Table of Contents Table of Contents Product Overview......................................................... 4 Package Contents.................................................... 4 System Requirements.............................................. 4 Introduction............................................................... 5 Features.................................................................... 7 Wireless Basics............................................................
Table of Contents Wireless MAC ACL........................................ 51 WLAN Partition.............................................. 52 Status .................................................................... 53 Device Information............................................ 53 Client Information.............................................. 54 WDS Information.............................................. 55 Stats.................................................................. 56 Ethernet........
Section 1 - Product Overview Product PackageOverview Contents D-Link DAP-2310 AirPremier® N Access Point Power Adapter CAT5 Ethernet Cable CD-ROM with User Manual Install Guide Note: Using a power supply with a different voltage rating than the one included with the DAP-2310 will cause damage and void the warranty for this product.
Section 1 - Product Overview Introduction The DAP-2310 802.11n AP increases productivity by allowing you to work faster and more efficiently. With the DAP-2310, bandwidth-intensive applications like graphics or multimedia will benefit significantly because large files are now able to move across the network quickly. The DAP-2310 is capable of operating in one of four different wireless networking modes: Access Point, WDS (Wireless Distribution System) with AP, WDS, or Wireless Client mode.
Section 1 - Product Overview EAP (Extensible Authentication Protocol) is available through the Windows® XP operating system. You will need to use the same type of EAP protocol on all devices in your network when using the 802.1X feature. *Maximum wireless signal rate derived from IEEE Standard 802.11n and 802.11g specifications. Actual data throughput may vary.
Section 1 - Product Overview Features • Four different operation modes - Capable of operating in one of four different operation modes to meet your wireless networking needs: Access Point, WDS with AP, WDS, or Wireless Client. • Faster wireless networking with the 802.11n standard to provide a maximum wireless signal rate of up to 300 Mbps*. • Compatible with the 802.11b standard to provide a wireless data rate of up to 11Mbps, allowing you to migrate your system to the 802.11n and 802.
Section 2 - Installation Wireless Basics D-Link wireless products are based on industry standards to provide high-speed wireless connectivity that is easy to use within your home, business or public access wireless networks. D-Link wireless products provides you with access to the data you want, whenever and wherever you want it. Enjoy the freedom that wireless networking can bring to you.
Section 2 - Installation Standards-Based Technology The DAP-2310 Wireless Access Point utilizes the 802.11b, 802.11g, and 802.11n standards. The IEEE 802.11n standard is an extension of the 802.11b and 802.11g standards that came before it. It increases the maximum wireless signal rate up to 300Mbps* within the 2.4GHz bands, utilizing OFDM technology.
Section 2 - Installation Wireless Installation Considerations The D-Link AirPremier® N wireless access point lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range.
Section 2 - Installation Hardware Overview LEDs 3 1 2 1 Power LED This light will be solid green when the unit is powered on. 2 WLAN LED This light will be flickering green when the 2.4GHz frequency is in use. 3 LAN LED D-Link DAP-2310 User Manual This light will be flickering green when there is active LAN traffic.
Section 2 - Installation Hardware Overview Connections 1 D-Link DAP-2310 User Manual 1 LAN Port 2 Reset 3 Power Receptor 2 3 Connects the DAP-2310 to a switch or PC. Reset the Access Point. Receptor for Power Adapter.
Section 2 - Installation Four Operational Modes Access Point (AP) Create a wireless LAN WDS with AP Wirelessly connect multiple networks while still functioning as a wireless AP WDS Wirelessly connect multiple networks Wireless Client AP acts as a wireless network adapter for your Ethernetenabled device D-Link DAP-2310 User Manual 13
Section 2 - Installation Getting Started Desktop Laptop DAP-2310 LAN RESET 5V 2A 1 Switch 2 1. Connect the power adapter to the receptor on the rear panel of the DAP-2310 and then plug the other end of the power adapter to a wall outlet or power strip. The power LED will turn ON to indicate proper operation. 2. Using an Ethernet cable, insert one end of the cable to the LAN port on the rear panel of the DAP-2310 and the other end of the cable to a switch or router’s LAN port .
Section 3 - Configuration Configuration To configure the DAP-2310, use a computer that is connected to the DAP-2310 with an Ethernet cable (see the Network Layout diagram). Launch your web browser. Type the IP address of the DAP-2310 in the address field (http://192.168.0.50) and press Enter. Make sure that the IP addresses of the DAP-2310 and your computer are in the same subnet. Note: If you have changed the default IP address assigned to the DAP-2310, make sure to enter the correct IP address.
Section 3 - Configuration After successfully logging into the DAP-2310, the following screen will appear: Save and Activate Settings When making changes on most of the configuration screens in this section, use the screen to save (not activate) your configuration changes. button at the bottom of each You may change settings to multiple pages before activating. Once you are finished, click the Configuration button located at the top of the page and then click Save and Activate.
Section 3 - Configuration Basic Settings Wireless Access Point mode Wireless Band: Select 2.4GHz from the drop-down menu. Mode: Select Access Point from the drop-down menu. The other three choices are WDS with AP, WDS, and Wireless Client. Network Name Service Set Identifier (SSID) is the name designated (SSID): for a specific wireless local area network (WLAN). The SSID’s factory default setting is dlink.
Section 3 - Configuration Channel Width: Allows you to select the channel width you would like to operate in. Select 20 MHz if you are not using any 802.11n wireless clients. Auto 20/40 MHz allows you to connect to both 802.11n and 802.11b/g wireless devices on your network. Authentication: Use the drop-down menu to choose Open System, Shared Key, WPA-Personal, WPA-Enterprise, or 802.11x. Select Open System to communicate the key across the network.
Section 3 - Configuration WDS with AP mode In WDS with AP mode, the DAP-2310 wirelessly connects multiple networks while still functioning as a wireless AP. Wireless Band: Select 2.4GHz from the drop-down menu. Mode: WDS with AP mode is selected from the drop-down menu. Network Name Service Set Identifier (SSID) is the name designated for (SSID): a specific wireless local area network (WLAN). The SSID’s factory default setting is dlink.
Section 3 - Configuration Remote AP MAC Enter the MAC addresses of the APs on your network that will serve as bridges to wirelessly connect multiple networks. Address: Site Survey: Click on the Scan button to search for available wireless networks, then click on the available network that you want to connect with. Authentication: Use the drop-down menu to choose Open System, Shared Key, or WPA-Personal. Select Open System to communicate the key across the network.
Section 3 - Configuration WDS mode In WDS mode, the DAP-2310 wirelessly connects multiple networks, without functioning as a wireless AP. Wireless Band: Select 2.4GHz from the drop-down menu. Mode: WDS is selected from the drop-down menu. Network Name Service Set Identifier (SSID) is the name designated (SSID): for a specific wireless local area network (WLAN). The SSID’s factory default setting is dlink.
Section 3 - Configuration Site Survey: Click on the Scan button to search for available wireless networks, then click on the available network that you want to connect with. Authentication: Use the drop-down menu to choose Open System, Shared Key, or WPA-Personal. Select Open System to communicate the key across the network. Select Shared Key to limit communication to only those devices that share the same WEP settings. Select WPA-Personal to secure your network using a password and dynamic key changes.
Section 3 - Configuration Wireless Client mode Wireless Band: Select 2.4GHz from the drop-down menu. Mode: Network Name (SSID): Wireless Client is selected from the drop-down menu. Service Set Identifier (SSID) is the name designated for a specific wireless local area network (WLAN). The SSID’s factory default setting is dlink. The SSID can be easily changed to connect to an existing wireless network. SSID Visibility: This option is unavailable in Wireless Client mode.
Section 3 - Configuration Enable: Check to enable clone MAC. This feature will allow you to change the MAC address of the access point to the MAC address of a client. MAC Source: Select the MAC source from the drop-down menu. MAC Address: Enter the MAC address that you would like to assign to the access point.
Section 3 - Configuration Open System/Shared Key Authentication Encryption: Use the radio button to disable or enable encryption. Key Type*: Select HEX or ASCII. Key Size: Select 64 Bits or 128 Bits. Key Index (1-4): Select the 1st through the 4th key to be the active key. Key: Input up to four keys for encryption. You will select one of these keys in the Key Index drop-down menu. **Hexadecimal (HEX) digits consist of the numbers 0-9 and the letters A-F.
Section 3 - Configuration WPA/WPA2-Personal Authentication WPA Mode: When WPA-Personal is selected for Authentication type, you must also select a WPA mode from the drop-down menu: AUTO (WPA or WPA2), WPA2 Only, or WPA Only. WPA and WPA2 use different algorithms. AUTO (WPA or WPA2) allows you to use both WPA and WPA2. Cipher Type: When you select WPA-Personal, you must also select AUTO, AES, or TKIP from the drop-down menu. Group Key Select the interval during which the group key will be Update: valid.
Section 3 - Configuration WPA/WPA2-Enterprise Authentication WPA Mode: When WPA-Enterprise is selected, you must also select a WPA mode from the drop-down menu: AUTO (WPA or WPA2), WPA2 Only, or WPA Only. WPA and WPA2 use different algorithms. AUTO (WPA or WPA2) allows you to use both WPA and WPA2. Cipher Type: When WPA-Enterprise is selected, you must also select a cipher type from the drop-down menu: Auto, AES, or TKIP. Group Key Select the interval during which the group key will Update be valid.
Section 3 - Configuration 802.1x Authentication Key Update Interval: Select the interval during which the group key will be valid (300 is the recommended value). A lower interval may reduce data transfer rates. RADIUS Server: Enter the IP address of the RADIUS server. RADIUS Port: Enter the RADIUS port. RADIUS Secret: Enter the RADIUS secret.
Section 3 - Configuration LAN LAN is short for Local Area Network. This is considered your internal network. These are the IP settings of the LAN interface for the DAP-2310. These settings may be referred to as private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet. Get IP From: Static IP (Manual) is chosen here.
Section 3 - Configuration Advanced Settings Performance Wireless: Use the drop-down menu to turn the wireless function On or Off. Wireless Mode: The different combination of clients that can be supported include Mixed 802.11n, 802.11g and 802.11b, Mixed 802.11g and 802.11b and 802.11n Only. Please note that when backwards compatibility is enabled for legacy (802.11g/b) clients, degradation of 802.11n wireless performance is expected.
Section 3 - Configuration Beacon Interval (25- Beacons are packets sent by an access point to synchronize a wireless network. Specify a value in milliseconds. The default (100) 500): is recommended. Setting a higher beacon interval can help to save the power of wireless clients, while setting a lower one can help a wireless client connect to an access point faster. DTM Interval Select a Delivery Traffic Indication Message setting between 1 and 15. The default value is 1.
Section 3 - Configuration Multi-SSID The device supports up to four multiple Service Set Identifiers. In the Basic > Wireless section, you can set the Primary SSID. The SSID’s factory default setting is dlink. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network. Enable Multi-SSID: Check to enable support for multiple SSIDs. Band: This read-only value is the current band setting. Index: You can select up to three multi-SSIDs.
Section 3 - Configuration Priority: WMM (Wi-Fi Multimedia): Encryption: Key Type: Key Size: Key Index (1-4): Key: WPA Mode: Cipher Type: Group Key Update Interval: Check the Enable Priority box at the top of this window to enable. Select the priority from the drop-down menu. Select Enable or Disable. When you select Open System, toggle between Enable and Disable. If Enable is selected, the Key Type, Key Size, Key Index (1~4), Key, and Confirm Keys must also be configured. Select HEX or ASCII.
Section 3 - Configuration VLAN VLAN List The DAP-2310 supports VLANs. VLANs can be created with a Name and VID. Mgmt (TCP stack), LAN, Primary Multiple SSID, and WDS connection can be assigned to VLANs as they are physical ports. Any packet which enters the DAP-2310 without a VLAN tag will have a VLAN tag inserted with a PVID. The VLAN List tab displays the current VLANs. VLAN Status: Use the radio button to toggle between Enable or Disable.
Section 3 - Configuration Port List The Port List tab displays the current ports. If you want to configure the guest and internal networks on a Virtual LAN (VLAN), the switch and DHCP server you are using must also support VLANs. As a prerequisite step, configure a port on the switch for handling VLAN tagged packets as described in the IEEE 802.1Q standard. VLAN Status: Use the radio button to toggle to Enable. Next, go to the Add/Edit VLAN tab to add or modify an item on the VLAN List tab.
Section 3 - Configuration Add/Edit VLAN The Add/Edit VLAN tab is used to configure VLANs. Once you have made the desired changes, click the Save button to let your changes take effect. VLAN Status: VLAN ID: VLAN Name: Use the radio button to toggle to Enable. Provide a number between 1 and 4094 for the Internal VLAN. Enter the VLAN to add or modify.
Section 3 - Configuration PVID Setting The PVID Setting tab is used to enable/disable the Port VLAN Identifier Auto Assign Status as well as to configure various types of PVID settings. Click the Save button to let your changes take effect. VLAN Status: Use the radio button to toggle between Enable and Disable. PVID Auto Assign Status: Use the radio button to toggle PVID auto assign status to Enable.
Section 3 - Configuration Intrusion The Wireless Intrusion Protection window is used to set APs as All, Valid, Neighborhood, Rogue, and New. Click the Save button to let your changes take effect. AP List: The choices include All, Valid, Neighbor, Rogue, and New. Detect: Click this button to initiate a scan of the network.
Section 3 - Configuration Schedule The Wireless Schedule Settings window is used to add and modify scheduling rules on the device. Click the Save button to let your changes take effect. Wireless Schedule: Use the drop-down menu to enable the device’s scheduling feature. Name: Enter a name for the new scheduling rule in the field provided. Index: Select the index from the drop-down menu. SSID: Enter the name of your wireless network (SSID).
Section 3 - Configuration QoS Quality of Service (QoS) enhances the experience of using a network by prioritizing the traffic of different applications. A QoS Rule identifies a specific message flow and assigns a priority to that flow. For most applications, the priority classifiers ensure the right priorities and specific QoS Rules are not required. QoS supports overlaps between rules. If more than one rule matches a specific message flow, the rule with the highest priority will be used.
Section 3 - Configuration Name: Priority: Protocol: Host 1 IP Range: Host 1 Port Range: Host 2 IP Range: Host 2 Port Range: Enter a name for the new QoS rule in the field provided. Use the drop-down menu to select the desired priority: Background (BK), Best Effort (BE), Video (VI), or Voice (VO). Use the drop-down menu to choose the appropriate protocol used by the messages: Any, TCP, UDP, Both, IMCP, or Other.
Section 3 - Configuration AP Array An AP array is a set of devices on a network that are organized into a single group to increase ease of management. Enable Array: AP Array Name: This check box allows the user to enable the AP array function. The three modes that are available are Master, Backup Master, and Slave. APs in the same array will use the same configuration.
Section 3 - Configuration Wireless Basic Settings Network Name (SSID): Select this option to use a Network Name (SSID). SSID Visibility: Select this option to enable SSID Visibility. Auto Channel Selection: Select this option to use Auto Channel Selection. Channel Width: Security: Select this option to specify the Channel Width. Select this option to use Wireless Security.
Section 3 - Configuration Multiple SSID & VLAN SSID: Select this option to use an SSID. SSID Visibility: Select this option to make the SSID Visible. Security: Select this option to use Wireless Security. WMM: Select this option to use WMM. VLAN: Select this option to use VLAN. Advanced Functions Schedule Settings: Select this option to use Scheduled Settings. QoS Settings: Select this option to use Quality of Service. DHCP Server Settings: Select this option to use DHCP.
Section 3 - Configuration ARP Spoofing Prevention The ARP Spoofing Prevention feature allows users to add IP/MAC address mapping to prevent ARP spoofing attack. ARP Spoofing Prevention: Gateway IP Address: Gateway MAC Address: This check box allows you to enable the ARP spoofing prevention function. Enter a gateway IP address. Enter a gateway MAC address.
Section 3 - Configuration DHCP Server Dynamic Pool Settings The DHCP address pool defines the range of the IP address that can be assigned to stations in the network. A Dynamic Pool allows wireless stations to receive an available IP with lease time control. If needed or required in the network, the DAP-2310 is capable of acting as a DHCP server. Function Enable/Disable: Dynamic Host Configuration Protocol (DHCP) assigns dynamic IP addresses to devices on the network.
Section 3 - Configuration DNS: Domain Name: Lease Time (60-31536000 sec): Enter the IP address of the Domain Name System (DNS) server. The DNS server translates domain names such as www.dlink.com into IP addresses. Enter the domain name of the network, if applicable. (An example of a domain name is: www.dlink.com.) The lease time is the period of time before the DHCP server will assign new IP addresses.
Section 3 - Configuration Static Pool Setting The DHCP address pool defines the range of IP addresses that can be assigned to stations on the network. A static pool allows specific wireless stations to receive a fixed IP without time control. Function Enable/Disable: Dynamic Host Configuration Protocol (DHCP) assigns IP addresses to wireless devices on the network.
Section 3 - Configuration Gateway: Specify the Gateway address for the wireless network. WINS: Specify the Windows Internet Naming Service (WINS) server address for the wireless network. WINS is a system that determines the IP address of a network computer with a dynamically assigned IP address, if applicable. DNS: Enter the Domain Name System (DNS) server address for the wireless network. The DNS server translates domain names such as www.dlink.com into IP addresses.
Section 3 - Configuration Current IP Mapping List This window displays information about the current assigned DHCP dynamic and static IP address pools. This information is available when you enable DHCP server on the AP and assign dynamic and static IP address pools. Current DHCP These are IP address pools the DHCP server has Dynamic assigned using the dynamic pool setting. Profile: Host Name: The host name of a device on the network that is assigned an IP address from the DHCP dynamic pool.
Section 3 - Configuration Filters Wireless MAC ACL Wireless Band: Displays the current wireless band rate. Access Control List: Select Disable to disable the filters function. Select Accept to accept only those devices with MAC addresses in the Access Control List. All other devices not on the list will be rejected. Select Reject to reject the devices with MAC addresses on the Access Control List. All other devices not on the list will be accepted.
Section 3 - Configuration WLAN Partition Wireless Band: Displays the current wireless band rate. Link Integrity: Select Enable or Disable. Ethernet to WLAN Access: The default is Enable. When disabled, all data from the Ethernet to associated wireless devices will be blocked. Wireless devices can still send data to the Ethernet. Internal Station Connection: The default value is Enable, which allows stations to inter-communicate by connecting to a target AP.
Section 3 - Configuration Status Device Information Device This read-only window displays the configuration Information: settings of the DAP-2310, including the firmware version and the device's MAC address.
Section 3 - Configuration Client Information Client Information: This window displays the wireless client information for clients currently connected to the DAP-2310. The following information is available for each client communicating with the DAP-2310. SSID: Displays the SSID of the client. MAC: Displays the MAC address of the client. Band: Displays the wireless band that the client is connected to. Authentication: Displays the type of authentication being used.
Section 3 - Configuration WDS Information WDS Information: This window displays the Wireless Distribution System information for clients currently connected to the DAP-2310. The following information is available for each client communicating with the DAP-2310. Name: MAC: Authentication: Displays the SSID of the client. Displays the MAC address of the client. Displays the type of authentication being used. Signal: Displays the client's signal strength.
Section 3 - Configuration Stats Ethernet Ethernet Traffic Statistics: This page displays transmitted and received count statistics for packets and bytes.
Section 3 - Configuration WLAN Traffic WLAN Traffic Statistics: This page displays wireless network statistics for data throughput, transmitted and received frames, and frame errors.
Section 3 - Configuration Log View Log View Log: The AP’s embedded memory displays system and network messages including a time stamp and message type. The log information includes but is not limited to the following items: cold start AP, upgrading firmware, client associate and disassociate with AP, and web login. The web page holds up to 500 logs.
Section 3 - Configuration Log Settings Log Server/IP Address: Enter the IP address of the server you would like to send the DAP-2310 log to. Log Type: Check the box for the type of activity you want to log. There are three types: System Activity, Wireless Activity, and Notice. Email Notification: Outgoing Mail Server (SMTP): Authentication: SSL / TLS: From Email Address: To Email Address: Email Server Address: Check to enable Email notification. Select the SMTP server from the drop-down menu.
Section 3 - Configuration Maintenance Administration Settings Check one or more of the five main categories to display the various hidden administrator parameters and settings displayed on the next five pages.
Section 3 - Configuration Limit Administrator Each of the five main categories display various hidden administrator parameters and settings. Limit Administrator VLAN ID: Check the box provided and the enter the specific VLAN ID that the administrator will be allowed to log in from. Limit Administrator IP: Check to enable the Limit Administrator IP address. IP Range: Enter the IP address range that the administrator will be allowed to log in from and then click the Add button.
Section 3 - Configuration System Name Settings Each of the five main categories display various hidden administrator parameters and settings. System Name: The name of the device. The default name is D-Link DAP-2310. Location: The physical location of the device, e.g. 72nd Floor, D-Link HQ.
Section 3 - Configuration Login Settings Each of the five main categories display various hidden administrator parameters and settings. Login Name: Enter a user name. The default is admin. Old Password: When changing your password, enter the old password here. New Password: When changing your password, enter the new password here. The password is case-sensitive. “A” is a different character than “a.” The length should be between 0 and 12 characters.
Section 3 - Configuration Console Settings Each of the five main categories display various hidden administrator parameters and settings. Status: Status is enabled by default. Uncheck the box to disable the console. Console Protocol: Select the type of protocol you would like to use, Telnet or SSH. Timeout: Set to 1 Min, 3 Mins, 5 Mins, 10 Mins, 15 Mins or Never.
Section 3 - Configuration SNMP Settings Each of the five main categories display various hidden administrator parameters and settings. Status: Check the box to enable the SNMP functions. This option is disabled by default. Public Community String: Enter the public SNMP community string. Private Community String: Enter the private SNMP community string. Trap Status: Check the box to enable Trap Status. Trap Server IP: Enter the Trap Server IP address.
Section 3 - Configuration Firmware and SSL Certification Upload This page allows the user to perform a firmware upgrade. A Firmware upgrade is a function that upgrade the running software used by the access point. This is a useful feature that prevents future bugs and allows for new features to be added to this product. Please go to your local D-Link website to see if there is a newer version firmware available. Upload The current firmware version is displayed Firmware From above the file location field.
Section 3 - Configuration Configuration File Upload Upload File: Click the Browse button to locate a previously saved configuration file on your local computer. After selecting the file, click Upload to apply the configuration settings to the DAP-2310. Download Configuration File: Click Download to save the current DAP-2310 configuration to your local computer.
Section 3 - Configuration Time and Date Current Time: Displays the current time and date settings. Time Zone: Use the drop-down menu to select your correct Time Zone. Enable Daylight Saving: Check the box to Enable Daylight Saving Time. Daylight Saving Dates: Use the drop-down menu to select the correct Daylight Saving offset. Enable NTP Server: Check to enable the AP to get system time from an NTP server. NTP Server: Enter the NTP server IP address.
Section 3 - Configuration System System Settings Restart the Device: Click Restart to restart the DAP-2310. Restore to Factory Default Settings: Click Restore to restore the DAP-2310 back to factory default settings. Clear Language Pack: Click Clear to remove any loaded language packs.
Section 3 - Configuration Help Help: Scroll down the Help page for topics and explanations.
Section 6 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DAP-2310. Read the following descriptions if you are having problems. (The examples below are illustrated in Windows® XP. If you have a different operating system, the screenshots on your computer will look similar to the following examples.) 1. Why can’t I access the web-based configuration utility? When entering the IP address of the D-Link access point (192.
Section 6 - Troubleshooting If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your router. Some firewall software programs may block a DHCP request on newly installed adapters. • Make sure you have an updated Java-enabled web browser. We recommend the following: - Microsoft Internet Explorer® 6.0 and higher - Mozilla Firefox 3.0 and higher - Google™ Chrome 2.0 and higher - Apple Safari 3.
Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Step 1 Windows® 2000: Click on Start > Settings > Control Panel > Network Connections Windows® XP: Click on Start > Control Panel > Network Connections Windows Vista®: Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage network connections Step 2 Right-click on the Local Area Conne
Appendix B - Networking Basics Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The Secondary DNS is not needed or you may enter a DNS server from your ISP. Step 5 Click OK twice to save your settings.
Appendix B - Networking Basics • Configure your Internet settings: • Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. • Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. • Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
Appendix C - Technical Specifications Technical Specifications Standards • IEEE 802.11b • IEEE 802.11g • IEEE 802.11n • IEEE 802.3 • IEEE 802.3u • IEEE 802.3ab • IEEE 802.3af Network Management • Web Browser interface HTTP Secure HTTP (HTTPS) • AP Manager II • AP Array Tool • SNMP Support D-View Module Private MIB • Command Line Interface Telnet Secure SSH Telnet • 802.1x • WEP™ 64-/128-bit • SSID Broadcast Disable • MAC Address Access Control Wireless Frequency Range • 2.4 to 2.
Appendix E - Warranty LEDs • Power • LAN • 2.
Appendix D - Contacting Technical Support Contacting Technical Support U.S. and Canadian customers can contact D-Link technical support through our web site or by phone. Before you contact technical support, please have the following ready: • Model number of the product (e.g. DAP-2310) • Hardware Revision (located on the label on the bottom of the access point (e.g. rev A1)) • Serial Number (s/n number located on the label on the bottom of the access point).
Appendix E - Warranty Warranty Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty: • Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and • Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.
Appendix E - Warranty Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90) days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation.
Appendix E - Warranty • After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the product and will not ship back any accessories.
Appendix E - Warranty While necessary maintenance or repairs on your Product can be performed by any company, we recommend that you use only an Authorized D-Link Service Office. Improper or incorrectly performed maintenance or repair voids this Limited Warranty.
Appendix E - Warranty derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as stipulated by the United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice. Copyright ©2011 by D-Link Corporation/D-Link Systems, Inc. All rights reserved. CE Mark Warning: This is a Class B product.
Appendix E - Warranty This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Industry Canada Statement This device complies with RSS-210 of the Industry Canada Rules.
Appendix F - Registration Registration Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Version 1.
