Table of Contents Table of Contents Product Overview......................................................... 4 Package Contents.................................................... 4 System Requirements.............................................. 4 Introduction............................................................... 5 Features.................................................................... 6 Hardware Overview.................................................. 8 Connections......................
Table of Contents Megapixel PoE Network Camera Features............... 80 Megapixel PoE Network Camera Installation........... 81 Networking Basics..................................................... 83 Check your IP address........................................... 83 Statically Assign an IP address.............................. 84 Reset and Restore...................................................... 85 External I/O Port.........................................................
Section 1 - Product Overview Product PackageOverview Contents • D-Link DCS-3110 Megapixel PoE Network Camera • CAT5 Ethernet Cable • Power Adapter • Screws • Manual and Software on CD • Quick Install Guide Note: Using a power supply with a different voltage than the one included with your product will cause damage and void the warranty for this product. If any of the above items are missing, please contact your reseller.
Section 1 - Product Overview Introduction DCS-3110 is an ideal network camera for professional surveillance and security applications. This camera adopts a 1.3 mega-pixel progressive scan CMOS sensor and the motion JPEG stream covers three times larger scene which is also at least three times higher than analog CCTV cameras. This is also a very important consideration in video surveillance applications, where a high resolution image helps to identify a criminal.
Section 1 - Product Overview Features • Powerful Surveillance - The DCS-3110 is designed to target the high-end surveillance market. As mentioned earlier, a 1.3 mega-pixel progressive scan CMOS sensor covers three times larger view. The DCS-3110 is a powerful network camera for both day and night applications. It effectively reduces motion blur and distortion as well as jagged edges of recorded images.
Section 1 - Product Overview • Supported Protocols - DCS-3110 supports a wide variety of protocols such as RTSP, FTP, SMTP, NTP and HTTP. In addition, the camera supports UPnP and DDNS. • Web Configuration - Using a Web browser, administrators can configure and manage the network camera directly from its own web page via your network or the Internet. Up to 20 user accounts can be created with privilege settings controlled by the administrator.
Section 1 - Product Overview Hardware Overview Connections Microphone Connector: The camera has an internal built-in microphone. To use an external microphone, plug it into the microphone connector. Status LED Blinking Red: indicates power is being supplied to the camera. Solid Green: indicates that a connection has been established via Ethernet port. Blinking Green: indicates traffic movement in the camera. If the Ethernet connection is not established the Status LED will not glow.
Section 1 - Product Overview Interfaces Front View ICR and Built-in Microphone IR-Cut Removable (ICR) Sensor The IR-Cut removable sensor will judge the light conditions and then switches from color to B/W accordingly. Compact Flash Card Slot Built-in Microphone CF card slot CompactFlash (CF) is a mass storage device format used in portable electronic devices. The CF card slot can be seen at the side of the network camera. Note: Ensure to remove the rubber strip before using it.
Section 2 - Hardware Installation Hardware Installation Connect the Ethernet Cable Connect an Ethernet cable to the Ethernet port located on the Network Camera’s back panel and attach it to the network. Connect Using Power-Over-Ethernet Once you connect an Ethernet cable to your PoE switch or adapter, the Power LED on the DCS-3110 will turn green to indicate a proper connection.
Section 2 - Hardware Installation The package comes with a camera stand with a swivel ball screw head that can be attached to the Network Camera bottom socket cavity. Attach the camera stand to the Network Camera and station it for your application. There are holes located in the base of the camera stand allowing the camera to be mounted to the ceiling, or any wall securely.
Section 3- Software Installation Software Installation Turn on the computer and insert the D-Link DCS-3110 CD into the CD-ROM drive. The following step-by-step instructions displayed are shown when using Windows Vista® operating system. The steps and screens are similar when using other Windows® operating systems. Click on Installation Wizard The Installation Setup Wizard window will pop up. Click Next to continue.
Section 3- Software Installation Click I Agree to accept the License Agreement. Click I Agree Click the Browse button if you would like to change the destination of installation, otherwise click Install to continue. Note: Installation may take several minutes to complete.
Section 3- Software Installation Click Finish to complete installation and the D-Link Installation Wizard window will pop up for camera configuration.
Section 4 - Configuration Configuration Installation Wizard If the D-Link Installation Wizard window does not pop up after completion of software installation, click on the icon that was created in your Windows Start Menu. The Installation Wizard will appear and show the MAC address and IP address of the DCS-3110, which may appear to be different from the actual address depending on what your device is connected to.
Section 4 - Configuration Enter a password, and confirm the password for the admin ID and click Next. Note: The default administrator username is set to admin and the password may be left blank. The password can be changed after installation.
Section 4 - Configuration PPPoE Setup The Network Type prompt will pop up to ask if you want to setup a PPPoE for the device. Click No for quick setup and skip to the next page. Note: By using PPPoE, users can virtually dial from one machine to another over an Ethernet network, establish a point to point connection between them and then securely transport data packets over the connection. If you have selected Yes, enter the username and password provided by your ISP to connect to the Internet by PPPoE.
Section 4 - Configuration Check the Get IP by DHCP Server automatically box to obtain a new IP address every time the camera starts up. Click Next to continue. Click Next Select UPnP Port Forwarding if your router supports this function. If not, choose Manual to manually enter your port numbers. Click Next to continue.
Section 4 - Configuration Select Enable DDNS if you have subscribed to a Dynamic DNS account and would like your camera to update its IP address automatically. Enter all the relevant account information. Click Next to continue. Click Next A window will pop up asking you if you want to access the DCS-3110 via mobile phone. Clicking Yes will set the video resolution to 176x144. Click No to continue.
Section 4 - Configuration Click Apply to save and activate the settings listed in the window to the device. Application may take a few minutes to process. Click Apply A window will pop up to confirm the installation was successful. Click OK to continue. A new window will pop up displaying the lists to access your device, click Add to my favorite to save the address and then click Exit to complete installation.
Section 4 - Configuration Double-click DCS-3110 in the Installation Wizard window to launch the camera’s web configuration utility. Enter admin as the default username and leave the password blank. Click OK to continue. Note: If you have changed your password, please enter your new password.
Section 4 - Configuration This section shows your camera’s live video. You can control your settings using the buttons below.
Section 4 - Configuration Web-based Configuration Utility This section will show you how to configure your new D-Link Network Camera using the Web-based Configuration Utility. To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of your Network Camera (http://192.168.0.120) Note: In the example, this address is 192.168.0.120. Your address may differ. Type Admin in the user name field and leave the password blank by default. Click OK to continue.
Section 4 - Configuration Live Video As seen by Mozilla Firefox and Netscape users, Quick Time player is invoked to stream the live video.
Section 4 - Configuration Using RTSP Players Use one of the following media players that support RTSP streaming to view MPEG-4 streaming media. Quick Time Player Real Player VLC media player mpegable Player pvPlayer 1. Launch a RTSP player. 2. Choose File > Open URL. 3. Type the URL command in the text box and then click OK. URL command = rtsp://:/ Note: Please refer to pages 39-44 for the settings of your RTSP port and stream files.
Section 4 - Configuration Using 3GPP Mobile Phones To view streaming media using mobile phones, make sure the Network Camera is setup on the Internet. To utilize this feature, please check the Network Settings for your camera. 1. Most of the players on 3GPP mobile phones do not support RTSP authentication, make sure the authentication mode of RTSP streaming is set to Disable. For more information, see RTSP Streaming on page 42. 2.
Section 4 - Configuration Camera This section shows your camera’s live video. You can control your settings using the buttons below. Client Settings: Click this button to access the Client Settings. Snapshot: Captures a still picture of a video. Logout: Logout the camera server and close the browser. Enable/Disable the digital zoom feature. After selecting this icon, a small pop-up window will appear (see below). Disable Digital Zoom: Select this to disable the digital zoom feature.
Section 4 - Configuration 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1/2 Digital Zoom - Refer to the previous page for more information. 3/4 Start/Stop Recording - Click to start recording. Video clips will be recorded in MP4 format to your computer. Press the button again (#4) to stop recording. If you close your web browser, the video will stop recording.
Section 4 - Configuration Snapshot After you have clicked Snapshot a pop-up window with an image of live video taken by the DCS-3110 will appear.
Section 4 - Configuration Client Setup To configure the settings for media streaming and recording, please read the following definitions. Stream Options: Select which video stream profile to use. Protocol There are 4 protocols for you to choose for video Options: streaming. UDP Protocol: This is recommended because it is an ideal protocol for transmitting real-time audio and video data, which can tolerate some lost packets. UDP Unicast: Stream to a single computer.
Section 4 - Configuration Setup Wizard To quickly configure your network camera, click Internet Connection Setup Wizard or click Manual Internet Connection Setup to manually configure your network camera. To quickly configure your network camera’s motion detection settings, click Motion Detection Setup Wizard and skip to page 36. If you want to enter your settings without running the wizard, click Manual Motion Detection Setup and skip to page 49.
Section 4 - Configuration Select DHCP if you are unsure which settings to pick. Click Next to continue and skip to page 34. Click Next Select PPPoE if the camera is directly connected to the Internet through a DSL modem and your ISP (Internet Service Provider) requires you to use PPPoE for the Internet connection. Click Next to continue and skip to Step 2 on page 33.
Section 4 - Configuration Select Static IP if your Internet Service Provider has provided you with connection settings, or you wish to set a static address within your home network. Click Next to continue. Click Next If you have selected PPPoE, enter your username and password. Click Next to continue.
Section 4 - Configuration If you have a Dynamic DNS account and would like the camera to update your IP address automatically, enable DDNS and enter your host information. Click Next to continue. Click Next Enter a name for your camera and click Next to continue. Click Next Configure the correct time to ensure that all events will be triggered, captured, and scheduled at the right time. Click Next to continue.
Section 4 - Configuration Once you have selected Dynamic, PPPoE, or Static, you will see a summary of your camera’s settings. Click Apply to save and activate your settings.
Section 4 - Configuration Motion Detection Setup Wizard This wizard will guide you through a step-by-step process to configure your new D-Link Camera’s motion detection functions. Click Next to continue. Click Next This section will allow you to enable or disable motion detection as well as control the sensitivity of your camera’s ability to detect movement. Specify the window area, window name, and sensitivity of detection as well as the type of recording (either snapshot of video clip).
Section 4 - Configuration This section will allow you to specify the time and date your camera records motion. Note: Recording camera footage will take up space on your hard drive. Its recommended that you have sufficient disk space for Always function. Click Next This step allows you to specify how you will receive the events notification of your camera, either via using email or FTP. You will need to enter all the relevant information for your email account or FTP settings. Click Next to continue.
Section 4 - Configuration You have completed the Motion Detection Wizard. Click Apply to save your settings.
Section 4 - Configuration Network Setup LAN Settings: Settings for your local area network. DHCP: Select this connection if you have a DHCP server running on your network and would like a dynamic IP address to be assigned to your camera automatically. Static IP Client: You may enter a static or fixed IP address for your camera. IP Address: Enter an IP address. Subnet Mask: The default value is “255.255.255.0.” Used to determine if the destination is in the same subnet.
Section 4 - Configuration Enabling UPnP port forwarding allows the Network Camera to open a secondary HTTP port on the router. You have to add the secondary HTTP port number behind the Network Camera’s public address in order to access the Network Camera from the Internet. For example, when the HTTP port is set to 80 and the secondary HTTP port is set to 8080, refer to the list below for the Network Camera’s IP address. From the Internet In a local area network http://203.67.124.123:8080 http://192.168.
Section 4 - Configuration Secondary HTTP The default value is 8080. Port: After you have enabled the Authentication, you will need to configure and use the access name to access your video file. For example, http://camera ip/video.mjpg (video.mjpg is the Access name, you can modify it here) Access name for The default name is video.mjpg. stream1: Access name for The default name is video2.mjpg.
Section 4 - Configuration The accessibility of the RTSP streaming for the three authentication modes are listed in the following table. Quick Time player Real Player VLC media player mpegable Player pvPlayer Disable O O O O O Basic O O X X X Digest O X X X X O indicates that the authentication mode is supported by the RTSP player. X indicates that the authentication mode is NOT supported by the RTSP player.
Section 4 - Configuration RTSP port: The port number that you use for RSTP streaming, the default port number is 554. RTP (Real Time Protocol) Port is used to streaming audio and video while RTCP (Real Time Control Protocol) port is used to monitor QoS of RTP stream. Note: RTP video port and RTP audio port must be an “even” number. The numbers of RTCP video port and RTCP audio port must equal to the numbers of RTP video port and RTP audio port, plus one repetitively.
Section 4 - Configuration For example, if some content is associated with group 239.1.1.1, the source will send data packets destined to 239.1.1.1. Receivers for that content will inform the network that they are interested in receiving data packets sent to the group 239.1.1.1. The receiver “joins” 239.1.1.1. The Multicast address ranges from 224.0.0.0 to 239.255.255.255, or, equivalently, 224.0.0.0/4 Multicast video port: Default port number is 5560, or please choose between 1024 and 65534.
Section 4 - Configuration Dynamic DNS DDNS (Dynamic Domain Name Server) will hold a DNS host name and synchronize the public IP address of the modem when it has been modified. The username and password are required when using the DDNS service. Enable DDNS: Click to enable the DDNS function. Server Name: Select your Dynamic DNS provider from the drop down menu. Host Name: Enter the host name of the DDNS server.
Section 4 - Configuration Image Setup You may configure the color, brightness, and orientation settings of the video image. Preview of the image will be shown in the window of Live Video. Click Save Settings to save your changes. Color: Select either for Color or B/W (black and white, monochrome) video display. Power line Select either 50 or 60Hz. frequency: Video Flip will vertically rotate the video while Mirror will orientation: horizontally rotate the video.
Section 4 - Configuration Audio and Video Settings for two video streams (stream 1 and stream 2) can be configured here. You may configure one setting for computer display and the other one for mobile display. Mode: Select either JPEG or MPEG4. In JPEG mode, the video frames are independent. However, MPEG4 consumes much less network bandwidth than JPEG. Frame Size: Select 176x144, 352x240, or 640x480. It is recommended using 176x144 for mobile viewing and 640x480 for computer viewing.
Section 4 - Configuration External Select the external microphone input gain from the list. microphone input: Audio type: AAC (Advanced Audio Coding): A wide band audio coding algorithm that exploits two primary coding strategies to dramatically reduce the amount of data needed to convey high-quality digital audio. Select a higher bit rate number for better audio quality. GSM-AMR: A standard adapted audio codec by the 3GPP video (3rd Generation Partnership Project).
Section 4 - Configuration Motion Detection Enabling Motion Detection will allow up to three windows that can be created with different settings for monitoring. This allows your camera to serve as a security device that will record when motion is detected. Enable motion Check this option to turn on the motion detection detection: feature. Window name: Create your own name for the monitored area/ window. It will show at the top of the motion window.
Section 4 - Configuration To enable motion detection, follow the steps below: 1. Click New to add a new motion detection window. 2. Enter a name in the Window Name field. 3. Define the sensitivity to moving objects and the space ratio of all alerted pixels by moving the Sensitivity and Percentage slide bar. 4. Click Save to apply the changes. 5. Select Enable motion detection to activate motion detection. Note: Drag to resize the window and click X to close the window.
Section 4 - Configuration How does motion detection work? A C B D There are two parameters for setting the motion detection: Sensitivity and Percentage. In the illustration above, frame A and frame B are two sequential images. Pixel differences between the two frames are detected and highlighted in gray (frame C), and will be compared with the sensitivity setting. Sensitivity is a value that expresses the sensitivity to moving objects.
Section 4 - Configuration Time and Date Automatically or manually configure, update, and maintain the internal system clock for your camera. Current Server Time: Displays current time. Time Zone: Select your time zone from the drop-down menu. Enable Daylight Select this to enable the daylight saving time Saving: (DST). During DST, the system clock moves one hour ahead. Note: To utilize this feature, ensure to set the time zone of your network camera.
Section 4 - Configuration Event Setup There are four sections in Event Setup page. • Event • Server ������� • Media ����� • Recording ��������� 1. To add a new item - event, server or media click Add. A pop-up will appear and update the fields accordingly. 2. To delete ������������������������������������� the selected item from the pull-down menu of event, server or media click ������ Delete. 3. Click on the item name to pop up a window for modifying.
Section 4 - Configuration Application A typical application is that when motion is detected, the DCS-3110 Network Camera sends images to a FTP server or via e-mail as notifications. For example, as seen in the illustration below, an event can be triggered by many sources, such as motion detection or external digital input devices. When an event is triggered, you can specify what kind of action will be performed.
Section 4 - Configuration Add Server Configure up to 5 servers to store the media. Server Name: Unique name of your server. Email: Select this to enable and apply your email account setting for your camera. FTP: Select this to access a granted folder on the external FTP server. HTTP: Select this to use a web server to store the media. Network Storage: Only one network storage device is supported.
Section 4 - Configuration Add Media There are three types of media, Snapshot, Video Clip and System Log. Media Name: Enter an unique name for media. Snapshot: Select this feature to enable camera to take snapshot. Source: The source of stream: stream1 or stream2. Send pre-event The number of pre-event images. image(s) [0~7]: Send post-event The number of post-event images. Refer page 57 for image(s) [0~7]: more information. File name prefix: The prefix name will be added on the file name.
Section 4 - Configuration Send post-event image (s) [0~7) Specify to capture the number of images after a trigger is activated. A maximum of seven images can be generated. For example: If both the Send pre-event images and Send post-event images are set to seven, a total of 15 images are generated after a trigger is activated. 1 pic. 2 pic. 3 pic. 4 pic. 5 pic. 6 pic. 7 pic. 8 pic. 9 pic. 10 pic. 11 pic. 10 pic. 12 pic. 13 pic. 14 pic. 15 pic. The moment the trigger is activated.
Section 4 - Configuration Maximum duration Specify the maximal recording duration in seconds. You can set up to ten seconds. For example: If the Pre-event recording is set to five seconds and the Maximum duration is set to ten seconds, the Network Camera continues to record for another four seconds after a trigger is activated. 1 sec. 2 sec. 3 sec. 4 sec. 5 sec. 6 sec. 7 sec. 8 sec. 9 sec. 10 sec. The moment the trigger is activated.
Section 4 - Configuration Add Event Create and schedule up to 3 events with their own settings here. Event name: Enter a name for the event. Enable this Select to activate this event. event: Priority: Set the priority for this event. The event with higher priority will be executed first. Delay: Select the delay time before checking next event. It is being used for both events of motion detection and digital input trigger. Trigger: The input type that triggers the event.
Section 4 - Configuration Add Recording Here you can configure and schedule the recording settings. Recording entry The unique name of the entry. name: Enable this Select this to enable the recording function. recording: Priority: Set the priority for this entry. The entry with a higher priority value will be executed first. Source: The source of stream. Recording Scheduling the recording entry. schedule: Recording Configuring the setting for the recording.
Section 4 - Configuration Advanced DI and DO The I/O connector provides the physical interface for digital output (DO) and digital input (DI) that is used for connecting such external alarm devices as IR-Sensors and alarm relays to the network camera. DI and DO: Settings for both Digital input signal and digital output signal can be configured here. Digital input Please select High or Low for digital input trigger trigger condition: condition.
Section 4 - Configuration RS485 With digital PTZ (Pan/Tilt/Zoom) feature enabled, it is possible to zoom in and out video recieved from the DCS-3110. Enable PTZ Operation To utilize this feature, please connect the DCS-3110 to a PTZ scanner via RS485 interface and follow the instructions given below. Three PTZ drivers are supported: • DynaDome/SmartDOME • Lilin PIH-7x00 • Pelco D protocol Note: If none of the above PTZ drivers is supported by your PTZ scanner, please select Custom camera. 1.
Section 4 - Configuration Custom Command Click Custom Command to open the Custom Command page. In this page, you can set addition command buttons for controlling the PTZ scanner. A total of five command buttons can be configured. To add a new control button, follow the steps below. 1. In the Button name text box, enter the descriptive name for the control button. 2. Refer to the PTZ scanner and enter the command. 3. Click Save to take effect and click Close to quit this page. 4.
Section 4 - Configuration ICR ICR - IR-Cut Removable(ICR) filter is a switch mechanical design of two different sensor filters. It provides the best light conditions both during the day and night. The following options are: Auto: The Network Camera automatically switches between day and night mode by judging the level of ambient light. This mode is accessible only when the exposure mode is set to Auto.
Section 4 - Configuration Access List The Access List page will allow you to configure access permissions for each user. Allow list: The list of IP addresses that have the access right to the camera. Start IP address: The starting IP Address of the devices (such as a computer) that have permission to access the video of the camera. Click Add to save the changes made. Note: A total of ten lists can be configured for both columns.
Section 4 - Configuration Maintenance Device Management You can modify both the camera’s name and the administrator’s password, as well as add more user accounts for accessing the camera. Admin password Modify the password for the administrator’s setup: account. Add user account: Add a new user account. Username: Enter a username for the new account. Password: Enter a password for the new account. Privilege: Select the access rights for the new user. Manage user: Manage the accounts for existing users.
Section 4 - Configuration Backup and Restore The Backup and Restore page will allow you to turn the front panel LED off, restore factory default settings, and reboot the camera. Turn off the LED Select this option to turn off the LED next to the indicator: lens. This will prevent anyone from observing the operation of the network camera. Restore: Click the Restore button to reset the camera back to its factory default settings. This will remove all the configuration settings that were made previously.
Section 4 - Configuration Firmware Update Your current firmware version and date will be displayed on your screen. You may go to the D-Link Support page to check for the latest firmware version available. To upgrade the firmware on your DCS-3110, please download and save the latest firmware version from the D-Link support site to your local hard drive. Locate the file on your local hard drive by clicking the Browse button. Then, open the file and click the “Upload” button to start the firmware upgrade.
Section 4 - Configuration Status Device Info This page displays all the details information about your device and network connection.
Section 4 - Configuration Logs This page displays the log information of your camera. You can configure a remote log server so that you can view your log details remotely. Enable remote log: Click to enable this feature so that the camera can send camera log files to a remote server. Log server settings: Configure the settings for the log server. IP Address: The IP address of the remote server. Port: The port number of the remote log server. The default port is 514. Save: Click to save the settings.
Section 4 - Configuration Help D-Link DCS-3110 User Manual 71
Section 4 - D-ViewCam Installation D-ViewCam Installation D-ViewCam software is included for the administrator to manage up to 32 D-Link network cameras remotely. The administrator can use the software to configure the advanced settings for the camera. D-ViewCam is a complete management tool and includes all configurative settings. Insert the CD into the CD-ROM drive. A menu screen will appear as shown below.
Section 4 - D-ViewCam Installation Click Next to continue. Click Next Click Browse if you would like to choose a specific folder for the installation, otherwise click Next to continue.
Section 4 - D-ViewCam Installation Click Next to start the installation. Note: The D-ViewCam installation process may take several minutes to complete. Click Next Click Finish to complete the installation.
Section 4 - D-ViewCam Installation Add a Camera This section will show you how to start and add a camera to the D-ViewCam system. To start D-ViewCam, select Start > All Programs > D-Link > D-Link D-ViewCam. Enter admin as the default username and leave the password blank. Click to log into the system and access the Add Camera Wizard. Note: Please refer to page 48 in the D-ViewCam user manual to change your password.
Section 4 - D-ViewCam Installation Welcome to the Add Camera Wizard. Use this wizard to add your cameras to the D-ViewCam system. Note: Use the left or right arrow to navigate the wizard. Click to continue.
Section 4 - D-ViewCam Installation Select which method to add your camera(s). You can select Auto Discovery to automatically search for your camera(s), or select Add Manually to add your camera(s) using the camera’s IP address. Click Next to continue. If you select Auto Discovery, the system will search all cameras that are located on the same LAN with same subnet. The system will place all the cameras at the default map called My Map. Click Next to continue.
Section 4 - D-ViewCam Installation D-ViewCam shows the detected network camera(s) information. You can select the recording mode for each camera. • 24/7 Continuous Recording: ��������������������������������������������������� Continuously records 24 hours a day, 7 days a week. • 24/7 Motion Detection Recording: ���������������������������������������������������������������� Continuously monitors, but only records when motion is detected.
Section 4 - D-ViewCam Installation Select Yes to add other cameras, or select No if you have no additional cameras to add. Click Next to continue. The Add Camera wizard is now complete. Click Close to access the D-ViewCam’s main screen. Your D-ViewCam Installation is Complete! Note: Please refer to the D-ViewCam user manual for information about using D-ViewCam.
Section 5 - Frequently Asked Questions Frequently Asked Questions This chapter provides solutions to problems that may occur during the installation and operation of the DCS-3110. Read the following descriptions if you are having any problems. Megapixel PoE Network Camera Features 1. What is a Megapixel PoE Network Camera? The Megapixel PoE Network Camera is a stand-alone system connecting directly to an Ethernet or Fast Ethernet network.
Section 5 - Frequently Asked Questions Megapixel PoE Network Camera Installation 1. Can the Network Camera be used outdoors? The Megapixel PoE Network Camera is not weatherproof. It needs to be equipped with a weatherproof case for outdoor use but it is not recommended. 2. When physically connecting the Network Camera to a network, what network cabling is required? The Megapixel PoE Network Camera uses Category 5 UTP cable allowing 10 Base-T and 100 Base-T networking solutions. 3.
Section 5 - Frequently Asked Questions 8. I connected the Network Camera directly to a computer with a cross-over Ethernet cable and received a Windows error upon running the installation Wizard? • • This Windows error will occur if the Megapixel PoE Network Camera is connected to a computer that is not properly configured with a valid IP address. Turn off DHCP from the Network Settings in Windows and configure the computer with a valid IP address or connect the camera to a router with DHCP enabled.
Appendix A - Networking Basics Networking Basics Check your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. (Windows Vista® users type cmd in the Start Search box.) At the prompt, type ipconfig and press Enter.
Appendix A - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/access point, or you need to assign a static IP address, please follow the steps below: Step 1 Windows Vista® - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections. ® Windows XP - Click on Start > Control Panel > Network Connections.
Appendix B - Reset and Restore Reset and Restore There is a button hidden in the pinhole beside the Ethernet socket. It is used to reset the system or restore the factory default settings. Sometimes resetting the DCS-3110 will return the system back to a normal state. If the system still has problems after reset, restore the factory settings and install again: RESET: 1.
Appendix B - External I/O Port External I/O Port DI/DO Diagram Pin 1~4 are used to connect with digital input and digital output devices. Refer to the following illustration for connection method. 12V PIN 1 DO+ Power+12V The DCS-3110 provides a general I/O terminal block with one digital input and one relay switch for device control. The ���������������������������� relay switch of DO+ and DO- can be used to turn on or off the external device.
Appendix C - Technical Specifications Technical Specifications Network Protocol Support SENSOR & LENS SPECIFICATIONS • IPv4, TCP/IP, RTSP/ RTP/ RTCP, HTTP, SMTP, FTP, NTP, DNS, DHCP, UPnP, DDNS,PPPoE, IGMP, Samba client, IP Filtering, 3GPP • • • • Built-in Network Interfaces 1/4” 1.3mega-pixel progressive color CMOS sensor 6 mm megapixel lens, F1.6 Removable IR-cut filter: Auto/Schedule/Manual Minimum illumination: 1.5 Lux, F2.
Appendix C - Technical Specifications SYSTEM REQUIREMENTS • Operating System: Microsoft Windows® XP/Vista • Browser: Internet Explorer, Firefox, Netscape, Mozilla, Opera browser POWER CONSUMPTION • Max 4 W DIMENSIONS • 80 (W) X 143.8 (D) X 62 (H) (mm) SUPPORTED PDA, MOBILE PHONES & SOFTWARE Handsets with 3GPP player • Packet Video Player 3.0 • QuickTime 6.5 • Real Player 10.5 WEIGHT • 521 gm OPERATION TEMPERATURE • 0º to 40º C (32º to 104º F) PHYSICAL & ENVIRONMENTAL LAN • • • • • IEEE 802.
