Table of Contents Table of Contents Product Overview......................................................... 4 Package Contents.................................................... 4 System Requirements.............................................. 4 Introduction............................................................... 5 Features................................................................... 6 Hardware Overview.................................................. 8 Connections......................
Table of Contents WDR D&N Fixed Dome Network Camera Installation................................................................... 86 Networking Basics..................................................... 88 Check your IP address........................................... 88 Statically Assign an IP address.............................. 89 Reset and Restore...................................................... 90 External I/O Port.........................................................
Section 1 - Product Overview Product PackageOverview Contents • D-Link DCS-6111 WDR D&N Fixed Dome Network Camera • Screws • CAT5 Ethernet Cable • I/O Connector Plug • Power Adapter • Alignment Stencil • Dome Enclosure • Manual and Software on CD • Ring Enclosure • Quick Install Guide • Screw Driver Note: Using a power supply with a different voltage than the one included with your product will cause damage and void the warranty for this product.
Section 1 - Product Overview Introduction The DCS-6111 is a fixed dome network camera for indoor, office or home use, and designed to target the middlemarket. With an ultra Wide Dynamic Range (WDR) CMOS sensor, the DCS-6111 is used to provide better performance surveillance results under different lighting conditions. It can be used in highly contrast environments such as a lobby, retail store, ATM and much more.
Section 1 - Product Overview Features • Powerful Surveillance - The DCS-6111 uses the WDR VGA Progressive CMOS technology that delivers exceptional picture quality. The Wide Dynamic Range capability achieves high resolution, more detailed images in high contrast lighting conditions (for example, strong backlight). With this sensor architecture, the DCS-6111 maintains a constant balance for different variations in illumination and significantly improves the quality of real-time videos.
Section 1 - Product Overview • Supported Protocols - The DCS-6111 supports IPv6, the latest version of the Internet Protocol and a wide variety of protocols such as RTSP, FTP, SMTP, NTP, HTTP and HTTPS. In addition, UPnP DDNS and LLTD protocols are supported for Windows Vista users. Users can sign up with one of the free Dynamic DNS services available on the web to assign a name and domain name to the camera (e.g.mycamera.dlinkddns. com).
Section 1 - Product Overview Hardware Overview Connections Focus Controller DC Power Connector The DC power connector is located on the side panel of the DCS-6111. This 12V DC single-socket, supplies power to the network camera. Zoom Controller Adjustment Screw Tilt Screw Reset Button Reset is initiated when the reset button is pressed once and held until the power LED flashes through its cycle twice.
Section 1 - Product Overview Hardware Overview LEDs Status LED Blinking Red: indicates power is being supplied to the camera. Solid Green: indicates that a connection has been established via Ethernet port. Blinking Green: indicates traffic movement in the camera. The Status LED will not glow if an Ethernet connection is not established.
Section 2 - Installation Hardware Installation When Mounting to a Ceiling Find a suitable place to install the camera using the alignment stencil. Place the camera at the desired operating location and insert the screws through the two holes located at the base of the camera. Use a screwdriver to tighten and secure. When Mounting to a Wall Find a suitable place to install the camera by using the alignment stencil to find a desired operating location on the wall.
Section 2 - Installation Network Deployment General Connection (without PoE) Connect the network camera to a switch via an Ethernet cable. Connect the supplied power cable from the camera to a power outlet. Connection with a PoE Switch If using a PoE switch, connect the network camera to the switch via an Ethernet cable, which will provide both power and data transmission over a single cable.
Section 2 - Installation Software Installation Turn on the computer and insert the D-Link DCS-6111 Autorun CD into the CD-ROM drive. The following step-by-step instructions displayed are shown when using Windows Vista® operating system. The steps and screens are similar when using other Windows operating systems. Click on Installation Wizard to begin software installation. The Installation Setup Wizard window will pop up. Click Next to continue.
Section 2 - Installation Click I Agree to accept the License Agreement. Click I Agree Click the Browse button if you would like to change the destination of installation. Otherwise, click Install to continue. Note: Installation may take several minutes to complete.
Section 2 - Installation To start the installation click Install. Note: The installation may take several minutes to complete. Click Install Click Finish to complete installation and the D-Link Installation Wizard window will pop up for camera configuration.
Section 3 - Configuration Configuring Your Camera with the Installation Wizard If the D-Link Installation Wizard window does not pop up after completion of software installation, click on the icon that was created in your Windows Start Menu. The Installation Wizard will appear and show the MAC address and IP address of your DCS-6111, which may appear to be different from the actual address depending on what your device is connected to.
Section 3 - Configuration Enter a password, and confirm the password for your admin acccount and click Next. Note: The default administrator username is admin and the password is left blank. The password can also be changed after installation.
Section 3 - Configuration PPPoE Setup The Network Type screen displays will pop up to ask if you want to setup PPPoE for the device. Click No for quick setup and skip to page 18. Note: By using PPPoE, users can virtually dial from one machine to another over an Ethernet network, establish a point to point connection between them and then securely transport data packets over the connection. Click No The PPPoE Setting screen displays.
Section 3 - Configuration Check the Get IP by DHCP Server automatically box to obtain a new IP address every time the camera starts up. Click Next to continue. Click Next Select UPnP Port Forwarding if your router supports this function. If not, choose Manual to manually enter your port numbers. Click Next to continue.
Section 3 - Configuration Click Next to continue. Click Next A window will pop up asking you if you want to access the DCS-6111 via mobile phone. Clicking Yes will set the video resolution to 176x144.
Section 3 - Configuration Click Apply to apply the settings listed in the window to the device. The application may take a few minutes to process. Click Apply A window will pop up to confirm that the application was successfully configured. Click OK to continue. A new window will pop up displaying the links/addresses to access your device. Click Add to my favorite to save the address and then click Exit to complete the installation.
Section 3 - Configuration Double-click DCS-6111 in the Installation Wizard window to launch the camera’s web configuration page. Note: Please see the user manual for more information. Enter admin as the default username and leave the password blank by default. Click OK to continue.
Section 3 - Configuration This section shows your camera’s live video. You can configure your settings using the buttons in the window. For more information on using the web configuration, please refer to the user manual.
Section 3 - Configuration Adjusting the Lens Based on the live image retrieved from the camera, adjust the camera lens by performing the following procedures: Adjusting the Viewing Angle Loosen the pan screw and turn the lens module left and right until the desired position is achieved. Tighten the pan screw once completed. Loosen the tilt screws on both sides of the camera, and turn the lens module up and down until the desired position is achieved; tighten the tilt screws once completed.
Section 3 - Configuration Attaching the Enclosure Once the lens is properly adjusted, rearrange the light shield so that it will not obstruct the lens during surveillance. Place the dome enclosure over the network camera so that the LED sticker on the dome enclosure is properly aligned with the camera’s LED. Insert the supplied screws into the two holes located at the base of the dome enclosure, tighten until secure. Place the ring enclosure over the dome enclosure.
Section 3 - Configuration Web-based Configuration Utility This section will show you how to configure your new D-Link Network Camera using the Web-based Configuration Utility. To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of your Network Camera (http://192.168.0.120) Note: In the example, this address is 192.168.0.120. Your address may differ. Type Admin in the user name field and leave the password blank by default.
Section 3 - Configuration Live Video As seen by Mozilla Firefox and Netscape users, Quick Time player is invoked to stream the live video.
Section 3 - Configuration Using RTSP Players Use one of the following media players that support RTSP streaming to view MPEG-4 streaming media. Quick Time Player Real Player VLC media player mpegable Player pvPlayer 1. Launch a RTSP player. 2. Choose File > Open URL. 3. Type the URL command in the text box and then click OK. URL command = rtsp://:/ Note: Please refer to pages 44-45 for the RSTP port settings and streaming files.
Section 3 - Configuration Using 3GPP Mobile Phones To view streaming media using mobile phones, make sure the Network Camera is setup on the Internet. To utilize this feature, please check the Network Settings for your camera. 1. Most of the players on 3GPP mobile phones do not support RTSP authentication. Make sure the authentication mode of RTSP streaming is set to Disable. For more information, see page 44. 2. The 3G network bandwidth is limited, therefore users cannot use large size videos.
Section 3 - Configuration Camera This section shows your camera’s live video. You can configure the settings using the buttons listed below. Logout: Logout the camera server and close the browser. Client Settings: Click this button to access the Client Settings. Snapshot: Capture a still picture of a video. Enable/Disable the digital zoom feature. After selecting this icon, a small pop-up window will appear (see below). Disable Digital Select this to disable the digital zoom feature.
Section 3 - Configuration 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1/2 Digital Zoom - Refer to the previous page for more information. 3/4 Start/Stop Recording - Click (#3) to start recording. Video clips will be recorded in MP4 format to your computer. Press the button again (#4) to stop recording. If you close your web browser, the video will stop recording.
Section 3 - Configuration Snapshot This page shows a snapshot image of a live video taken from DCS-6111 network camera.
Section 3 - Configuration Client Setup Select to access this section. To configure the settings for media streaming and recording, please read the following definitions. Stream Select which video stream profile to use. Options: Media There are 3 selectable Media Options for your stream Options: profile. The Default setting is Video and Audio. Protocol There are 4 protocols for you to choose for video Options: streaming.
Section 3 - Configuration Setup Wizard To quickly configure your network camera, click Internet Connection Setup Wizard. Otherwise, click Manual Internet Connection Setup to manually configure your network camera. To quickly configure your network camera’s motion detection settings, click Motion Detection Setup Wizard and skip to page 38. If you want to enter your settings without running the wizard, click Manual Motion Detection Setup and skip to page 41.
Section 3 - Configuration Select DHCP if you are unsure which settings to pick. Click Next to continue and skip to page 35. Click Next Select PPPoE if the camera is directly connected to the Internet through a DSL modem and your ISP (Internet Service Provider) requires you to use PPPoE for the Internet connection. Click Next to continue and skip to Step 2 on page 35.
Section 3 - Configuration Select Static IP if your Internet Service Provider has provided you with connection settings, or you wish to set a static address within your home network. Enter all the relevant LAN information. Click Next to continue. Click Next If you have selected PPPoE, enter your username and password. Click Next to continue.
Section 3 - Configuration With a Dynamic DNS account, the camera automatically updates your IP address. To enable DDNS, enter your host information. Click Next to continue. Click Next Enter a name for your camera and click Next to continue. Click Next Configure the correct time to ensure all the events will be triggered and scheduled at the correct time.Click Next to continue.
Section 3 - Configuration Once you have selected Dynamic, PPPoE, or Static, you will see a summary of your camera’s settings. Click Apply to save and activate your settings.
Section 3 - Configuration Motion Detection Setup Wizard This wizard will guide you through a step-by-step process to configure your new D-Link Camera’s motion detection functions. Click Next to begin the process. Click Next This screen will allow you to enable or disable the motion detection feature. Click New to create and draw the motion detection window.
Section 3 - Configuration Select the recording time and date for your camera. Click Next to continue. Note: Recording camera footage will take up space on your hard drive. It is recommended that you have sufficient disk space for Always function. Click Next This step allows you to specify your event notification, either via email or FTP. Enter the relevant information of your email account or FTP settings and then click Next to continue.
Section 3 - Configuration You have completed the Motion Detection Wizard. Click Apply to activate and save your settings.
Section 3 - Configuration Network Setup LAN Settings: Settings for your local area network. DHCP: Select this connection if you have a DHCP server running on your network and would like a dynamic IP address to be assigned to your camera automatically. Static IP Client: You may enter a static or fixed IP address for your camera. IP Address: Enter an IP address. Subnet Mask: The default value is “255.255.255.0.” This helps to determine if the designated IP address is on the same subnet.
Section 3 - Configuration Enabling UPnP port forwarding allows the Network Camera to open a secondary HTTP port on the router. You have to add the secondary HTTP port number behind the Network Camera’s public address in order to access the Network Camera from the Internet. For example, when the HTTP port is set to 80 and the secondary HTTP port is set to 8080, refer to the list below for the Network Camera’s IP address. From the Internet In a local area network http://203.67.124.123:8080 http://192.168.
Section 3 - Configuration Optional default Enter the IPv6 router address. router : Optional primary Enter the IPv6 DNS address. DNS : PPPoE Settings: Enable this setting if your ISP (DSL service) is using PPPoE. You may already have both Username and Password given by your ISP, or you may check with your ISP. The Connect Status will be determined automatically by the system. HTTP: You may configure two HTTP ports for your camera. HTTP ports allow you to connect to the camera via a standard web browser.
Section 3 - Configuration Access name for The default name is video2.mjpg. stream2: Access name for stream 1 / Access name for stream 2 : The access name is used to differentiate the streaming source. When using Mozilla Firefox or Netscape to access the Network Camera, and the video mode is set to JPEG, users will receive continuous JPEG pictures. This technology, known as "server push", allows the Network Camera to feed live pictures to Mozilla Firefox and Netscape.
Section 3 - Configuration The accessibility of the RTSP streaming for the three authentication modes are listed in the following table. Quick Time player Real Player VLC media player mpegable Player pvPlayer Disable O O O O O Basic O O X X X Digest O X X X X O indicates that the authentication mode is supported by the RTSP player. X indicates that the authentication mode is NOT supported by the RTSP player.
Section 3 - Configuration RTSP port: The port number that you use for RSTP streaming, the default port number is 554. RTP (Real Time Protocol) Port is used to streaming audio and video while RTCP (Real Time Control Protocol) port is used to monitor QoS of RTP stream. Note: RTP video port and RTP audio port must be an “even” number. The numbers of RTCP video port and RTCP audio port must equal to the numbers of RTP video port and RTP audio port, plus one repetitively.
Section 3 - Configuration For example, if some content is associated with group 239.1.1.1, the source will send data packets destined to 239.1.1.1. Receivers for that content will inform the network that they are interested in receiving data packets sent to the group 239.1.1.1. The receiver “joins” 239.1.1.1. The Multicast address ranges from 224.0.0.0 to 239.255.255.255, or, equivalently, 224.0.0.0/4 Multicast video Default port number is 5560, or please choose between 1024 and 65534.
Section 3 - Configuration Dynamic DNS DDNS (Dynamic Domain Name Server) will hold a DNS host name and synchronize the public IP address of the modem when it has been modified. The username and password are required when using the DDNS service. Enable DDNS: Click to enable the DDNS function. Server Name: Select your Dynamic DNS provider from the drop down menu. Host Name: Enter the host name of the DDNS server. Username: Enter your username or e-mail used to connect to the DDNS server.
Section 3 - Configuration Image Setup You may configure the image settings of the video for your network camera. A preview of the image will be shown in the window of Live Video. Click Save Settings to save and activate your changes. Color: Select either a Color or B/W (black and white, monochrome) video display. Power Line Select either 50 or 60Hz. Frequency: Video Orientation: Flip will vertically rotate the video. Mirror will horizontally rotate the video.
Section 3 - Configuration Enable WDR Select to enable the WDR function. WDR provides better performance especially when the image contains both very dark (Wide Dynamic and bright areas. Also helps the camera to cope with varying lighting conditions. Range): Note: When you select this function, Exposure level and AGC functions will be disabled. Switch to B/W Select to automatically enable the camera to switch to B/W night mode. (Night Mode): White Balance: Select either Auto or Fix from the drop-down box.
Section 3 - Configuration Audio and Video Settings for two video streams (stream 1 and stream 2) can be configured here. You may configure one setting for computer display and the other one for mobile display. Mode: Select either JPEG or MPEG4. In JPEG mode, the video frames are independent. However, MPEG4 consumes much less network bandwidth than JPEG. Frame Size: Select 176 x 144, 352 x 240 or 640 x 480 pixels for the frame size.
Section 3 - Configuration External Set the microphone input gain at either 0dB or 20dB. microphone input: Note: The higher the decibel number, the louder the sound. Audio type: Advanced Audio Coding (AAC) is a wide band audio coding algorithm that exploits two primary coding strategies to dramatically reduce the amount of data needed to convey high-quality digital audio. Select a higher bit rate number for better audio quality. AAC bit rate: Select an AAC bit rate from the drop-down list.
Section 3 - Configuration Motion Detection Once Motion Detection feature is enabled, users will be able to monitor three windows with different settings. This allows your camera to serve as a security device that records only when motion is detected. Enable motion Check this option to turn on the motion detection detection: feature. Window name: Create your own name for the monitored area/ window. It will show at the top of the motion window.
Section 3 - Configuration To enable motion detection, follow the steps below: 1. Click New to add a new motion detection window. 2. Enter a name in the Window Name field. 3. Define the sensitivity to moving objects and the space ratio of all alerted pixels by moving the Sensitivity and Percentage slide bar. 4. Click Save to apply the changes. 5. Select Enable motion detection to activate motion detection. Note: Drag to resize the window and click X to close the window.
Section 3 - Configuration How does motion detection work? A C B D There are two parameters for setting the motion detection: Sensitivity and Percentage. In the illustration above, frame A and frame B are two sequential images. Pixel differences between the two frames are detected and highlighted in gray (frame C), and will be compared with the sensitivity setting. Sensitivity is a value that expresses the sensitivity to moving objects.
Section 3 - Configuration Time and Date Automatically or manually configure, update, and maintain the internal system clock for your camera. Current Server Time: Displays current time. Time Zone: Select your time zone from the drop-down menu. Enable Daylight Select this to enable the daylight saving time Saving: (DST). During DST, the system clock moves one hour ahead. Note: To utilize this feature, ensure to set the time zone of your network camera.
Section 3 - Configuration Event Setup There are four sections in Event Setup page. • Event • Server • Media • Recording 1. To add a new item - event, server or media, click Add. A pop-up will appear and update the fields accordingly. 2. To delete the selected item from the pull-down menu of event, server or media, click Delete. 3. Click on the item name for further modification. Note: You can add up to four events, five servers and five media fields.
Section 3 - Configuration Application A typical application is that when motion is detected, the DCS-6111 Network Camera sends images to a FTP server or via e-mail as notifications. For example, as seen in the illustration below, an event can be triggered by many sources, such as motion detection or external digital input devices. When an event is triggered, you can specify what kind of action will be performed.
Section 3 - Configuration Add Server You may configure up to 5 servers for media storage. Server Name: Unique name of your server. Email: Select this to enable and apply your email account setting for your camera. FTP: Select this to access a granted folder on the external FTP server. HTTP: Select this to use a web server to store the media. Network Storage: Only one network storage device is supported.
Section 3 - Configuration Add Media There are three types of media-Snapshot, Video Clip and System Log. Media Name: Enter an unique name for media. Snapshot: Select this feature to enable camera to take snapshot. Source: The source of stream: stream1 or stream2. Send pre-event The number of pre-event images. image(s) [0~7]: Send post-event The number of post-event images. Refer page 61 for image(s) [0~7]: more information. File name prefix: The prefix name will be added on the file name.
Section 3 - Configuration Send post-event image (s) [0~7) Specify to capture the number of images after a trigger is activated. A maximum of seven images can be generated. For example: If both the Send pre-event images and Send post-event images are set to seven, a total of 15 images are generated after a trigger is activated. 1 pic. 2 pic. 3 pic. 4 pic. 5 pic. 6 pic. 7 pic. 8 pic. 9 pic. 10 pic. 11 pic. 10 pic. 12 pic. 13 pic. 14 pic. 15 pic. The moment the trigger is activated.
Section 3 - Configuration Maximum duration Specify the maximal recording duration in seconds. You can set up to ten seconds. For example: If the Pre-event recording is set to five seconds and the Maximum duration is set to ten seconds, the Network Camera continues to record for another four seconds after a trigger is activated. 1 sec. 2 sec. 3 sec. 4 sec. 5 sec. 6 sec. 7 sec. 8 sec. 9 sec. 10 sec. The moment the trigger is activated.
Section 3 - Configuration Add Event Create and schedule up to 3 events with their own settings here. Event name: Enter a name for the event. Enable this event: Select to activate this event. Priority: Set the priority for this event. The event with higher priority will be executed first. Delay: Select the delay time before checking next event. It is being used for both events of motion detection and digital input trigger. Trigger: The input type that triggers the event.
Section 3 - Configuration Add Recording Here you can configure and schedule the recording settings. Recording entry The unique name of the entry. name: Enable this Select this to enable the recording function. recording: Priority: Set the priority for this entry. The entry with a higher priority value will be executed first. Source: The source of stream. Recording Scheduling the recording entry. schedule: Recording Configuring the setting for the recording.
Section 3 - Configuration Advanced DI and DO The I/O connector provides the physical interface for digital output (DO) and digital input (DI) that is used for connecting such external alarm devices as IR-Sensors and alarm relays to the network camera. DI and DO: Settings for both Digital input signal and digital output signal can be configured here. Digital input Please select High or Low for digital input trigger trigger condition.
Section 3 - Configuration ICR ICR - IR-Cut Removable(ICR) filter is a switch mechanical design of two different sensor filters. It provides the best light conditions both during the day and night. The following options are: Auto: The Network Camera automatically switches between day and night mode by judging the level of ambient light. This mode is accessible only when the exposure mode is set to Auto.
Section 3 - Configuration HTTPS This section briefly describes about the HTTPS services provided by the network camera. Enable HTTPS Select to enable a secure HTTPS connection. secure connection: HTTP & HTTPS: Select to enable the HTTP and HTTPS services. By default, this option is enabled. HTTPS only: Select this to automatically redirect an HTTP connection to HTTPS. There are three methods to implement HTTPS. They are: Method 1.
Section 3 - Configuration Method 3. Create To upload a signed-certificate, ensure to certificate request create a certificate request. After creating and install: the request, click Browse to upload the certificate file which has been signed by the third party. Once uploaded, the Certificate Information section displays the information of the certificate and the status is changed to Active.
Section 3 - Configuration Access List The Access List page will allow you to configure access permissions for each user. Allow list: The list of IP addresses that have the access rights to the camera. Delete allow Remove the customized setting from the Allow list: List. Deny list: The list of IP addresses that have no access right to the camera. Delete deny Remove the customized setting from the Delete list: List. Always allow Select to enter an IP address.
Section 3 - Configuration For example: When the range of allowed list is set from 1.1.1.0 to 192.255.255.255 and the range of denied list is set from 1.1.1.0 to 170.255.255.255, Only users’ IP located between 171.0.0.0 and 192.255.255.255 can access the Network Camera. Alowed List Denied List There are three different IP formats to choose from the list. Click Add to save the IP formats. Single: Network: Range: Add a single IP address. Add a network IP addresses with subnet mask.
Section 3 - Configuration Maintenance Device Management You can modify both the camera’s name and the administrator’s password, as well as add more user accounts for accessing the camera. Admin password Modify the password for the administrator’s setup: account. Add user Add a new user account. account: Username: Enter a username for the new account. Password: Enter a password for the new account. Privilege: Select the access rights for the new user. Manage user: Manage the accounts for existing users.
Section 3 - Configuration Backup and Restore The Backup and Restore page will allow you to turn the front panel LED off, restore factory default settings, and reboot the camera. Turn off the LED Select this option to turn off the LED next to the indicator: lens. This will prevent anyone from observing the operation of the network camera. Restore: Click the Restore button to reset the camera back to its factory default settings. This will remove all the configuration settings that were previously made.
Section 3 - Configuration Firmware Update Your current firmware version and date will be displayed on your screen. You may go to the D-Link Support page to check for the latest firmware version available. To upgrade the firmware on your DCS-6111, please download and save the latest firmware version from the D-Link support site to your local hard drive. Locate the file on your local hard drive by clicking the Browse button. Then, open the file and click the “Upload” button to start the firmware upgrade.
Section 3 - Configuration Status Device Info This page displays all the details information about your device and network connection.
Section 3 - Configuration Logs This page displays the log information of your camera. You can configure a remote log server so that you can view your log details remotely. Enable remote log: Click to enable this feature so that the camera can send camera log files to a remote server. Log server settings: Configure the settings for the log server. IP Address: The IP address of the remote server. Port: The port number of the remote log server. The default port is 514. Save: Click to save the settings.
Section 3 - Configuration Help D-Link DCS-6111 User Manual 76
Section 3 - Configuration D-ViewCam Installation D-ViewCam software is included for the administrator to manage up to 32 D-Link network cameras remotely. The administrator can use the software to configure the advanced settings for the camera. D-ViewCam is a complete management tool and includes all configurative settings. Insert the CD into the CD-ROM drive. A menu screen will appear as shown below.
Section 3 - Configuration Click Next to continue. Click Next Click Browse if you would like to choose a specific folder for the installation. Otherwise, click Next to continue.
Section 3 - Configuration Click Next to start the installation. Note: The D-ViewCam installation process may take several minutes to complete. Click Next Click Finish to complete the installation.
Section 3 - Configuration Add a Camera This section will show you how to start and add a camera to the D-ViewCam system. To start D-ViewCam, select Start > All Programs > D-Link > D-Link D-ViewCam. Enter admin as the default username and leave the password to log into the system and access the Add blank. Click Camera Wizard. Note: Please refer to page 48 in the D-ViewCam user manual to change your password.
Section 3 - Configuration Welcome to the Add Camera Wizard. Use this wizard to add your cameras to the D-ViewCam system. Click to continue. Note: Use the left or right arrow to navigate the wizard.
Section 3 - Configuration Select a method to add your camera(s). You can select Auto Discovery to automatically search for your camera(s), or select Add Manually to add your camera(s) using the camera’s IP address. Click Next to continue. If you select Auto Discovery, the system will search all cameras that are located on the same LAN with same subnet. The system will place all the cameras at the default map called My Map. Click Next to continue.
Section 3 - Configuration D-ViewCam shows the detected network camera(s) information. You can select the recording mode for each camera. • 24/7 Continuous Recording: Continuously records 24 hours a day, 7 days a week. • 24/7 Motion Detection Recording: Continuously monitors, but only records when motion is detected. • Office Hours Only: Continuously monitors during office hours (8:00AM to 6:00PM), and only records when motion is detected.
Section 3 - Configuration Select Yes to add other cameras, or select No if you have no additional cameras to add. Click Next to continue. The Add Camera wizard is now complete. Click Close to access the D-ViewCam’s main screen. Your D-ViewCam Installation is Complete! Note: Please refer to the D-ViewCam user manual for information about using D-ViewCam.
Section 4 - Frequently Asked Questions Frequently Asked Questions This chapter provides solutions to problems that may occur during the installation and operation of the DCS-6111. Read the following descriptions if you are having any problems. WDR D&N Fixed Dome Network Camera Features 1. What is a WDR D&N Fixed Dome Network Camera? The WDR D&N Fixed Dome Network Camera is a stand-alone system connecting directly to an Ethernet or Fast Ethernet network.
Section 5 - Fixed Dome Day & Night Network Camera With WDR Sensor Installation WDR D&N Fixed Dome Network Camera Installation 1. Can the Network Camera be used outdoors? The WDR D&N Fixed Dome Network Camera is not weatherproof. It needs to be equipped with a weatherproof case for outdoor use but it is not recommended. 2.
Section 5 - Fixed Dome Day & Night Network Camera With WDR Sensor Installation 8. I connected the Network Camera directly to a computer with a cross-over Ethernet cable and received a Windows error upon running the Installation Wizard? • • This Windows error will occur if the WDR D&N Fixed Dome Network Camera is connected to a computer that is not properly configured with a valid IP address.
Appendix A - Networking Basics Networking Basics Check your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. (Windows Vista® users type cmd in the Start Search box.) At the prompt, type ipconfig and press Enter.
Appendix A - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/access point, or you need to assign a static IP address, please follow the steps below: Step 1 Windows Vista® - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections. ® Windows XP - Click on Start > Control Panel > Network Connections.
Appendix B - Reset and Restore Reset and Restore The hidden button in the pinhole beside the Ethernet socket is used to reset the system or restore the factory default settings. Sometimes resetting the DCS-6111 will return the system back to a normal state. If the system still has problems after reset, restore the factory settings and install again: RESET: 1. Lightly insert a paper clip (or a similar sized tool) into the reset hole on the back of the camera, press lightly and then release the button. 2.
Appendix B - External I/O Port External I/O Port DI/DO Diagram Pin 1~4 are used to connect with digital input and digital output devices. Refer to the following illustration for connection method. 12V DO+ PIN 1 Power+12V The DCS-6111 provides a general I/O terminal block with one digital input and one relay switch for device control. The relay switch of DO+ and DO- can be used to turn on or off the external device.
Appendix C - Technical Specifications Technical Specifications NETWORK PROTOCOL SUPPORT + IPv4, IPv6, TCP/IP, RTSP/ RTP/ RTCP, HTTP, HTTPS, SMTP, FTP, NTP, DNS, DHCP, UPnP, DDNS, PPPoE, IGMP, Samba client, IP Filtering, 3GPP, LLTD BUILT-IN NETWORK INTERFACES + 10/100BASE-TX Ethernet port, RJ45 VIDEO ALGORITHM SUPPORT + JPEG for still image + Compression: MJPEG & MPEG-4 + Streaming: Simultaneous dual-streaming + MPEG-4 streaming over UDP, TCP, or HTTP + MPEG-4 multicast streaming + MJPEG streaming over HTT
Appendix C - Technical Specifications + Real Player 10.5 OPERATION TEMPERATURE NETWORK INTERFACE + IEEE 802.3/802.3u 10/100BASE-TX Ethernet port + Supports half/full-duplex operations + Supports 802.3x Flow Control in full-duplex mode + Supports IEEE 802.3af PoE 0º to 40º C (32º to 104º F) STORAGE TEMPERATURE -20º to 70º C (-4º to 158º F) HUMIDITY AUDIO + Compression and bit rate: - GSM-AMR speech compression, bit rate: 4.75 kbps ~12.
