User manual
Table Of Contents
- Table of Contents
- About This Guide
- 1 Product Introduction
- 2 Hardware Installation
- 3 Getting Started
- 4 Configuration
- Web-based Management
- Tool Bar > Save Menu
- Tool Bar > Tool Menu
- Tool Bar > Online Help
- Function Tree
- Device Information
- System > System Settings
- System > Serial Port Settings
- System > IPv6 System Settings
- System > IPv6 Route Settings
- System > IPv6 Neighbor Settings
- System > DHCP Auto Configuration
- System > Trap Settings
- System > Port Configuration > Port Settings
- System > Port Configuration > Port Description
- System > Port Configuration > Port Error Disabled
- System > SNMP Settings > SNMP Global State
- System > SNMP Settings > SNMP User Table
- System > SNMP Settings > SNMP Group Table
- System > SNMP Settings > SNMP View Table
- System > SNMP Settings > SNMP Community Table
- System > SNMP Settings > SNMP Host Table
- System > SNMP Settings > SNMP Engine ID
- System > SNMP Settings > SNMP Trap Settings
- System > User Accounts
- System > MAC Address Aging Time
- System > ARP Aging Time Settings
- System > PPPoE Circuit ID Insertion Settings
- System > Web Settings
- System > Telnet Settings
- System > Password Encryption
- System > Ping Test
- System > MAC Notification Settings
- System > System Log Configuration > System Log Settings
- System > System Log Configuration > System Log Server
- System > SMTP Service > SMTP Server Settings
- System > SMTP Service > SMTP Service
- Configuration > 802.1Q VLAN
- Configuration > 802.1Q Management VLAN
- Configuration > VLAN Status
- Configuration > GVRP Settings
- Configuration > GVRP Timer Settings
- Configuration > QinQ > QinQ Settings
- Configuration > QinQ > VLAN Translation CVID Entry Settings
- Configuration > 802.1v Protocol VLAN > 802.1v Protocol Group Settings
- Configuration > 802.1v Protocol VLAN > 802.1v Protocol VLAN Settings
- Configuration > VLAN Trunk Settings
- Configuration > Link Aggregation > Port Trunkings
- Configuration > Link Aggregation > LACP Port Settings
- Configuration > BPDU Protection Settings
- Configuration > IGMP Snooping > IGMP Snooping
- Configuration > IGMP Snooping > IGMP Access Control Settings
- Configuration > IGMP Snooping > ISM VLAN Settings
- Configuration > IGMP Snooping > Host Table
- Configuration > IGMP Snooping > IP Multicast Profile Settings
- Configuration > IGMP Snooping > Limited Multicast Range Settings
- Configuration > IGMP Snooping > Max Multicast Group Settings
- Configuration > MLD Snooping > MLD Snooping Settings
- Configuration > MLD Snooping > MLD Host Table
- Configuration > Port Mirroring
- Configuration > Loopback Detection
- Configuration > SNTP Settings > Time Settings
- Configuration > SNTP Settings > TimeZone Settings
- Configuration > DHCP/BOOTP Relay > DHCP/BOOTP Relay Global Settings
- Configuration > DHCP/BOOTP Relay > DHCP/BOOTP Relay Interface Settings
- Configuration > DHCP Local Relay Settings
- Configuration > DHCPv6 Relay Settings
- Configuration > Firmware Information
- Configuration > Spanning Tree > STP Bridge Global Settings
- Configuration > Spanning Tree > STP Port Settings
- Configuration > Spanning Tree > MST Configuration Identification
- Configuration > Spanning Tree > STP Instance Settings
- Configuration > Spanning Tree > MSTP Port Information
- Configuration > Ethernet OAM > Ethernet OAM Port Settings
- Configuration > Ethernet OAM > Ethernet OAM Event Configuration
- Configuration > DULD > DULD Port Settings
- Configuration > Multicast Forwarding & Filtering > Multicast Forwarding
- Configuration > Multicast Forwarding & Filtering > Multicast Filtering
- QoS > Traffic Control
- QoS > Bandwidth Control
- QoS > CoS Scheduling Mechanism
- QoS > CoS Output Scheduling
- QoS > 802.1p Default Priority
- QoS > 802.1p User Priority
- QoS > DSCP Priority Settings
- QoS > Priority Settings
- QoS > MAC Priority Settings
- QoS > IP Priority Settings
- QoS > IPv6 Priority Settings
- QoS > IPv6 Traffic Class Priority Settings
- QoS > TCP/UDP Port Priority Settings
- QoS > VLAN ID Priority Settings
- QoS > Protocol Priority Settings
- RMON > RMON Basic Settings
- RMON > RMON Ethernet Statistics Configuration
- RMON > RMON History Control Configuration
- RMON > RMON Alarm Configuration
- RMON > RMON Event Configuration
- Security > Trusted Host
- Security > Safeguard Engine
- Security > ARP Spoofing Prevention
- Security > Gratuitous ARP
- Security > Port Security
- Security > SSL Settings
- Security > Smart Binding > Smart Binding Settings
- Security > Smart Binding > Smart Binding
- Security > Smart Binding > White List
- Security > Smart Binding > Black List
- Security > Smart Binding > DHCP Snooping List
- Security > 802.1X > 802.1X Settings
- Security > 802.1X > 802.1X User
- Security > 802.1X > 802.1X Authentication RADIUS
- Security > 802.1X > 802.1X Guest VLAN
- Security > MAC Address Table > Static MAC
- Security > MAC Address Table > Dynamic Forwarding Table
- Security > Access Authentication Control > Authentication Policy Settings
- Security > Access Authentication Control > Application Authentication Settings
- Security > Access Authentication Control > Authentication Server Group
- Security > Access Authentication Control > Authentication Server
- Security > Access Authentication Control > Login Method Lists
- Security > Access Authentication Control > Enable Method Lists
- Security > Access Authentication Control > Local Enable Password Settings
- Security > Traffic Segmentation
- Security > DoS Prevention Settings
- Security > DHCP Server Screening > DHCP Server Screening Port Settings
- Security > DHCP Server Screening > Filter DHCP Server
- Security > SSH Settings > SSH Settings
- Security > SSH Settings > SSH Authmode and Algorithm Settings
- Security > SSH Settings > SSH User Authentication Lists
- Monitoring > Statistics
- Monitoring > Session Table
- Monitoring > CPU Utilization
- Monitoring > Memory Utilization
- Monitoring > Port Utilization
- Monitoring > Packet Size
- Monitoring > Packets > Transmitted (TX)
- Monitoring > Packets > Received (RX)
- Monitoring > Packets > UMB Cast (RX)
- Monitoring > Errors > Received (RX)
- Monitoring > Errors > Transmitted (TX)
- Monitoring > Cable Diagnostics
- Monitoring > System Log
- Monitoring > Browse ARP Table
- Monitoring > Ethernet OAM > Browse Ethernet OAM Event Log
- Monitoring > Ethernet OAM > Browse Ethernet OAM Statistics
- Monitoring > Port Access Control > RADIUS Authentication
- Monitoring > Port Access Control > RADIUS Account Client
- ACL > ACL Configuration Wizard
- ACL > Access Profile List
- ACL > ACL Finder
- ACL > CPU Filter Configuration Wizard
- ACL > CPU Filter Access Profile List
- ACL > CPU Filter Finder
- LLDP > LLDP Global Settings
- LLDP > Basic LLDP Port Settings
- LLDP > 802.1 Extension LLDP Port Settings
- LLDP > 802.3 Extension LLDP Port Settings
- LLDP > LLDP Management Address Settings
- LLDP > LLDP Statistics Table
- LLDP > LLDP Management Address Table
- LLDP > LLDP Local Port Table
- LLDP > LLDP Remote Port Table
- Appendix A - Ethernet Technology
- Appendix B - Ethernet Technology
- Appendix C – Rack mount Instructions
- Appendix D – Cables and Connectors
- Appendix E– Module Specs and Cable Lengths
4 Configuration DES-1210 Metro Ethernet Managed Switch User Manual
104
1) After selecting the Profile ID and Frame Type (MAC, IPv4, IPv6 or Packet content ACL), specify
attributes like Untagged/Tagged (for MAC), ICMP/IGMP/TCP/UDP/Protocol ID (for IPv4), or
ICMPv6/TCP/UDP (for IPv6), then click Select and a simplified frame diagram will be displayed.
2) Select the field of interest and related columns will be displayed in lower part of the page. Enter the
filtering mask and click Create when done. A filtering mask is to specify the digit that you want to check. For
example, if you want to check a network of 192.168.1.0/24, then you should enter the IP mask as
255.255.255.0.
NOTE: You cannot select Payload in a MAC ACL,
or L2 Header in IP ACL.
3) After the Profile ID has been created, it will go back to the main Access Profile List page.
ACL > ACL Finder
The ACL Finder page is used to help user to find a previously configured ACL entry. To search for an entry,
enter the Profile ID from the drop-down menu, select a port that you wish to view and click Find. The table
on the lower half of the screen will display the entries. To delete an entry click the corresponding Delete
button.
Figure 4.173 - ACL > ACL Finder
ACL > CPU Filter Configuration Wizard
The CPU Filter Configuration Wizard will aid with the creation of CPU Filter Rules.
Figure 4.174 - ACL > CPU Filter Configuration Wizard
From: Specify the origin of accessible packets. The possible values are:
Any - Indicates CPU Filter action will be on packets from any source.
MAC Address - Indicates CPU Filter action will be on packets from this MAC address.
IPv4 Addresses - Indicates CPU Filter action will be on packets from this IPv4 source address.
IPv6 - Indicates CPU Filter action will be on packets from this IPv6 source address.
To: Specify the destination of accessible packets. The possible values are:
Any - Indicates CPU Filter action will be on packets to any source.