Version 1.
Table of Contents Table of Contents Package Contents.......................................................................... 4 System Requirements.................................................................. 5 Introduction.................................................................................... 6 Features............................................................................................. 8 Hardware Overview......................................................................
Table of Contents Help..................................................................................................57 Wireless Security..............................................................58 What is WEP?.................................................................................59 Configure WEP..............................................................................60 What is WPA?.................................................................................
Section 1 - Product Overview Package Contents DAP-3310 Wireless N Exterior Access Point Power Over Ethernet Injector Power Adapter Wall Mount Quick Installation Guide Note: Using a power supply with a different voltage rating or PoE injector than the one included with the DAP-3310 will cause damage and void the warranty for this product.
Section 1 - Product Overview System Requirements Network Requirements • An Ethernet-based Network • IEEE 802.11n/g wireless clients (AP Mode) • IEEE 802.11n/g wireless network (AP Mode) Computer with the following: • Windows®, Macintosh, or Linux-based operating system • An installed Ethernet adapter Web-based Configuration Utility Requirements Browser Requirements: • Internet Explorer® 7 and higher • Mozilla Firefox 12.0 and higher • Google™ Chrome 20.
Section 1 - Product Overview Introduction D-Link, an industry leader in networking, introduces the new D-Link DAP-3310 Wireless N Exterior Access Point. With the ability to transfer files with a maximum wireless signal rate of up to 300 Mbps1, the DAP-3310 gives you ability to add high-speed wireless network access to places outside of your internal networking environment. Additional operation modes such as WDS and WISP also make the DAP-3310 perfect for those needing to span longer distances wirelessly.
Section 1 - Product Overview Ultimate Performance The D-Link Wireless N Exterior Access Point (DAP-3310) is an 802.11n compliant device that delivers real world performance of up to 300 Mbps2, much faster than an 802.11g wireless connection (also faster than a 100 Mbps wired Ethernet connection). Create a secure wireless network to share photos, files, music, video, printers, and network storage outside of your normal internal networking environment.
Section 1 - Product Overview Features • Faster Wireless Networking - The DAP-3310 provides an up to 300 Mbps* wireless connection with other 802.11n wireless clients. This capability allows users to participate in real-time activities online, such as video streaming, online gaming, and real-time audio. • Compatible with IEEE802.11g Devices - The DAP-3310 is still fully compatible with the 802.11g standards, so it can connect with existing 802.11g adapters.
Section 1 - Product Overview Hardware Overview Connections 1 2 3 1 LAN Port 2 LAN (PoE) Port 3 Reset Button 4 4 Connects to 10/100 Ethernet devices such as computers, switches, and hubs. Power is supplied through the LAN cable connected in this port via the Power over Ethernet Injector. Please see “Installation” on page 11 for more details on how to correctly power the DAP-3310 and connect to other networking devices.
Section 1 - Product Overview Hardware Overview LEDs 1 2 3 1 4 Wi r e l e s s S i g n a l Shows different signal strength levels. Strength LED (Only supported in Wireless Client, Repeater, WDS, and WISP mode) 2 Power LED 3 LAN LED 4 LAN LED (PoE) D-Link DAP-3310 User Manual A solid green light indicates the device is powered and ready. A solid green light indicates the LAN port connection is OK. A blinking green light indicates that the unit is transmitting data over that port.
Section 2 - Installation Installation First, you will need to configure the DAP-3310 with a computer connected directly to the unit. The following pages explains how to set up the DAP-3310 in order to be properly configured and then tested to work as desired. The DAP-3310 acts as a central connection point for any device (client) that has a 802.11n or backward-compatible 802.11g wireless network interface and is within range of the AP.
Section 2 - Installation STEP 2: Connect the AP to Your Network AP PoE Injector A P+DATA OUT C Power B DATA IN A. Connect the Ethernet cable (connected to the AP in STEP 1) from the AP to the “P+DATA OUT” port on the PoE Injector. B. Connect an Ethernet cable from a router/switch or PC to the “DATA IN” port on the PoE Injector. C. Attach the power adapter to the connector labeled “POWER IN” on the PoE Injector, and attach it into an electrical outlet.
Section 2 - Installation Wireless Installation Considerations The D-Link Wireless N Exterior Access Point lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range.
Section 3 - Configuration Configuration This section will show you how to configure your new D-Link Wireless N Exterior Access Point using the web-based configuration utility. Web-based Configuration Utility If you wish to change the default settings or optimise the performance of the DAP-3310, you may use the web-based configuration utility. To access the configuration utility, open a web browser such as Internet Explorer and enter http://192.168.0.50 Select admin and then enter your password.
Section 3 - Configuration Operating Modes The DAP-3310 features seven different operating modes, allowing it to adapt to any situation. Select the operating mode by clicking on the radio button, that correspondes to the desired mode then click on Change Mode. After confirming that the operating mode will be changed, the AP will reboot and will be ready for use after 40 seconds. Access Point: In access point (AP) mode, 802.11n/g/b compliant devices can connect to the wireless network.
Section 3 - Configuration Basic Settings The image to the right shows a configuration menu tree for when the AP is in Access Point mode. If you need help determining which operating mode the AP is currently in, please see “Operating Modes” on page 15. Note: The DAP-3310 has different configuration options depending on the current operating mode. Please be aware that some screens and menus will not be present unless the AP is operating in an applicable operating mode.
Section 3 - Configuration Wireless Settings This page will allow you to configure the wireless connection for the DAP-3310. Please be aware that some menu options will change depending on which type of security setting is used. Network Name Enter a name for your wireless network (SSID). For (SSID): security purposes, it is highly recommended to change from the default network name. SSID Visibility: Select Disabled if you do not want the SSID of your wireless network to be broadcasted by the DAP-3310.
Section 3 - Configuration Open System/Shared Key Authentication If you selected Open System as your Authentication, you will see these settings: Encryption: Use the radio button to disable or enable encryption. (Encryption option only available with Open System setting) Key Type: Select either HEX or ASCII as the key type. Key Size: Select 64 Bits or 128 Bits for your key size. Key Index: Select which key you want to be the active key. Network Key: Input up to four keys for encryption.
Section 3 - Configuration WPA/WPA2-Personal Authentication If you selected WPA/WPA2-Personal Authentication as your Authentication, you will see these settings: WPA Mode: Wh e n WPA-Personal i s s e l e c te d fo r Authentication type, you must also select a WPA mode from the drop-down menu: AUTO (WPA or WPA2), WPA2 Only, or WPA Only. WPA and WPA2 use different algorithms. AUTO (WPA or WPA2) allows you to use both WPA and WPA2.
Section 3 - Configuration WPA/WPA2-Enterprise Authentication WPA Mode: When WPA-Enterprise is selected, you must also select a WPA mode from the drop-down menu: AUTO (WPA or WPA2), WPA2 Only, or WPA Only. WPA and WPA2 use different algorithms. AUTO (WPA or WPA2) allows you to use both WPA and WPA2. Cipher Type: When WPA-Enterprise is selected, you must also select a cipher type from the drop-down menu: Auto, AES, or TKIP. Group Key Select the interval during which the group key Update will be valid.
Section 3 - Configuration 802.1x Authentication Key Size: Select 64 Bits or 128 Bits for your key size. RADIUS Server: Enter the IP address of your RADIUS server. RADIUS Port: Enter the RADIUS port. RADIUS Secret: Enter the RADIUS secret.
Section 3 - Configuration Wireless LAN Settings This page will allow you to change the wireless LAN settings of the AP. This function is used when there are multiple access points that are connected to increase wireless coverage over an area. Repeater Set this to the SSID of the wireless network that Network Name: the DAP-3310 will be connecting to.
Section 3 - Configuration LAN Settings This section will allow you to change the local network settings of the DAP-3310. After making your changes, click the Save button. Get IP From: Select an option to choose how the AP will obtain an IP address to use on the local network. If this is set to Static, you will need to manually enter the necessary information. IP Address: Enter the IP address of the router. The default IP address is 192.168.0.50.
Section 3 - Configuration Advanced Settings Performance This options on this page will allow you to fine tune the wireless connectivity of the access point. Wireless: Use the drop-down menu to turn the wireless function On or Off. Wireless Mode: The different combination of clients that can be supported include Mixed 802.11n, 802.11g and 802.11b, Mixed 802.11g and 802.11b and 802.11n Only. Note: When backwards compatibility is enabled for legacy (802.11g/b) clients, degradation of 802.
Section 3 - Configuration DTIM Interval Set a Delivery Traffic Indication Message setting between 1 and 255. The default value is 1. DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages. Transmit This setting determines the power level of Power: the wireless transmission. Transmitting power can be adjusted to eliminate overlapping of wireless area coverage between two access points where interference is a major concern.
Section 3 - Configuration Short GI: Select Enable or Disable. Enabling a short guard interval can increase throughput. However, be aware that it can also increase the error rate in some installations due to increased sensitivity to radio-frequency installations. IGMP Select Enable or Disable. Internet Group Snooping: Management Protocol allows the AP to recognize IGMP queries and reports sent between routers and an IGMP host (wireless STA).
Section 3 - Configuration User Limit: Set the maximum amount of users that are allowed access (1-64 users). To use this feature, the Connection Limit above must be enabled. For most networks, a limit of 10 is recommended. The default setting is 20. Client Isolation: If this option is enabled, connected clients will not be able to view or access each other.
Section 3 - Configuration Multi-SSID The device supports up to four multiple Service Set Identifiers. In the Basic > Wireless section, you can set the Primary SSID. The SSID’s factory default setting is dlink. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network. Network Service Set Identifier (SSID) is the name Name(SSID): designated for a specific wireless local area network (WLAN). SSID Visibility: Enable or Disable SSID visibility.
Section 3 - Configuration VLAN The VLAN List tab displays the current VLANs. Clicking on Create VLAN will allow you to create a new Virtual LAN with a Name and ID. The LAN ports and the Multi-SSID function can be assigned to a VLAN. VLAN Status: Use the radio button to toggle between Enable or Disable. After changing the option, you will need to click on Save to add or edit VLANs. To remove or modify a VLAN, click on the Delete or Edit button. To add a VLAN, click on the Create VLAN button.
Section 3 - Configuration Add/Edit VLAN The VLAN Setup tab is used to configure VLANs. Once you have made the desired changes, click the Save button to let your changes take effect. VLAN ID: Provide a number between 1 and 4094 for the Internal VLAN. VLAN Name: Enter the VLAN to add or modify. LAN Port: Select a LAN port to bind to the SSID. Multi-SSID Select the corresponding SSID to bind to the Port: LAN port in order to create a VLAN.
Section 3 - Configuration WMM This page will allow you to change the settings that control the WMM feature, which provides QoS for any devices that are connected via wireless to the AP. WMM: Select whether to Enable or Disable the WMM functionality of the access point. AC Type: A different type of data is associated with each queue. The queue and associated priorities and parameters for transmission are as follows: (Best Effort, BE): Medium priority queue, medium throughput and delay.
Section 3 - Configuration CWmin: The value specified for the Minimum Contention Window is the lower limit of a range for the initial random backoff wait time. Setting this value gives the DAP-3310 a starting point before beginning to double the window size when a collision is detected. CWMax: The value specified in the Maximum Contention Window is the upper limit for this doubling of the random backoff.
Section 3 - Configuration QoS Quality of Service (QoS) enhances the experience of using a network by prioritizing the traffic of different applications. A QoS Rule identifies a specific type of traffic and will adjust the amount of bandwidth used based on the settings defined here. Service: Enable this option if you want to allow QoS to prioritize your traffic. Mode: Select whether QoS should be based on total bandwidth or on a per rule basis. Upload: Set the QoS limit for upload bandwidth.
Section 3 - Configuration DHCP Server Dynamic Pool Settings The DHCP address pool defines the range of the IP address that can be assigned to stations in the network. A Dynamic Pool allows wireless stations to receive an available IP with lease time control. If needed or required in the network, the DAP-3310 is capable of acting as a DHCP server. Function Select Enable to allow the DAP-3310 to Enable/ function as a DHCP server.
Section 3 - Configuration WINS: Specify the Windows Internet Naming Service (WINS) server address for the wireless network. WINS is a system that determines the IP address of a network computer that has a dynamically assigned IP address. Domain: Enter the domain name of the network, if applicable. (An example of a domain name is: www.dlink.com.) Least Time The lease time is the period of time before the DHCP server will assign new IP addresses.
Section 3 - Configuration Static Pool Settings The DHCP address pool defines the range of IP addresses that can be assigned to stations on the network. A static pool allows specific wireless stations to receive a fixed IP without time control. Computer Enter a name for the computer or device that Name: will be used to identify the IP address and assigned MAC address. Assigned IP: Use the Static Pool Settings to assign the same IP address to a device every time you start up.
Section 3 - Configuration Current IP List This window displays information about the current assigned DHCP dynamic and static IP address pools. This information is available when you enable DHCP server on the AP and assign dynamic and static IP address pools. Assigned IP The current corresponding DHCP-assigned IP Address: address of the device. Binding MAC The MAC address of a device on the network Address: that is assigned an IP address from the DHCP dynamic pool.
Section 3 - Configuration Filter The Access Control filter section can be used to filter network access by machines based on the unique MAC addresses of their network adapter(s). It is most useful to prevent unauthorized wireless devices from connecting to your network. A MAC address is a unique ID assigned by the manufacturer of the network adapter. Access Control When Disabled is selected, MAC addresses List: are not used to control network access.
Section 3 - Configuration Schedule This page will allow you to setup access schedules for the device. This will enable or disable clients from connecting to the device during specified times. Wireless Enable or Disable wireless access based on Schedule: a predetermined schedule by selecting an option from the drop down box. Wireless: Select whether the schedule will either turn the wireless network on, or off.
Section 3 - Configuration If you create a new rule or edit an existing one, you will see these settings: Name: Enter a name to identify the rule being created. Day(s): All Week, or choose Select Day(s) to specify what days the rule should be active on. Day of Week: Select the days that the rule will be active. All Day(s): Select this checkbox if the rule should be active all day for the days specified. Start From: This should be set to the time when the rule will become active.
Section 3 - Configuration DMZ DMZ is short for Demilitarized Zone. If an application has trouble working from behind the router, you can expose a computer to the Internet and run the application on that computer. Service: You can select either Single DMZ or Multiple DMZ. This will allow you to choose whether to expose a single IP address via DMZ, or to expose multiple IP addresses. Note: Placing a computer in the DMZ may expose that computer to a variety of security risks.
Section 3 - Configuration Virtual Server This will allow you to open a single port. This allows a computer or device to provide external access to services or applications that are otherwise blocked by the built-in firewall. To create a virtual server, click on Create New Virtual Server, and the following settings will appear: Service: Select to either Disable or Enable the rule. Description: Enter a name for the rule.
Section 3 - Configuration Parental Control Parental Control is used to allow you to set up a range of IP Addresses that can be either be blacklisted or whitelisted to certain MAC addresses on the network. Active: Select to either Disable or Enable the Parental Control feature. Comment: You can enter a comment here for each rule that is created. MAC Address: Enter the MAC address to be monitored and click Save to add it to the parental control list.
Section 3 - Configuration IP Routing Static Routing Setup This page will allow you to configure the built-in routing protocols that the DAP-3310 allows when in certain operating modes. OSPF Service Select to either Disable or Enable the AP from offering OSPF service. RouterID: Select the interface that the AP will broadcast OSPF from. This should be the main interface that will connect to the local network.
Section 3 - Configuration This page will allow you to define specific routes that will be broadcasted by the AP and made available to the clients that connect to it. Mode: Select whether the route being offered is either Disabled or Enabled. Destination Enter either the destination network, or the Net/Mask: subnet mask that will be used in the static route. Via: Select whether the static route will be controlled by an existing gateway, or if the interface on the AP should route the traffic.
Section 3 - Configuration Maintenance Administration Settings This page will allow you to change a number of settings that are used by the device administrator such as changing the password used to access the device, as well as the method of accessing the device remotely and from what IP address the device can be remotely managed from. Limit Check this to limit administrator access to Administrator specific IP ranges only.
Section 3 - Configuration Enable HTTP: Select this checkbox to enable access to the console via HTTP. The port which the console will use for connections can also be specified. Enable HTTPS: Select this checkbox to enable access to the console via HTTPS. The port which the console will use for connections can also be specified. Enable Telnet: Select this checkbox to enable access to the console via Telnet. The port which the console will use for connections can also be specified.
Section 3 - Configuration SNMP v3: Check the box to enable the SNMP v3 functions. This option is disabled by default. SNMP ro user: Enter the username for read only SNMP access. SNMP ro Enter the password for read only SNMP access. password: SNMP rw user: Enter the username for read/write SNMP access. SNMP rw Enter the password for read/write SNMP access. password: SNMP Trap: Check the box to enable the sending of Trap Status messages.
Section 3 - Configuration Firmware and SSL Certification Upload This page allows you to upgrade the firmware of the access point as well as upload an SSL certificate to secure the connections made to the DAP-3310. Make sure the firmware or SSL certificate you want to use is on the local hard drive of the computer. Please check the D-Link support website for firmware updates by visiting http://support.dlink.com.
Section 3 - Configuration Configuration File This page will allow you to upload or download a configuration file for the DAP-3310. Upload File: Use this option to load a previously saved configuration. Click Browse to find a previously saved configuration file. Then, click the Upload Settings button to transfer those settings to the access point.
Section 3 - Configuration Ping Watchdog This page will allow you to configure the Ping Watchdog function of the AP. Ping Watchdog works by sending ICMP “echo request” packets to a target host and listens for ICMP echo response replies. Ping Watchdog is enabled by default. Ping Select whether the ping watchdog function is Watchdog: Disabled or Enabled. IP Address to Enter the IP address that will be used for the Ping: AP to ping.
Section 3 - Configuration Time and Date The Time Server Setup page allows you to configure, update, and maintain the correct time on the internal system clock. In this section you can set the time zone that you are in. Daylight Saving can also be configured to automatically adjust the time when needed. Enable NTP NTP is short for Network Time Protocol. Server: This allows the system clock to be updated automatically by using an NTP server.
Section 3 - Configuration PoE PassThrough This page will allow you to change the PoE pass through setting of the AP. If this is enabled, the LAN port will allow D-Link surveillance cameras such as the DCS-3716, DCS-6113, and DCS-7110 to be powered through the secondary LAN port. Mode: Select whether the PoE pass through function is Disabled or Enabled.
Section 3 - Configuration Status Device Information This page displays the current LAN, wireless LAN and important device information for the DAP-3310. Firmware Displays the access point’s time and firmware Version: version. Also displays the current operating mode and hardware address (MAC), which may be needed by a network administrator.
Section 3 - Configuration Client Information This window displays the wireless client information for clients currently connected to the DAP-3310. MAC Address: Displays the MAC address of the client. RSSI: Displays the client’s signal strength (received signal strength indicator). TX/RX Rate: Displays the current wireless speed that the client is connected with.
Section 3 - Configuration Ethernet Information The DAP-3310 keeps statistics of the traffic that passes through it. You can view the amount of packets that pass through the LAN and wireless portions of the network. The traffic counter will reset if the access point is rebooted.
Section 3 - Configuration WLAN Information This window displays wireless network statistics for data throughput, transmitted and received frames, and frame errors. The traffic counter will reset if the access point is rebooted.
Section 3 - Configuration Configuration Save and Active When making changes on most of the configuration screens it is best to use the Save button at the bottom of each screen to save (not activate) your configuration changes. You may change settings to multiple pages before activating. Once you are finished, click the Configuration button located at the top of the page and then click Save and Activate. You can then click Activate here to enable your changes.
Section 3 - Configuration Discard Changes When making changes on most of the configuration screens it is best to use the Save button at the bottom of each screen to save (not activate) your configuration changes. If you wish to discard all of the changes you have made, and not yet activated, you may click the Discard button.
Section 3 - Configuration System This page will allow you to restart the AP, or restore its settings to the factory defaults. Click the Restart button to reboot the device. Click the Restore button to reset all settings back to the factory defaults. Please note that this will erase all settings and changes made to the device’s configuration.
Section 3 - Configuration Help Further information and in depth help can be found anytime from the AP’s online help function. Scroll down the Help page for topics and explanations.
Section 4 - Security Wireless Security This section will show you the different levels of security you can use to protect your data from intruders.
Section 4 - Security What is WEP? WEP, or Wired Equivalent Privacy, is a Wi-Fi security protocol that encrypts transmitted data. WEP is an older protocol that is not believed to be as effective anymore. WEP uses a passphrase or key to authenticate your wireless connection. For 64-Bit WEP, the key is an alpha-numeric password that is 10 hex digits or an ASCII password consisting of 5 text characters. The hex digits are either numbers from 0 to 9 or letters from A to F.
Section 4 - Security Configure WEP It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the access point (dlinkap. local). Click on Setup and then click Wireless Setup on the left side. 2.
Section 4 - Security What is WPA? WPA, or Wi-Fi Protected Access, is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy). The 2 major improvements over WEP: • Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a hashing algorithm and, by adding an integrity-checking feature, ensures that the keys haven’t been tampered with. WPA2 is based on 802.
Section 4 - Security Configure WPA/WPA2 Personal It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the access point (dlinkap. local). Click on Setup and then click Wireless Setup on the left side. 2.
Section 4 - Security Configure WPA/WPA2 Enterprise It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the access point (dlinkap. local). Click on Setup and then click Wireless Setup on the left side. 2.
Section 5 - Connecting to a Wireless Network Connect to a Wireless Network Using Windows® XP Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.
Section 5 - Connecting to a Wireless Network Configure WPA-PSK It is recommended to enable WEP on your wireless bridge or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WEP key being used. 1. Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks. 2.
Section 5 - Connecting to a Wireless Network 3. The Wireless Network Connection box will appear. Enter the WPA-PSK passphrase and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The WPA-PSK passphrase must be exactly the same as on the wireless access point.
Section 5 - Connecting to a Wireless Network Using Windows Vista® Windows Vista® users may use the convenient, built-in wireless utility. Follow these instructions: From the Start menu, go to Control Panel, and then click on Network and Sharing Center. The utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) under Select a network to connect to and then click the Connect button.
Section 5 - Connecting to a Wireless Network Click Connect Anyway to continue. The utility will display the following window to indicate a connection is being made. The final window indicates the establishment of a successful connection. The next two pages display the windows used to connect to either a WEP or a WPA-PSK wireless network.
Section 5 - Connecting to a Wireless Network Configure WPA-PSK It is recommended to enable WEP on your wireless bridge or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WEP key being used. Click on a network (displayed using the SSID) using WPA-PSK under Select a network to connect to and then click the Connect button. Enter the appropriate security key or passphrase in the field provided and then click the Connect button.
Section 5 - Connecting to a Wireless Network Using Windows® 7 It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Click on the wireless icon in your system tray (lower-right corner). Wireless Icon 2. The utility will display any available wireless networks in your area.
Section 5 - Connecting to a Wireless Network 3. Highlight the wireless network (SSID) you would like to connect to and click the Connect button. If you get a good signal but cannot access the Internet, check your TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. 4. The following window appears while your computer tries to connect to the router.
Section 5 - Connecting to a Wireless Network 5. Enter the same security key or passphrase that is on your router and click Connect. You can also connect by pushing the WPS button on the router. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
Section 6 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DAP-3310. Read the following descriptions if you are having problems. (The examples below are illustrated in Windows® XP. If you have a different operating system, the screenshots on your computer will look similar to the following examples.) 1.
Section 6 - Troubleshooting • Configure your Internet settings: • Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. • Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. • Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
Section 6 - Troubleshooting 3. Why can’t I connect to certain sites or send and receive emails when connecting through my access point? If you are having a problem sending or receiving email, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc). Note: AOL DSL+ users must use MTU of 1400. To find the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to.
Section 6 - Troubleshooting You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480). Once you find your MTU, you can now configure your access point with the proper MTU size.
Appendix A - Wireless Basics Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers.
Appendix A - Wireless Basics What is Wireless? Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or office. D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford.
Appendix A - Wireless Basics Wireless Personal Area Network (WPAN) Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away. Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries.
Appendix A - Wireless Basics Where is wireless used? Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and it’s becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called “hotspots”.
Appendix A - Wireless Basics Security Don’t let your next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or WEP security feature on the access point. Refer to product manual for detail information on how to set it up. Wireless Modes There are basically two modes of networking: • Infrastructure – All wireless clients will connect to an access point or wireless bridge.
Appendix B - Networking Basics Networking Basics Check your IP address After you install your adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. (Windows® 7/Vista® users type cmd in the Start Search box.) At the prompt, type ipconfig and press Enter.
Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Step 1 Windows® 7 - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Change Adapter Setting. Windows Vista® - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections.
Appendix C - Technical Specifications Technical Specifications Standards • IEEE 802.11n/g/b • IEEE 802.3 • IEEE 802.3u Network Management •Web Browser Interface • HTTP - Secure HTTP (HTTPS) •SNMP v1, v2c, and v3 Security • WPA-Personal & Enterprise • WPA2-Personal & Enterprise • WEP 64/128 bit Encryption • 802.1X Wireless Frequencyt • 2.4 GHz to 2.
