User manual
Table Of Contents
- Table of Contents
- About This Guide
- 1 Product Introduction
- 2 Hardware Installation
- 3 Getting Started
- 4 Configuration
- Web-based Management
- Tool Bar > Save Menu
- Tool Bar > Tool Menu
- Tool Bar > Online Help
- Function Tree
- Device Information
- System > System Settings
- System > Serial Port Settings
- System > IPv6 System Settings
- System > IPv6 Route Settings
- System > IPv6 Neighbor Settings
- System > DHCP Auto Configuration
- System > Trap Settings
- System > Port Configuration > Port Settings
- System > Port Configuration > Port Description
- System > Port Configuration > Port Error Disabled
- System > SNMP Settings > SNMP Global State
- System > SNMP Settings > SNMP User Table
- System > SNMP Settings > SNMP Group Table
- System > SNMP Settings > SNMP View Table
- System > SNMP Settings > SNMP Community Table
- System > SNMP Settings > SNMP Host Table
- System > SNMP Settings > SNMP Engine ID
- System > SNMP Settings > SNMP Trap Settings
- System > User Accounts
- System > MAC Address Aging Time
- System > ARP Aging Time Settings
- System > PPPoE Circuit ID Insertion Settings
- System > Web Settings
- System > Telnet Settings
- System > Password Encryption
- System > Ping Test
- System > MAC Notification Settings
- System > System Log Configuration > System Log Settings
- System > System Log Configuration > System Log Server
- System > SMTP Service > SMTP Server Settings
- System > SMTP Service > SMTP Service
- Configuration > 802.1Q VLAN
- Configuration > 802.1Q Management VLAN
- Configuration > VLAN Status
- Configuration > GVRP Settings
- Configuration > GVRP Timer Settings
- Configuration > QinQ > QinQ Settings
- Configuration > QinQ > VLAN Translation CVID Entry Settings
- Configuration > 802.1v Protocol VLAN > 802.1v Protocol Group Settings
- Configuration > 802.1v Protocol VLAN > 802.1v Protocol VLAN Settings
- Configuration > VLAN Trunk Settings
- Configuration > Link Aggregation > Port Trunkings
- Configuration > Link Aggregation > LACP Port Settings
- Configuration > BPDU Protection Settings
- Configuration > IGMP Snooping > IGMP Snooping
- Configuration > IGMP Snooping > IGMP Access Control Settings
- Configuration > IGMP Snooping > ISM VLAN Settings
- Configuration > IGMP Snooping > Host Table
- Configuration > IGMP Snooping > IP Multicast Profile Settings
- Configuration > IGMP Snooping > Limited Multicast Range Settings
- Configuration > IGMP Snooping > Max Multicast Group Settings
- Configuration > MLD Snooping > MLD Snooping Settings
- Configuration > MLD Snooping > MLD Host Table
- Configuration > Port Mirroring
- Configuration > Loopback Detection
- Configuration > SNTP Settings > Time Settings
- Configuration > SNTP Settings > TimeZone Settings
- Configuration > DHCP/BOOTP Relay > DHCP/BOOTP Relay Global Settings
- Configuration > DHCP/BOOTP Relay > DHCP/BOOTP Relay Interface Settings
- Configuration > DHCP Local Relay Settings
- Configuration > DHCPv6 Relay Settings
- Configuration > Firmware Information
- Configuration > Spanning Tree > STP Bridge Global Settings
- Configuration > Spanning Tree > STP Port Settings
- Configuration > Spanning Tree > MST Configuration Identification
- Configuration > Spanning Tree > STP Instance Settings
- Configuration > Spanning Tree > MSTP Port Information
- Configuration > Ethernet OAM > Ethernet OAM Port Settings
- Configuration > Ethernet OAM > Ethernet OAM Event Configuration
- Configuration > DULD > DULD Port Settings
- Configuration > Multicast Forwarding & Filtering > Multicast Forwarding
- Configuration > Multicast Forwarding & Filtering > Multicast Filtering
- QoS > Traffic Control
- QoS > Bandwidth Control
- QoS > CoS Scheduling Mechanism
- QoS > CoS Output Scheduling
- QoS > 802.1p Default Priority
- QoS > 802.1p User Priority
- QoS > DSCP Priority Settings
- QoS > Priority Settings
- QoS > MAC Priority Settings
- QoS > IP Priority Settings
- QoS > IPv6 Priority Settings
- QoS > IPv6 Traffic Class Priority Settings
- QoS > TCP/UDP Port Priority Settings
- QoS > VLAN ID Priority Settings
- QoS > Protocol Priority Settings
- RMON > RMON Basic Settings
- RMON > RMON Ethernet Statistics Configuration
- RMON > RMON History Control Configuration
- RMON > RMON Alarm Configuration
- RMON > RMON Event Configuration
- Security > Trusted Host
- Security > Safeguard Engine
- Security > ARP Spoofing Prevention
- Security > Gratuitous ARP
- Security > Port Security
- Security > SSL Settings
- Security > Smart Binding > Smart Binding Settings
- Security > Smart Binding > Smart Binding
- Security > Smart Binding > White List
- Security > Smart Binding > Black List
- Security > Smart Binding > DHCP Snooping List
- Security > 802.1X > 802.1X Settings
- Security > 802.1X > 802.1X User
- Security > 802.1X > 802.1X Authentication RADIUS
- Security > 802.1X > 802.1X Guest VLAN
- Security > MAC Address Table > Static MAC
- Security > MAC Address Table > Dynamic Forwarding Table
- Security > Access Authentication Control > Authentication Policy Settings
- Security > Access Authentication Control > Application Authentication Settings
- Security > Access Authentication Control > Authentication Server Group
- Security > Access Authentication Control > Authentication Server
- Security > Access Authentication Control > Login Method Lists
- Security > Access Authentication Control > Enable Method Lists
- Security > Access Authentication Control > Local Enable Password Settings
- Security > Traffic Segmentation
- Security > DoS Prevention Settings
- Security > DHCP Server Screening > DHCP Server Screening Port Settings
- Security > DHCP Server Screening > Filter DHCP Server
- Security > SSH Settings > SSH Settings
- Security > SSH Settings > SSH Authmode and Algorithm Settings
- Security > SSH Settings > SSH User Authentication Lists
- Monitoring > Statistics
- Monitoring > Session Table
- Monitoring > CPU Utilization
- Monitoring > Memory Utilization
- Monitoring > Port Utilization
- Monitoring > Packet Size
- Monitoring > Packets > Transmitted (TX)
- Monitoring > Packets > Received (RX)
- Monitoring > Packets > UMB Cast (RX)
- Monitoring > Errors > Received (RX)
- Monitoring > Errors > Transmitted (TX)
- Monitoring > Cable Diagnostics
- Monitoring > System Log
- Monitoring > Browse ARP Table
- Monitoring > Ethernet OAM > Browse Ethernet OAM Event Log
- Monitoring > Ethernet OAM > Browse Ethernet OAM Statistics
- Monitoring > Port Access Control > RADIUS Authentication
- Monitoring > Port Access Control > RADIUS Account Client
- ACL > ACL Configuration Wizard
- ACL > Access Profile List
- ACL > ACL Finder
- ACL > CPU Filter Configuration Wizard
- ACL > CPU Filter Access Profile List
- ACL > CPU Filter Finder
- LLDP > LLDP Global Settings
- LLDP > Basic LLDP Port Settings
- LLDP > 802.1 Extension LLDP Port Settings
- LLDP > 802.3 Extension LLDP Port Settings
- LLDP > LLDP Management Address Settings
- LLDP > LLDP Statistics Table
- LLDP > LLDP Management Address Table
- LLDP > LLDP Local Port Table
- LLDP > LLDP Remote Port Table
- Appendix A - Ethernet Technology
- Appendix B - Ethernet Technology
- Appendix C – Rack mount Instructions
- Appendix D – Cables and Connectors
- Appendix E– Module Specs and Cable Lengths

4 Configuration DES-1210 Metro Ethernet Managed Switch User Manual
22
Media: When port number is 25 or 26. Select the Media is Copper, Fiber_1G or Fiber_100.
Speed: Gigabit Fiber connections can operate in 1000M Full Force Mode, Auto Mode or Disabled. Copper
connections can operate in Forced Mode settings (1000M Full, 100M Full, 100M Half, 10M Full, 10M Half),
Auto, or Disabled. 100M Fiber connections support 100M Full Force Mode, 100M Half Force Mode, or
Disabled. The default setting for all ports is Auto.
NOTE: Be sure to adjust port speed settings
appropriately after changing the connected cable
media types.
MDI/MDIX:
A medium dependent interface (MDI) port is an Ethernet port connection typically used on the Network
Interface Card (NIC) or Integrated NIC port on a PC. Switches and hubs usually use Medium dependent
interface crossover (MDIX) interface. When connecting the Switch to end stations, user have to use
straight through Ethernet cables to make sure the Tx/Rx pairs match up properly. When connecting the
Switch to other networking devices, a crossover cable must be used.
This switch provides a configurable MDI/MDIX function for users. The switches can be set as an MDI port in
order to connect to other hubs or switches without an Ethernet crossover cable.
Auto is designed on the switch to detect if the connection is backwards, and automatically chooses MDI or
MDIX to properly match the connection. The default setting is “Auto” MDI/MDIX.
Flow Control: You can enable this function to mitigate the traffic congestion. Ports configured for full-duplex
use 802.3x flow control, half-duplex ports use backpressure flow control. The default setting is Disabled.
System > Port Configuration > Port Description
In the Port Description page, the user may name various ports on the Switch.
Figure 4.21 – System > Port Configuration > Port Description
From Port / To Port: Specify the range of ports to describe.
Medium Type: When port number is 25 or 26. Select the Medium Type is Copper, Fiber_1G or Fiber_100.
Description: Specify the description of ports.
Click Apply to set the description in the table.
System > Port Configuration > Port Error Disabled
The Port Error Disabled page displays the information about ports that have had their connection status
disabled, for reasons such as STP loopback detection or link down status.
Figure 4.22 – System > Port Configuration > Port Error Disabled