Ver. 1.
D-Link Web Smart Switch User Manual Table of Contents Table of Contents ............................................................................................................................................. i About This Guide............................................................................................................................................. 1 Terms/Usage............................................................................................................................
D-Link Web Smart Switch User Manual System > System Settings ....................................................................................................................... 22 System > Port Settings............................................................................................................................. 23 System > Trap Settings For SmartConsole.............................................................................................. 23 System > Password Access Control ......
D-Link Web Smart Switch User Manual About This Guide This guide provides instructions to install the D-Link Fast Ethernet EasySmart Switch DES-1100-16/24, how to use the Web Utility, and to configure Web-based Management step-by-step. Note: The model you have purchased may appear slightly different from the illustrations shown in the document.
D-Link Web Smart Switch User Manual 1 Product Introduction Thank you and congratulations on your purchase of D-Link EasySmart Switch Products. D-Link's next generation EasySmart Ethernet switch series blends plug-and-play simplicity with exceptional value and reliability for small and medium-sized business (SMB) networking. All models are housed in a new style rack-mount metal case with easy-to-view front panel diagnostic LEDs.
D-Link Web Smart Switch User Manual Power LED: The Power LED lights up when the Switch is connected to a power source. Link/Act/Speed LED (Ports 1-24): Flashing: Indicates a network link through the corresponding port. Blinking: Indicates that the Switch is either sending or receiving data to the port. Green: Indicates that the port is running at 100M. Light off: Indicates that the port is running at 10M. Reset: Press the reset button to reset the Switch back to the default settings.
D-Link Web Smart Switch User Manual 2 Hardware Installation This chapter provides unpacking and installation information for the D-Link EasySmart Switch. Step 1: Unpacking Open the shipping carton and carefully unpack its contents. Please consult the packing list located in the User Manual to make sure all items are present and undamaged. If any item is missing or damaged, please contact your local D-Link reseller for replacement.
D-Link Web Smart Switch User Manual Figure 6 – Attach the mounting brackets to the Switch Then, use the screws provided with the equipment rack to mount the switch in the rack. Figure 7 – Mount the Switch in the rack or chassis Please be aware of following safety Instructions when installing: A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient.
D-Link Web Smart Switch User Manual Step 3 – Plugging in the AC Power Cord Users may now connect the AC power cord into the rear of the switch and to an electrical outlet (preferably one that is grounded and surge protected). Figure 8 –Plugging the switch into an outlet Power Failure As a precaution, the switch should be unplugged in case of power failure. When power is resumed, plug the switch back in. Grounding the Switch This section describes how to connect the EasySmart Switch to ground.
D-Link Web Smart Switch User Manual 3 Getting Started This chapter introduces the management interface of D-Link EasySmart Switch. Management Options The D-Link EasySmart Switch can be managed through any port on the device by using the Web-based Management or through any PC using the SmartConsole Utility. Each switch must be assigned its own IP Address, which is used for communication with Web-Based Management. The PC’s IP address should be in the same range as the switch.
D-Link Web Smart Switch User Manual Figure 10 –Connected Ethernet cable Login Web-based Management In order to login and configure the switch via an Ethernet connection, the PC must have an IP address in the same subnet as the switch. For example, if the switch has an IP address of 10.90.90.90, the PC should have an IP address of 10.x.y.z (where x/y is a number between 0 ~ 254 and z is a number between 1 ~ 254), and a subnet mask of 255.0.0.0.
D-Link Web Smart Switch User Manual NOTE: Please be sure to uninstall any existing SmartConsole Utility from your PC before installing the latest SmartConsole Utility. Option 1: Follow these steps to install the SmartConsole Utility via the autorun program on the installation CD. 1. Insert the Utility CD into your CD-Rom/DVD-Rom Drive. 2. The autorun program will appear automatically. 3. Click on the ”Install SmartConsole Utility” button and an installation wizard will guide you through the process. 4.
D-Link Web Smart Switch User Manual 4 SmartConsole Utility The D-Link SmartConsole Utility allows the administrator to quickly discover all D-Link Smart Switches and EasySmart Switches which are in the same domain of the PC, collect traps and log messages, and quick access to basic configurations of the switch. The SmartConsole Utility consists of three parts, Device Configurations at the top, Device List as the main body, and SmartConsole Settings at the left.
D-Link Web Smart Switch User Manual NOTE: If the Group Interval is set to 0, IGMP Snooping must be disabled in the Switch or the switches will not be discovered. Log Click this icon to launch the Log window. Click View Log to show the events of the SmartConsole Utility and the device. Date/Time indicates when the message was received, IP denotes where it comes from and Status shows the content of this log message. Click Clear Log to clear all log entries. Click OK to exit.
D-Link Web Smart Switch User Manual File By clicking on this icon you will see below options: Figure 17 – SmartConsole File Monitor Save: Records the setting of the Device List as default for the next time the SmartConsole Utility is used. Monitor Save As: Records the setting of the Device List in an appointed filename and file path. Monitor Load: Manually load a Device List setting file. Help Click this icon to launch the SmartConsole Info window.
D-Link Web Smart Switch User Manual Device Configuration The Device Configuration in the SmartConsole Utility has five icons: Device Settings Device Password Manager Multi Firmware Upgrade DHCP Refresh Web Access and the , , device buttons for the Device List. Device Settings Select a switch from the Device List. Click on this icon to launch the Device Settings window.
D-Link Web Smart Switch User Manual 14
D-Link Web Smart Switch User Manual Device Password Manager Select a switch from the Device List. Click on this icon to launch the Device Password Manager window. Here you can enter a new password and confirm it. Figure 20 – SmartConsole Device Password Manager Multi Firmware Upgrade The EasySmart switches’ firmware cannot be upgraded by clicking the Multi Firmware Upgrade button via SmartConsle Utility.
D-Link Web Smart Switch User Manual Figure 23 – SmartConsole Add device Figure 24 – SmartConsole Delete device Device List This list displays all discovered Web Smart and EasySmart switches on the network. Figure 25 – SmartConsole Device List Definitions of the Device List features: Monitor: Check the Monitor box and the SmartConsole will collect the trap and log data from the device. The in the monitor means the device was discovered by SmartConsole.
D-Link Web Smart Switch User Manual Gateway: Displays the Gateway setting of the device. Device Group Interval: Displays the intervals (in seconds). This feature is not available for EasySmart switches. Firmware version: Displays the current Firmware version of this device. LLDP: Displays the LLDP (Link Layer Discovery Protocol) status of the device. This feature is available only for PoE models of Web Smart switches. SNMP: Displays the SNMP status of the device.
D-Link Web Smart Switch User Manual 5 Configuration The features and functions of the D-Link EasySmart Switch can be configured for optimum use through the Web-based Management Utility. Web-based Management After a successful login you will see the screen below: Tool Bar Function Tree Main Configuration Screen Figure 26 – Web-based Management Above is the Web-based Management screen. The three main areas are the Tool Bar on top, the Function Tree, and the Main Configuration Screen.
D-Link Web Smart Switch User Manual Tool Bar > Save Menu The Save Menu provides Save Configuration. Figure 27 – Save Menu Save Configuration Select to save the entire configuration changes you have made to the device to switch’s non-volatile RAM. Figure 28– Save Configuration Tool Bar > Tool Menu The Tool Menu offers global function controls such as Reset System, Reboot Device, Firmware Upgrade and Configuration Backup & Restore.
D-Link Web Smart Switch User Manual Figure 32 – Tool Menu > Firmware upgrade Click Browse to browse your inventories for a saved firmware file. And then click Upgrade to restore the selected firmware file. CAUTION: Do not disconnect the PC or remove the power cord from device until upgrade is complete. The Switch may crash if the Firmware Upgrade is incomplete.
D-Link Web Smart Switch User Manual Function Tree All configuration options on the switch are accessed through the Setup menu on the left side of the screen. Click on the setup item that you want to configure. The following sections provide more detailed description of each feature and function. Figure 34 –Function Tree Device Information The Device Information provides an overview of the switch which includes essential information such as firmware, hardware and IP address.
D-Link Web Smart Switch User Manual Figure 35 – Device Information System > System Settings The System Setting allows the user to configure the IP address and the basic system information of the Switch. IP Information: There are two ways for the switch to obtain an IP address: Static and DHCP (Dynamic Host Configuration Protocol). When using static mode, the IP Address, Subnet Mask and Gateway can be manually configured.
D-Link Web Smart Switch User Manual System > Port Settings In the Port Setting page, the status of all ports can be monitored and adjusted for optimum configuration. By selecting a range of ports (From Port and To Port), the Speed can be set for all selected ports, effective by clicking Apply. Press the Refresh button to view the latest information.
D-Link Web Smart Switch User Manual Select the event message(s) to be sent out to the managing station.
D-Link Web Smart Switch User Manual If the IGMP server is not able to send out query control message automatically, a static router port may be required to be configured manually. Select the ports to be assigned as router ports for IGMP snooping in the IGMP Static Router Port List, and click Apply for changes to take effect.
D-Link Web Smart Switch User Manual switchs. The Switch will automatically shutdown the port and sends a log to the administrator. The Loopback Detection port will be unlocked when the Loopback Detection Recover Time times out. The Loopback Detection function can be implemented on a range of ports at a time. You may enable or disable this function using the pull-down menu.
D-Link Web Smart Switch User Manual Figure 45 – L2 Features > Statistics menu Transmit Packet & Collision: Number of transmit packets resulting in collision. Figure 46 – L2 Features > Statistics menu Receive Packet & Drop Packet: Number of receive packets resulting in drop packets.
D-Link Web Smart Switch User Manual Figure 47 – L2 Features > Statistics menu Receive Packet & CRC Packet: Number of receive packets resulting in CRC error. Figure 48 – L2 Features > Statistics menu Refresh All: Refreshes the details collected and displayed. Clear All Counters: Resets the details displayed. VLAN > 802.1Q VLAN A VLAN is a group of ports that can be anywhere in the network, but communicate as though they were in the same area.
D-Link Web Smart Switch User Manual VLANs can be easily organized to reflect department groups (such as R&D, Marketing), usage groups (such as e-mail), or multicast groups (multimedia applications such as video conferencing), and therefore help to simplify network management by allowing users to move devices to a new VLAN without having to change any physical connections. By default, 802.1Q VLAN is disabled. With 802.
D-Link Web Smart Switch User Manual Rename: Click to rename the VLAN group. Delete VID: Click to delete the VLAN group. Figure 52 – VLAN > 802.1Q VLAN > VLAN Table NOTE: When 802.1Q VLAN is enabled, the PortBased VLAN settings will be reset to default. VLAN > Port-Base VLAN Port-Based VLANs are the simplest and most common form of VLAN. It assigns the appliance LAN ports to VLANs, effectively transforming the appliances. You can assign multiple ports to the same VLAN, or each port to a separate VLAN.
D-Link Web Smart Switch User Manual Add VLAN: Click to create a new VLAN name and to select VLAN ports. The VLAN name should be less than 10 characters. To save the members in a group, click Apply. Rename: Click to rename the VLAN group. Delete VID: Click to delete the VLAN group. NOTE: When Port-Based VLAN is enabled, the 802.1Q VLAN settings will be reset to default. By default, all ports are untagged. QoS > 802.1p Default Priority QoS is an implementation of the IEEE 802.
D-Link Web Smart Switch User Manual Figure 55 – QoS > Storm Control Storm Control Type: User can select the different Storm type from Broadcast Only, Multicast & Broadcast, and Multicast & Broadcast & Unknown Unicast. Threshold (pps): If storm control is enabled (by default it is disabled), the threshold can be set from 0.8 to 12.6Kbits per second at 10Mbps speed, and 8 ~ 126Kbits per second at 100Mbps speed. Click Apply for the settings to take effect.
D-Link Web Smart Switch User Manual From Port / To Port: A consecutive group of ports may be configured starting with the selected port. Type: This drop-down menu allows you to select between RX (receive), TX (transmit), and Both. This setting will determine whether the bandwidth ceiling is applied to receiving, transmitting, or both receiving and transmitting packets. No Limit: This drop-down menu allows you to specify that the selected port will have no bandwidth limit. Enabled disables the limit.
D-Link Web Smart Switch User Manual Figure 58 – Security > Dynamic Forwarding Table 34
D-Link Web Smart Switch User Manual Appendix A - Ethernet Technology This chapter will describe the features of the D-Link EasySmart Switch and provide some background information about Ethernet/Fast Ethernet/Gigabit Ethernet switching technology. Gigabit Ethernet Technology Gigabit Ethernet is an extension of IEEE 802.
D-Link Web Smart Switch User Manual Appendix B - Technical Specifications Up to 2 queues per port Bandwidth Control Storm Control Hardware Specifications Key Components / Performance Switching Capacity: - DES-1100-16: 3.2Gbps - DES-1100-24: 4.8Gbps Max. Forwarding Rate - DES-1100-16: 2.38Mpps - DES-1100-24: 3.57Mpps Forwarding Mode: Store and Forward Packet Buffer memory:1.
D-Link Web Smart Switch User Manual Appendix C – Rack mount Instructions Safety Instructions - Rack Mount Instructions - The following or similar rack-mount instructions are included with the installation instructions: A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient.
