DES-1005D 5-Port 10/100Mbps Switch Manual RECYCLABLE V4.
TABLE OF C ONTENTS ABOUT THIS GUIDE .......................................................................1 PURPOSE.............................................................................................1 INTRODUCTION ..............................................................................2 FAST ETHERNET TECHNOLOGY .........................................................2 SWITCHING TECHNOLOGY .................................................................2 FEATURES ........................
A BOUT T HIS G UIDE Congratulations on your purchase of the D-Link DES-1005D. This device integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities in one high-performance, easy-to-use solution. Purpose This manual will familiarize you with the DES-1005D and guide you through the installation process.
I NTRODUCTION Fast Ethernet Technology The growing importance of LANs and the increasing complexity of desktop computing applications are fueling the need for high performance networks. 100BASE-T (Fast Ethernet) provides a cost-effective and highperformance solution for small workgroups, SMBs (Small to Medium Businesses), and any network supporting bandwidth-intensive applications.
multiple segments is one of the most common ways of increasing available bandwidth. If segmented correctly, most network traffic will remain within a single segment, enjoying the full-line speed bandwidth of that segment. Switches provide full-line speed and dedicated bandwidth for all connections. This is in contrast to hubs, which use the traditional shared networking topology, where the connected nodes contend for the same network bandwidth.
Features The DES-1005D is a high performance switch designed specifically for environments where traffic on the network and the number of users increase continuously. The DES-1005D, with its small, compact size, was specifically designed for small to mid-sized workgroups. The DES-1005D can be installed where space is limited; moreover, it provides immediate access to a rapidly growing network through a wide range of user-reliable functions.
Nway Auto-negotiation for any port. This allows for auto-sensing of speed (10/100Mbps), providing an automatic and flexible solution for the network. Flow control for any port. This minimizes dropped packets by sending out collision signals when the port’s receiving buffer is full. Data filtering rate eliminates all error packets, runts, etc., per port at wire-speed for 100Mbps operation and 10Mbps operation.
U NPACKING AND S ETUP Unpacking Open the box and carefully unpack it. The box should contain the following items: One DES-1005D: 5-port 10/100Mbps Ethernet Switch One External Power Adapter Wall Mount Kit CD Quick Installation Guide If any item is missing or damaged, please contact your local reseller for a replacement. Setup The setup of the DES-1005D can be performed using the following steps: The power outlet should be within 1.82 meters (6 feet) of the Switch.
I DENTIFYING E XTERNAL C OMPONENTS Front Panel The figure below shows the front panel of the DES-1005D. DES-1005D 10/100Mbps Fast Ethernet Switch LED Indicators Power Indicator: This green indicator light is on when the Switch is receiving power; otherwise, it is off. Link/Act: This LED indicator light is green when the port is connected to a device. The green indicator blinks as data is transmitted or received.
Rear Panel DES-1005D 10/100Mbps Fast Ethernet Switch Auto MDI/MDI-X Ports: All ports support automatic MDI/MDI-X crossover detection. The AutoMDI/MDI-X function makes it simple to connect to the switch—just plug either a Crossover or Straight-Through CAT5 cable into any port. Power Jack: Power is supplied through an external power adapter. Check the technical specification section for information about the power input voltage.
CONNECTING THE SWITCH PC to DES-1005D A computer can be connected to the DES-1005D via a two-pair Category 3, 4, 5 UTP/STP Straight-Through or Crossover cable. A computer equipped with a RJ-45 10/100Mbps port can be connected to any of the five DES1005D ports. The LED indicators for the PC connection depend on the capability of the computer’s Ethernet card.
Port Speed & Duplex Mode After plugging the selected cable to a specific port, the system uses autonegotiation to determine the transmission mode, auto-detecting the network speed (10Mbps or 100Mbps) for any new twisted-pair connection. If the attached device does not support auto-negotiation or has autonegotiation disabled, an auto-sensing process is initiated to select the speed and half-duplex mode is selected.
M OUNTING THE S WITCH ON A WALL The DES-1005D can also be mounted on a wall. Two mounting slots are provided on the bottom of the switch for this purpose. Please make sure that the front panel is exposed in order to view the LEDs. Please refer to the illustration below: A.) Mounting on a cement wall 1. 2. 3. Mount the Nylon screw anchors into a cement wall. Drive the T3 x 15L screws into the Nylon screw anchors.
C.) Mounting on a metal wall 1. Mount the magnetic base screws (optional) onto the mounting holes of the switch. 2. Attach the switch to a metallic surface. 3. The magnet kit is optional and is not included in the package contents.
T ECHNICAL S PECIFICATIONS General Standards IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet Protocol CSMA/CD Data Transfer Rate Ethernet: 10Mbps (half duplex) 20Mbps (full-duplex) Fast Ethernet: 100Mbps (half duplex) 200Mbps (full- duplex) Topology Star Network Cables 10BASET: 2-pair UTP CAT. 3,4,5/5e (100 m), EIA/TIA568 100-ohm STP (100 m) 100BASE-TX: 2-pair UTP CAT.
Performance Transmission Method: Store-and-forward RAM Buffer 512Kbits (64KBytes) per device Filtering Address Table 2K entries per device Packet Filtering / Forwarding Rate: 10Mbps Ethernet: 14,880/pps MAC Address Learning: Automatic update 100Mbps Fast Ethernet: 148,800/pps 14
RJ-45 P IN S PECIFICATION The following diagram and tables show the standard RJ-45 receptacle/connector and their pin assignments.
