User manual
Table Of Contents
- Table of Contents
- About This Guide
- 1 Product Introduction
- 2 Hardware Installation
- 3 Getting Started
- 4 Configuration
- Web-based Management
- Tool Bar > Save Menu
- Tool Bar > Tool Menu
- Tool Bar > Online Help
- Function Tree
- Device Information
- System > System Settings
- System > Serial Port Settings
- System > IPv6 System Settings
- System > IPv6 Route Settings
- System > IPv6 Neighbor Settings
- System > DHCP Auto Configuration
- System > Trap Settings
- System > Port Configuration > Port Settings
- System > Port Configuration > Port Description
- System > Port Configuration > Port Error Disabled
- System > SNMP Settings > SNMP Global State
- System > SNMP Settings > SNMP User Table
- System > SNMP Settings > SNMP Group Table
- System > SNMP Settings > SNMP View Table
- System > SNMP Settings > SNMP Community Table
- System > SNMP Settings > SNMP Host Table
- System > SNMP Settings > SNMP Engine ID
- System > SNMP Settings > SNMP Trap Settings
- System > User Accounts
- System > MAC Address Aging Time
- System > ARP Aging Time Settings
- System > PPPoE Circuit ID Insertion Settings
- System > Web Settings
- System > Telnet Settings
- System > Password Encryption
- System > Ping Test
- System > MAC Notification Settings
- System > System Log Configuration > System Log Settings
- System > System Log Configuration > System Log Server
- System > SMTP Service > SMTP Server Settings
- System > SMTP Service > SMTP Service
- Configuration > 802.1Q VLAN
- Configuration > 802.1Q Management VLAN
- Configuration > VLAN Status
- Configuration > GVRP Settings
- Configuration > GVRP Timer Settings
- Configuration > QinQ > QinQ Settings
- Configuration > QinQ > VLAN Translation CVID Entry Settings
- Configuration > 802.1v Protocol VLAN > 802.1v Protocol Group Settings
- Configuration > 802.1v Protocol VLAN > 802.1v Protocol VLAN Settings
- Configuration > VLAN Trunk Settings
- Configuration > Link Aggregation > Port Trunkings
- Configuration > Link Aggregation > LACP Port Settings
- Configuration > BPDU Protection Settings
- Configuration > IGMP Snooping > IGMP Snooping
- Configuration > IGMP Snooping > IGMP Access Control Settings
- Configuration > IGMP Snooping > ISM VLAN Settings
- Configuration > IGMP Snooping > Host Table
- Configuration > IGMP Snooping > IP Multicast Profile Settings
- Configuration > IGMP Snooping > Limited Multicast Range Settings
- Configuration > IGMP Snooping > Max Multicast Group Settings
- Configuration > MLD Snooping > MLD Snooping Settings
- Configuration > MLD Snooping > MLD Host Table
- Configuration > Port Mirroring
- Configuration > Loopback Detection
- Configuration > SNTP Settings > Time Settings
- Configuration > SNTP Settings > TimeZone Settings
- Configuration > DHCP/BOOTP Relay > DHCP/BOOTP Relay Global Settings
- Configuration > DHCP/BOOTP Relay > DHCP/BOOTP Relay Interface Settings
- Configuration > DHCP Local Relay Settings
- Configuration > DHCPv6 Relay Settings
- Configuration > Firmware Information
- Configuration > Spanning Tree > STP Bridge Global Settings
- Configuration > Spanning Tree > STP Port Settings
- Configuration > Spanning Tree > MST Configuration Identification
- Configuration > Spanning Tree > STP Instance Settings
- Configuration > Spanning Tree > MSTP Port Information
- Configuration > Ethernet OAM > Ethernet OAM Port Settings
- Configuration > Ethernet OAM > Ethernet OAM Event Configuration
- Configuration > DULD > DULD Port Settings
- Configuration > Multicast Forwarding & Filtering > Multicast Forwarding
- Configuration > Multicast Forwarding & Filtering > Multicast Filtering
- QoS > Traffic Control
- QoS > Bandwidth Control
- QoS > CoS Scheduling Mechanism
- QoS > CoS Output Scheduling
- QoS > 802.1p Default Priority
- QoS > 802.1p User Priority
- QoS > DSCP Priority Settings
- QoS > Priority Settings
- QoS > MAC Priority Settings
- QoS > IP Priority Settings
- QoS > IPv6 Priority Settings
- QoS > IPv6 Traffic Class Priority Settings
- QoS > TCP/UDP Port Priority Settings
- QoS > VLAN ID Priority Settings
- QoS > Protocol Priority Settings
- RMON > RMON Basic Settings
- RMON > RMON Ethernet Statistics Configuration
- RMON > RMON History Control Configuration
- RMON > RMON Alarm Configuration
- RMON > RMON Event Configuration
- Security > Trusted Host
- Security > Safeguard Engine
- Security > ARP Spoofing Prevention
- Security > Gratuitous ARP
- Security > Port Security
- Security > SSL Settings
- Security > Smart Binding > Smart Binding Settings
- Security > Smart Binding > Smart Binding
- Security > Smart Binding > White List
- Security > Smart Binding > Black List
- Security > Smart Binding > DHCP Snooping List
- Security > 802.1X > 802.1X Settings
- Security > 802.1X > 802.1X User
- Security > 802.1X > 802.1X Authentication RADIUS
- Security > 802.1X > 802.1X Guest VLAN
- Security > MAC Address Table > Static MAC
- Security > MAC Address Table > Dynamic Forwarding Table
- Security > Access Authentication Control > Authentication Policy Settings
- Security > Access Authentication Control > Application Authentication Settings
- Security > Access Authentication Control > Authentication Server Group
- Security > Access Authentication Control > Authentication Server
- Security > Access Authentication Control > Login Method Lists
- Security > Access Authentication Control > Enable Method Lists
- Security > Access Authentication Control > Local Enable Password Settings
- Security > Traffic Segmentation
- Security > DoS Prevention Settings
- Security > DHCP Server Screening > DHCP Server Screening Port Settings
- Security > DHCP Server Screening > Filter DHCP Server
- Security > SSH Settings > SSH Settings
- Security > SSH Settings > SSH Authmode and Algorithm Settings
- Security > SSH Settings > SSH User Authentication Lists
- Monitoring > Statistics
- Monitoring > Session Table
- Monitoring > CPU Utilization
- Monitoring > Memory Utilization
- Monitoring > Port Utilization
- Monitoring > Packet Size
- Monitoring > Packets > Transmitted (TX)
- Monitoring > Packets > Received (RX)
- Monitoring > Packets > UMB Cast (RX)
- Monitoring > Errors > Received (RX)
- Monitoring > Errors > Transmitted (TX)
- Monitoring > Cable Diagnostics
- Monitoring > System Log
- Monitoring > Browse ARP Table
- Monitoring > Ethernet OAM > Browse Ethernet OAM Event Log
- Monitoring > Ethernet OAM > Browse Ethernet OAM Statistics
- Monitoring > Port Access Control > RADIUS Authentication
- Monitoring > Port Access Control > RADIUS Account Client
- ACL > ACL Configuration Wizard
- ACL > Access Profile List
- ACL > ACL Finder
- ACL > CPU Filter Configuration Wizard
- ACL > CPU Filter Access Profile List
- ACL > CPU Filter Finder
- LLDP > LLDP Global Settings
- LLDP > Basic LLDP Port Settings
- LLDP > 802.1 Extension LLDP Port Settings
- LLDP > 802.3 Extension LLDP Port Settings
- LLDP > LLDP Management Address Settings
- LLDP > LLDP Statistics Table
- LLDP > LLDP Management Address Table
- LLDP > LLDP Local Port Table
- LLDP > LLDP Remote Port Table
- Appendix A - Ethernet Technology
- Appendix B - Ethernet Technology
- Appendix C – Rack mount Instructions
- Appendix D – Cables and Connectors
- Appendix E– Module Specs and Cable Lengths
4 Configuration DES-1210 Metro Ethernet Managed Switch User Manual
59
based Traffic Control implementations. The possible time settings for this field are 0, 5-30 minutes. 0 denotes
that the port will never shutdown.
Time Interval (5-30): The interval will set the time between Multicast and Broadcast packet counts sent from
the Switch’s chip to the Traffic Control function. These packet counts are the determining factor in deciding
when incoming packets exceed the Threshold value. The interval may be set between 5 and 30 seconds with
the default setting of 5 seconds.
Shutdown Threshold (0-255000): Specify the shutdown threshold for traffic threshold.
Storm Control Type: User can select the different Storm type from Broadcast, Multicast, Broadcast +
Multicast, Unknown Unicast, Broadcast + Unknown Unicast, Multicast + Unknown Unicast, and Broadcast +
Multicast + Unknown Unicast.
Click Apply for the settings to take effect.
NOTE: Traffic Control cannot be implemented on
ports that are set for Link Aggregation.
NOTE: Ports that are in the rest mode will be
seen as Discarding in Spanning Tree windows
and implementations though these ports will still
be forwarding BPDUs to the Switch’s CPU.
NOTE: Ports that are in rest mode will be seen as
link down in all windows and screens until it
enters the auto-recovery mode or the user
recovers these ports by configuring the port state.
QoS > Bandwidth Control
The Bandwidth Control page allows network managers to define the bandwidth settings for a specified port’s
transmitting and receiving data rates.
Figure 4.93 – QoS > Bandwidth Control
From Port / To Port: A consecutive group of ports may be configured starting with the selected port.
Type: This drop-down menu allows you to select between RX (receive), TX (transmit), and Both. This
setting will determine whether the bandwidth ceiling is applied to receiving, transmitting, or both
receiving and transmitting packets.
No Limit: This drop-down menu allows you to specify that the selected port will have no bandwidth limit.
Enabled disables the limit.
Rate (63-1024000): This field allows you to enter the data rate, in Kbits per second, will be the limit for the
selected port. The value is between 63 and 1024000.
Click Apply to set the bandwidth control for the selected ports.
NOTE: The TX rate for Gigabit ports can only be
configured in multiples of 1850kbps. If any other