour | min } config dst [disable | repeating {s_week | s_day | s_mth | s_time | e_w
PAGE 604
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config sntp primary 10.1.1.1 secondary 10.1.1.2 pollinterval 30 Command: config sntp primary 10.1.1.1 secondary 10.1.1.2 poll-interval 30 Success. DES-3200-28/ME:admin# 70-2 show sntp Description This command is used to display SNTP current time source and configuration. Format show sntp Parameters None. Restrictions None.
PAGE 605
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions Only Administrator and Operator-level users can issue this command. Example To enable SNTP: DES-3200-28/ME:admin#enable sntp Command: enable sntp Success. DES-3200-28/ME:admin# 70-4 disable sntp Description This command is used to turn off SNTP support. Format disable sntp Parameters None. Restrictions Only Administrator and Operator-level users can issue this command.
PAGE 606
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Format config time Parameters - Specify the system clock date. An example would look like this: '30jun2010'. - Specify the system clock time. An example would look like this: '12:00:00'. Restrictions Only Administrator and Operator-level users can issue this command.
PAGE 607
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To configure time_zone: DES-3200-28/ME:admin#config time_zone operator + hour 2 min 30 Command: config time_zone operator + hour 2 min 30 Success. DES-3200-28/ME:admin# 70-7 config dst Description This command is used to configure Daylight Saving Time of the device.
PAGE 608
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide annual - Set the Daylight Saving Time to annual mode. s_date, e_date - (Optional) Configure the start /end date of Daylight Saving Time. - Enter the starting date of Daylight Saving Time here. This range must be between 1 an 31. - Enter the ending date of Daylight Saving Time here. This range must be between 1 an 31.
PAGE 609
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Restrictions None.
PAGE 610
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 71 Trace Route Command List traceroute {ttl } {port } {timeout } {probe } traceroute6 {ttl | port | timeout | probe } 71-1 traceroute Description This command is used to trace the routed path between the Switch and a destination end station.
PAGE 611
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#traceroute 10.48.74.121 probe 3 Command: traceroute 10.48.74.121 probe 3 1 2 3 <10 ms. <10 ms. <10 ms. 10.12.73.254 10.19.68.1 10.48.74.121 Trace complete. DES-3200-28/ME:admin# 71-2 traceroute6 Description This command is used to trace the IPv6 routed path between the Switch and a destination end station.
PAGE 612
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#traceroute6 3000::1 probe 3 Command: traceroute6 3000::1 probe 3 1 2 3 <10 ms. <10 ms. <10 ms. 1345:142::11 2011:14::100 3000::1 Trace complete. DES-3200-28/ME:admin# Trace the IPv6 routed path between the Switch and 1210:100::11 with port 40000: DES-3200-28/ME:admin#traceroute6 1210:100::11 port 40000 Command: traceroute6 1210:100::11 port 40000 1 2 3 <10 ms. <10 ms. <10 ms.
PAGE 613
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 72 Traffic Control Command List config traffic control [ | all] {broadcast [enable | disable] | multicast [enable | disable] |unicast [enable | disable] | action [drop | shutdown] | threshold | countdown [ | | disable] | time_interval } config traffic trap [none | storm_occurred | storm_cleared | both] show traffic control {} config traffic control log
PAGE 614
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide countdown - (Optional) Timer for shutdown mode. If a port enters the shutdown Rx state and this timer runs out, port will be shutdown forever. The parameter is not applicable if “drop” (mode) is specified for the “action” parameter. - 0 disables the forever state, meaning that the port will not enter the shutdown forever state. - Enter the countdown timer value here. This value must be between 3 and 30.
PAGE 615
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Example To enable both the occurred mode and cleared mode traffic control traps: DES-3200-28/ME:admin#config traffic trap both Command: config traffic trap both Success. DES-3200-28/ME:admin# 72-3 show traffic control Description This command is used to display the current traffic control settings. Format show traffic control {} Parameters - (Optional) Used to specify the range of ports to be shown.
PAGE 616
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show traffic control Command: show traffic control 1-10 1-10 Traffic Control Trap : [Both] Traffic Control Log : Enabled Traffic Control Auto Recover Time: 0 Minutes Port Thres hold ---- -----1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 1 10 1 Broadcast Storm --------Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Multicast Storm --------Disabled Disabled Disabled Disabled Disabled
PAGE 617
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config traffic control log state enable Command: config traffic control log state enable Success. DES-3200-28/ME:admin# 72-5 config traffic control auto_recover_time Description This command is used to configure the traffic auto recover time that allowed for a port to recover from shutdown forever status.
PAGE 618
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 73 Traffic Segmentation Command List config traffic_segmentation [ | all] forward_list [null | all | ] show traffic_segmentation {} 73-1 config traffic_segmentation Description This command is used to configure the traffic segmentation.
PAGE 619
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters - (Optional) Specify a range of ports to be displayed. If no parameter is specified, the system will display all current traffic segmentation tables. Restrictions None.
PAGE 620
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 74 Trusted Host Command List create trusted_host [ | network ] {snmp | telnet | ssh | http | https | ping} delete trusted_host [ipaddr | network | all] config trusted_host [ | network ] [add | delete] {snmp | telnet | ssh | http | https | ping | all} show trusted_host 74-1 create trusted_host Description This command is used to create the
PAGE 621
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#create trusted_host 10.48.74.121 Command: create trusted_host 10.48.74.121 Success. DES-3200-28/ME:admin# 74-2 delete trusted_host Description This command is used to delete a trusted host entry made using the create trusted_host command above. Format delete trusted_host [ipaddr | network | all] Parameters ipaddr - The IP address of the trusted host.
PAGE 622
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters - The IP address of the trusted host. network - The network address of the trusted network. The form of network address is xxx.xxx.xxx.xxx/y. - Enter the network address used here. add - Add interfaces for that trusted host. delete - Delete interfaces for that trusted host. snmp - (Optional) Specify trusted host for SNMP. telnet - (Optional) Specify trusted host for TELENT.
PAGE 623
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show trusted_host Command: show trusted_host Management Stations IP Address Access Interface ---------------------------------------------------------------10.48.74.
PAGE 624
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 75 Unicast Routing Command List create iproute [default] {} delete iproute [default] show iproute {} {static} 75-1 create iproute Description This command is used to create an IP static route. Format create iproute [default] {} Parameters default - Create an IP default route (0.0.0.0/0). - The IP address for the next hop router.
PAGE 625
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters default - Deletes an IP default route (0.0.0.0/0). Restrictions Only Administrator, Operator and Power-User level users can issue this command. Example To delete an IP default route: DES-3200-28/ME:admin#delete iproute default 10.1.1.254 Command: delete iproute default 10.1.1.254 Success. DES-3200-28/ME:admin# 75-3 show iproute Description This command is used to display the Switch’s current IP routing table.
PAGE 626
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show iproute Command: show iproute Routing Table IP Address/Netmask -----------------10.1.1.0/24 192.168.1.0/24 Gateway --------------0.0.0.0 0.0.0.
PAGE 627
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 76 VLAN Trunking Command List enable vlan_trunk disable vlan_trunk config vlan_trunk ports [ | all] | state [enable | disable] show vlan_trunk 76-1 enable vlan_trunk Description This command is used to enable the VLAN trunk function. When the VLAN trunk function is enabled, the VLAN trunk ports shall be able to forward all tagged frames with any VID. Format enable vlan_trunk Parameters None.
PAGE 628
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions Only Administrator-level users can issue this command. Example To disable the VLAN Trunk: DES-3200-28/ME:admin#disable vlan_trunk Command: disable vlan_trunk Success. DES-3200-28/ME:admin# 76-3 config vlan_trunk Description This command is used to configure a port as a VLAN trunk port. By default, none of the port is a VLAN trunk port.
PAGE 629
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters - Enter a list of ports used for the configuration here. all - Specify that all the ports will be used for this configuration. state - Specify that the port is a VLAN trunk port or not. enable - Specify that the port is a VLAN trunk port. disable - Specify that the port is not a VLAN trunk port. Restrictions Only Administrator-level users can issue this command.
PAGE 630
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#config vlan_trunk ports 7 state disable Command: config vlan_trunk ports 7 state disable Success. DES-3200-28/ME:admin# Port 6, 7 have the same VLAN configuration before enabling VLAN trunk. Port 6 is LA-1 member port; port 7 is LA-1 master port. DES-3200-28/ME:admin#config vlan_trunk ports 7 state disable Command: config vlan_trunk ports 7 state disable Success.
PAGE 631
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DES-3200-28/ME:admin#show vlan_trunk Command: show vlan_trunk VLAN Trunk Global Setting ---------------------------VLAN Trunk Status : Disabled VLAN Trunk Member Ports : 1-5 DES-3200-28/ME:admin# The following example displays the VLAN information which will also display VLAN trunk setting: DES-3200-28/ME:admin#show vlan Command: show vlan VLAN Trunk State : Enabled VLAN Trunk Member Ports : 1-5 VID : 1 VLAN Type : Static
PAGE 632
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Chapter 77 Password Recovery Command List enable password_recovery disable password_recovery show password_recovery 77-1 enable password_recovery Description This command is used to enable the password recovery mode. Format enable password_recovery Parameters None. Restrictions Only Administrator-level users can issue this command.
PAGE 633
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Parameters None. Restrictions Only Administrator-level users can issue this command. Example To disable the password recovery mode: DES-3200-28/ME:admin#disable password_recovery Command: disable password_recovery Success. DES-3200-28/ME:admin# 77-3 show password_recovery Description This command is used to display the password recovery state. Format show password_recovery Parameters None.
PAGE 634
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Appendix A Procedure Password Recovery This chapter describes the procedure for resetting passwords on D-Link switches. Authenticating any user who tries to access networks is necessary and important. The basic authentication method used to accept qualified users is through a local login, utilizing a Username and Password.
PAGE 635
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Command Parameters reset account The reset account command deletes all the previously created accounts. reset password {} The reset password command resets the password of the specified user. If a username is not specified, the passwords of all users will be reset. show account The show account command displays all previously created accounts.
PAGE 636
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Appendix B System Log Entries The following table lists all possible entries and their corresponding meanings that will appear in the System Log of this Switch.
PAGE 637
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide ) Interface Console Web Telnet Log message successfully uploaded Log message successfully uploaded by console Informational (Username: , IP: ) Log message upload was unsuccessful Log message upload by console was unsuccessful! (Username: , IP: ) Warning Firmware successfully uploaded Firmware successfully uploaded by console (Username: , IP: ) Inform
PAGE 638
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide DoS SSH Disable spanning tree protocol Spanning Tree Protocol is disabled Informational New root bridge CIST New Root bridge selected ( MAC: Priority :) Informational New root bridge CIST Region New Root bridge selected ( MAC: Priority :) Informational New root bridge MSTI Region New Root bridge selected (Instance:, MAC: Priority :) Informational New
PAGE 639
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide AAA SSH server is disabled SSH server is disabled Informational Authentication Policy is enabled Authentication Policy is enabled (Module: AAA) Informational Authentication Policy is disabled Authentication Policy is disabled (Module: AAA) Informational Successful login through Console authenticated by AAA local method Successful login through Console authenticated Informational by AAA local method (Username:
PAGE 640
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide AAA server ) Login failed through Console authenticated by Login failed through Console AAA server (Username: authenticated by AAA server ) Warning Login failed through Console Login failed through Console due to AAA server due to AAA server timeout or timeout or improper configuration (Username: Warning improper configuration ) Successful login through Web authenticated by AAA serv
PAGE 641
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide by AAA local_enable method method (Username: ) Enable Admin failed through Enable Admin failed through Web from Web authenticated by AAA authenticated by AAA local_enable method Warning local_enable method (Username: ) Successful Enable Admin through Web(SSL) authenticated by AAA local_enable method Successful Enable Admin through Web(SSL) from authenticated by AAA Informational local_en
PAGE 642
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Enable Admin failed through Enable Admin failed through Web from Web authenticated by AAA authenticated by AAA server Warning server (Username: ) Enable Admin failed through Enable Admin failed through Web from Web due to AAA server due to AAA server timeout or improper Warning timeout or improper configuration (Username: ) configuration Successful Enable Admin Successful Enabl
PAGE 643
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide conflict with static FDB Dynamic IMPB entry conflicts with static Dynamic IMPB entry conflicts IMPB(IP: , MAC: , Port with static IMPB ) Warning Creating IMPB entry failed due to no ACL rule Creating IMPB entry failed being available(IP:, MAC: , due to no ACL rule available Port ) Warning Management IP address was changed by (Username: ,IP:) Informatio
PAGE 644
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide after radius client authenticated by radius server successfully.This 802.1p default priority will assign to the port. (account : ) 802.1x Authentication failure from (Username: 802.1x Authentication failure , Port: , MAC: ) CFM Warning 802.1x Authentication success 802.
PAGE 645
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide maximum user limit The authorized user number on whole device is below the MAC-based Access Control recovers from stop maximum user limit in a time learning state interval (interval is project depended) Warning BPDU Protection BPDU attack happened Port enter BPDU under protection state (mode: drop ) Informational BPDU attack happened Port enter BPDU under protection state (mode: block) Informational BPDU
PAGE 646
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Appendix C Trap Log Entries This table lists the trap logs found on the Switch.
PAGE 647
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide swFanRecover swFanUnitIndex V2 Equipment.MIB V2 Equipment.MIB V2 Equipment.MIB V2 Equipment.MIB V2 Equipment.
PAGE 648
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide swVlanLoopDetectVID swDdmAlarmTrap swDdmPort V2 DDM.MIB V2 DDM.MIB V2 BPDUProtection .MIB V2 BPDUProtection .
PAGE 649
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide swExternalAlarmMessage swDoSAttackDetected 1: swDoSCtrlType 2: swDoSNotifyVarIpAddr 3: swDoSNotifyVarPortNumber 645 V1/V2 DOSPrev.
PAGE 650
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide Appendix D RADIUS Attributes Assignment The RADIUS Attributes Assignment on the DES-3200 is used in the following modules: 802.1X (Port-based and Host-based), and MAC-based Access Control. The description that follows explains the following RADIUS Attributes Assignment types:     Ingress/Egress Bandwidth 802.
PAGE 651
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide priority of the port. If the user has configured the 802.1p priority attribute of the RADIUS server (for example, priority 7) and the 802.1X, or MAC-based authentication is successful, the device will assign the 802.1p default priority (according to the RADIUS server) to the port. However, if the user does not configure the priority attribute and authenticates successfully, the device will not assign a priority to this port.
PAGE 652
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide access_profile profile_id 1 add access_id auto_assign ethernet vlan_id 1 port all deny; If the user has configured the ACL attribute of the RADIUS server (for example, ACL profile: create access_profile profile_id 1 profile_name profile1 ethernet vlan 0xFFF; ACL rule: config access_profile profile_id 1 add access_id auto_assign ethernet vlan_id 1 port all deny), and the MAC-based Access Cotntrol authentication is successful, t