1 Plug the supplied Ethernet cable from your router or gateway into the port marked 'LAN'. Plug the power adapter into the hub. Make sure the power button is pressed down into the 'ON' position.
2 SYNC Once the hub has powered up, press the SYNC button on each camera to power them on.
3 Scan the QR code above to download the mydlink app for your Android or iOS device.
4 New Users: Tap Sign Up to register for a mydlink account, then tap Add a Device to install your camera. Continue to follow the onscreen inscructions. OR Existing Users: Sign in using your mydlink account and tap the icon at the top-left, then tap Add a Device to start the setup wizard. Continue to follow the onscreen instructions.
5 When prompted, select "Yes" to scan the QR code on the back of the hub, then continue to follow the onscreen instructions to complete the setup process. Note: Please ensure that your mobile device is connected to the Wi-Fi network of the router that you connected the hub to.
Camera Placement Precautions Caution: Please make sure that the camera is not directly facing the sun or a source of heat. Proper Placement: Place the camera at least 2.2 m (7 ft) or higher from the ground. The minimum recommended viewing distance for the motion detection is 60 cm (24 in), and the maximum is 7.5 m (25 ft). 64° 60 cm (24 in) min 115° 2.2 m (7 ft) good detection poor detection 7.
Camera Mounting Instructions Snap Mount Step 1: Identify and mark the location where you want to install the bracket, assuring that it is at least 20 cm from the ceiling. Step 2: Using a 6 mm drill bit, drill a 25 mm deep hole over the mark. For a plaster, drywall, or concrete wall, insert the plastic anchor to support the screw first. Step 3: Twist the supplied screw into the wall or anchor, making sure to leave enough clearance between the screw head and the wall.
Camera Mounting Instructions Threaded Mount Step 1: Place the mount at the desired location, assuring that it is at least 20 cm from the ceiling. Use a pencil to mark the holes. 1 Step 2: Using a 6 mm drill bit, drill two 25 mm deep holes over the pencil marks. For a plaster, drywall, or concrete wall, insert the plastic anchors to support the screws first. 2 Step 3: Place the mount over the holes that are in the wall. Make sure to align the mount holes with the holes in the wall.
Camera LED Information DCS-2800LH Status LED Color Behavior Green Orange Red Solid Motion detected Fully charged Malfunction Solid for 10 sec. Pairing complete N/A Pairing failed / Unpaired Blinking every 1 sec. Currently pairing Charging Updating firmware Blinking every 30 sec.
? Frequently Asked Questions 1) What can I do if my camera is not working properly or I’m having problems setting it up? Reset the hub by pressing the Reset button for 10 seconds using a paper clip, assuring that all the LEDs turn off briefly after releasing the button. Then try setting it up again in the mydlink app. In addition, please verify that: • your Internet connection is active on your router. • your router’s Wi-Fi is turned on. • the camera’s battery has enough power.
Minimum Requirements To install this product, you will need: • An 802.11 g/n wireless router • An Internet connection • The latest version of the mydlink app from the App Store or Google Play. Please refer to the app's store page to check whether your device is compatible.
Support For toubleshooting tips and more information, visit: support.dlink.com Technical Support Australia: Tel: 1300-700-100 24/7 Technical Support Web: http://www.dlink.com.au E-mail: support@dlink.com.au New Zealand: Tel: 0800-900-900 24/7 Technical Support Web: http://www.dlink.co.nz E-mail: support@dlink.co.nz Version 1.00 (AU)_90x130 2018/09/28 Copyright ©2018 All rights reserved. D-Link and the D-Link logo are registered trademarks of D-Link Corporation or its subsidiaries.
Wire-Free Camera Kit Quick Start Guide DCS-2802KT
