User Manual DAP-1155 Wireless N 150 Access Point & Router November 2012
DAP-1155 Wireless N 150 Access Point & Router User Manual Contents Chapter 1. Introduction..........................................6 Contents and Audience.......................................................6 Conventions.................................................................6 Document Structure..........................................................6 Chapter 2. Overview..............................................7 General Information........................................................
DAP-1155 Wireless N 150 Access Point & Router User Manual Wi-Fi......................................................................52 Common settings..........................................................52 Basic Settings...........................................................53 Security Settings........................................................55 MAC Filter...............................................................59 Station List...........................................................
DAP-1155 Wireless N 150 Access Point & Router User Manual Net.......................................................................131 WAN.....................................................................131 Creating PPPoE WAN Connection.........................................132 Creating Static IP WAN Connection.....................................136 Creating Dynamic IP WAN Connection....................................139 Creating PPTP + Static IP or L2TP + Static IP WAN Connection..........
DAP-1155 Wireless N 150 Access Point & Router User Manual Chapter 6. Operation Guidelines................................213 Safety Instructions.......................................................213 Wireless Installation Considerations......................................213 Chapter 7. Abbreviations and Acronyms..........................
DAP-1155 Wireless N 150 Access Point & Router Introduction User Manual CHAPTER 1. INTRODUCTION Contents and Audience This manual describes the access point DAP-1155 and explains how to configure and operate it. This manual is intended for users familiar with basic networking concepts, who create an in-home local area network, and system administrators, who install and configure networks in offices. Conventions Example ! Description text The body text of the manual.
DAP-1155 Wireless N 150 Access Point & Router Overview User Manual CHAPTER 2. OVERVIEW General Information The DAP-1155 device is a wireless access point supporting the router mode. It is an affordable solution for creating wireless networks at home or in an office. Using DAP-1155, you are able to quickly create a wireless network and let your relatives or employees connect to it virtually anywhere (within the operational range of your wireless network).
DAP-1155 Wireless N 150 Access Point & Router Overview User Manual Specifications* WAN Interface: • 1 10/100BASE-TX Ethernet port for cable or DSL modem or private Ethernet line. LAN Interface: • 1 10/100BASE-TX Ethernet port. WLAN Interface: • IEEE 802.11n (up to 150Mbps) • IEEE 802.11b/g. Operation Modes: • Access point mode • Router mode.
DAP-1155 Wireless N 150 Access Point & Router Overview User Manual Wireless Connection: • WLAN splitting (up to 4 SSIDs) • Supported security settings: ◦ WEP ◦ WPA/WPA2 Personal • MAC filter • Managing connected stations • PIN and PBC methods of WPS • WMM (Wi-Fi QoS) • Advanced settings • WDS • “Client” function (access point mode): ◦ Wireless network client ◦ Wireless network repeater • “Client” function (router mode): ◦ WISP repeater.
DAP-1155 Wireless N 150 Access Point & Router Overview User Manual Configuration and Management: • Multilingual web-based interface for configuration and management • Access via TELNET • Firmware update via web-based interface • Saving/restoring configuration to/from file • Support of remote logging • Automatic synchronization of system time with NTP server (router mode) • Ping function • Traceroute utility (router mode). LEDs: • Power • WLAN • WPS • LAN • Internet.
DAP-1155 Wireless N 150 Access Point & Router Overview User Manual Product Appearance Front Panel Figure 1. Front panel view. LED Power WLAN WPS LAN Internet Mode Description Solid green The device is powered on. No light The device is powered off. Solid green The device's WLAN is on. Blinking green The WLAN interface downstream traffic). Solid green The wireless device is connected to the access point's WLAN (lights for several minutes).
DAP-1155 Wireless N 150 Access Point & Router Overview User Manual Back Panel Figure 2. Back panel view. Port Description 12 VDC IN Power connector. INTERNET A port to connect to a cable or DSL modem or to a private Ethernet line (it is recommended to use the cable included in the delivery package). LAN An Ethernet port to connect to a computer. A button to restore the factory default settings and to quickly add wireless devices to the access point's WLAN (the WPS function).
DAP-1155 Wireless N 150 Access Point & Router Overview User Manual Delivery Package The following should be included: • Access point DAP-1155 • Power adapter DC 12V • Ethernet cable (CAT 5E) • “Quick Installation Guide” (brochure). The “User Manual” and “Quick Installation Guide” documents in Russian and English are available on D-Link website (see ftp.dlink.ru/pub/Wireless/DAP-1155/Description/Rev.B/).
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual CHAPTER 3. INSTALLATION AND CONNECTION Before You Begin Please, read this manual prior to installing the device. Make sure that you have all the necessary information and equipment. Operating System Configuration of the access point DAP-1155 supporting the router mode (hereinafter referred to as “the access point”) is performed via the built-in web-based interface.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual Connecting to PC PC with Ethernet Adapter 1. Make sure that your PC is powered off. 2. Connect an Ethernet cable between the LAN port located on the back panel of the access point and the Ethernet port of your PC. 3. Connect the power cord to the power connector port on the back panel of the access point, then plug the power adapter into an electrical outlet or power strip. 4.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual 3. In the Local Area Connection Properties window, on the General tab, select the Internet Protocol (TCP/IP) line. Click the Properties button. Figure 4. The Local Area Connection Properties window.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual 4. Select the Use the following IP address radio button and enter the value 198.168.0.51 in the IP address field. The Subnet mask field will be filled in automatically. Click the OK button. Figure 5. The Internet Protocol (TCP/IP) Properties window. 5. Click the ОК button in the connection properties window. Now you can connect to the web-based interface of DAP-1155 for configuring all needed parameters.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual Configuring IP Address in OS Windows 7 1. Click the Start button and proceed to the Control Panel window. 2. Select the Network and Sharing Center section. (If the Control Panel has the category view (the Category value is selected from the View by drop-down list in the top right corner of the window), choose the View network status and tasks line under the Network and Internet section.) Figure 6.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual 3. In the menu located on the left part of the window, select the Change adapter settings line. Figure 7. The Network and Sharing Center window.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual 4. In the opened window, right-click the relevant Local Area Connection icon and select the Properties line in the menu displayed. Figure 8. The Network Connections window.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual 5. In the Local Area Connection Properties window, on the Networking tab, select the Internet Protocol Version 4 (TCP/IPv4) line. Click the Properties button. Figure 9. The Local Area Connection Properties window.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual 6. Select the Use the following IP address radio button and enter the value 198.168.0.51 in the IP address field. The Subnet mask field will be filled in automatically. Click the OK button. Figure 10. The Internet Protocol Version 4 (TCP/IPv4) Properties window. 7. Click the OK button in the connection properties window. Now you can connect to the web-based interface of DAP-1155 for configuring all needed parameters.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual PC with Wi-Fi Adapter 1. Connect the power cord to the power connector port on the back panel of the access point, then plug the power adapter into an electrical outlet or power strip. 2. Turn on your PC and wait until your operating system is completely loaded. 3. Turn on your Wi-Fi adapter.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual Configuring Wi-Fi Adapter in OS Windows XP 1. Click the Start button and proceed to the Control Panel > Network and Internet Connections > Network Connections window. 2. In the Network Connections window, right-click the relevant Wireless Network Connection icon. Make sure that your Wi-Fi adapter is on, then select the Properties line in the menu displayed. 3.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual 6. Search for available wireless networks. Figure 12. The Network Connections window. 7. In the opened Wireless Network Connection window, select the wireless network DAP1155 and click the Connect button. After that the Wireless Network Connection Status window appears. Now you can connect to the web-based interface of DAP-1155 for configuring all needed parameters.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual Configuring Wi-Fi Adapter in OS Windows 7 1. Click the Start button and proceed to the Control Panel window. 2. Select the Network and Sharing Center section. (If the Control Panel has the category view (the Category value is selected from the View by drop-down list in the top right corner of the window), choose the View network status and tasks line under the Network and Internet section.) Figure 13.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual 6. Select the Use the following IP address radio button and enter the value 198.168.0.51 in the IP address field. The Subnet mask field will be filled in automatically. Click the OK button. Figure 14. The Internet Protocol Version 4 (TCP/IPv4) Properties window. 7. Click the OK button in the connection properties window. 8.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual 9. In the opened window, in the list of available wireless networks, select the wireless network DAP-1155 and click the Connect button. Figure 16. The list of available networks. 10. Wait for about 20-30 seconds. After the connection is established, the network icon will be displayed as the signal level scale. Now you can connect to the web-based interface of DAP-1155 for configuring all needed parameters.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual Connecting to Web-based Interface When you have configured your computer, you can access the web-based interface and configure needed parameters (configure the wireless network, change the operating mode of the device, specify the settings of the firewall, etc.). 1. Start a web browser (see the Before You Begin section, page 14). 2. In the address bar of the web browser, enter http://dlinkap/ or http://192.168.0.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual Right after the first access to the web-based interface you are forwarded to the page for changing the administrator password specified by default. Figure 19. The page for changing the default administrator password. Enter a new password in the Password and Confirmation fields (you may use digits, Latin letters (uppercase and/or lowercase), and characters available on the keyboard), then click the Save link.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual Web-based Interface Structure After successful registration the access point's quick settings page opens. The selected operating mode defines the view of the quick settings page and the components of the web-based interface. The web-based interface of the access point is multilingual. Select a needed language from the menu displayed when the mouse pointer is over the Language caption.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual Also you can find a specific page via search. To do this, enter the name of the page, wholly or partly, in the search bar in the top part of the web-based interface page, and then select a needed link in the search results. Figure 21. The page displaying the search results.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual Access Point Mode The quick settings page displays general information on the access point and its software (the version and the date of the firmware, the IP address of the device, the name of the WLAN, etc.). Figure 22. The quick settings page in the access point mode.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual To configure the access point's WLAN parameters, left-click the SSID of the WLAN (the right column of the SSID line). After clicking the line, the Wi-Fi / Basic settings page opens (for the detailed description of the page, see the Basic Settings section, page 53).
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual The pages of the System section provide functions for managing the internal system of the access point (for the description of the pages, see the System section, page 77). Also you can change the operating mode of the device directly from the advanced settings page. To switch the device to the router mode, select the Router position ( ) of the Switch device mode switch.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual To edit the access point's local interface parameters, left-click the IP or MAC address of the local interface (the right column of the LAN IP line or LAN MAC line correspondingly). After clicking the line, the page for editing the LAN interface opens (for the detailed description of the page, see the LAN section, page 152).
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual The pages of the Wi-Fi section are designed for specifying all needed settings of the access point's wireless network (for the description of the pages, see the Wi-Fi section, page 155). Also you can enable or disable the device's WLAN directly from the advanced settings page. To enable the WLAN, select the On position ( ) of the Enable/Disable Wi-Fi switch.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual Figure 27. The top-page menu. Click the Reboot line if you have already saved the access point's settings. Click the Save&Reboot line to save new settings and immediately reboot the access point. Click the Save line to save new settings to the non-volatile memory and continue configuring the device. Also you can save the device's parameters via the Save button on the System / Configuration page.
DAP-1155 Wireless N 150 Access Point & Router Installation and Connection User Manual Device Operation Modes Access Point Mode In the access point mode, the device is used to create a wireless local area network or to connect to a wired router. Router Mode In the router mode, the device is used to connect to the Internet. You can connect the device to a cable or DSL modem or to a private Ethernet line and create a WAN connection.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual CHAPTER 4. MODE) CONFIGURING DEVICE (ACCESS POINT Wireless Network Settings Wizard To specify all needed settings for your wireless network, click the Wireless network settings wizard link in the Wi-Fi section. Figure 28. Common and advanced settings of the wireless LAN.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual In the Basic settings section, you can change the basic parameters of your access point's WLAN: “hide” your wireless network (Hide Access Point), specify a name for the network (SSID), select your location (Country) and the wireless channel number (Channel), specify the operating mode (Wireless Mode) and the maximum number of devices connected to the wireless network (Max Associated Clients). Figure 29.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual On the next page, you can modify security settings of the WLAN. By default, the Open network authentication type with no encryption is specified for the WLAN. Figure 30. The default security settings. ! The default security settings do not provide sufficient protection for the WLAN. Please, specify your own security settings for the WLAN (or each part of the WLAN if the network was splitted into parts).
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Figure 31. Network authentication types supported by the access point. The access point supports the following authentication types: Authentication type Description Open Open authentication (with WEP encryption for wireless network modes not supporting 802.11n devices). Shared Shared key authentication with WEP encryption.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual When the Open or Shared value is selected, the WEP Encryption settings section is displayed (the section is unavailable for the wireless network operating modes which support the standard 802.11n): Figure 32. The Open value is selected from the Network Authentication drop-down list. Parameter Description The checkbox activating WEP encryption.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual When the WPA-PSK or WPA2-PSK value is selected, the WPA Encryption settings section is displayed: Figure 33. The WPA2-PSK value is selected from the Network Authentication drop-down list. Parameter Description Encryption Key PSK A key for WPA encryption. The key can contain digits and/or Latin characters.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Status The pages of this section display data on the current state of the access point: • network statistics • IP addresses leased by the DHCP server • data on devices connected to the access point's network and its web-based interface. Network Statistics On the Status / Network statistics page, you can view statistics for all connections existing in the system (LAN, WLAN).
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual DHCP The Status / DHCP page displays the information on computers that have been identified by hostnames and MAC addresses and have got IP addresses from the DHCP server of the device, as well as the IP address expiration periods (the lease time). Figure 35. The Status / DHCP page.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual LAN Clients On the Status / LAN clients page, you can view the list of devices connected to the access point and devices accessing its web-based interface. Figure 36. The Status / LAN clients page. For each device the following data are displayed: the IP address, the MAC address, and the interface to which the device is connected.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Net In this menu you can configure basic parameters of the local area network of the access point. LAN To configure the access point's local interface, proceed to the Net / LAN page. Figure 37. Basic settings of the local interface. If needed, edit the basic settings of the local interface. Parameter Description IP Address The IP address of the access point in the local subnet.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Parameter Description An operating mode of the access point's DHCP server. Mode Enable: the access point assigns IP addresses to clients automatically in accordance with the specified parameters. When this value is selected, the DNS Relay, Start IP, End IP, and the Lease time fields are displayed on the page. Disable: the access point's DHCP server is disabled, clients' IP addresses are assigned manually.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Figure 39. The section for creating MAC-IP pairs. To create a MAC-IP pair, click the Add button. In the IP field, enter an IP address which will be assigned to the device from the LAN, then in the MAC field, enter the MAC address of this device. In the Host field, specify a network name of the device for easier identification (optional).
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Wi-Fi In this menu you can specify all needed settings for your wireless network. Common settings On the Wi-Fi / Common settings page, you can enable your wireless local area network (WLAN) and split it into parts. Figure 40. Common settings of the wireless LAN. The Enable Wireless checkbox enables Wi-Fi connections. By default, the checkbox is selected.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Basic Settings On the Wi-Fi / Basic settings page, you can configure basic parameters of the device's WLAN. Figure 41. Basic settings of the wireless LAN.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Parameter Description Hide Access Point If the checkbox is selected, other users cannot see your Wi-Fi network. (It is recommended not to select this checkbox in order to simplify initial configuration of your WLAN.) SSID A name for the WLAN. By default, the value DAP-1155 is specified. If your network is splitted into parts, each part has the default name (DAP-1155.2, DAP-1155.3, and DAP-1155.4).
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Security Settings On the Wi-Fi / Security settings page, you can modify security settings of the WLAN. Figure 42. The default security settings. By default, the Open network authentication type with no encryption is specified for the WLAN. ! The default security settings do not provide sufficient protection for the WLAN.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Figure 43. Network authentication types supported by the access point. The access point supports the following authentication types: Authentication type Description Open Open authentication (with WEP encryption for wireless network modes not supporting 802.11n devices). Shared Shared key authentication with WEP encryption.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual When the Open or Shared value is selected, the WEP Encryption settings section is displayed (the section is unavailable for the wireless network operating modes which support the standard 802.11n): Figure 44. The Open value is selected from the Network Authentication drop-down list. Parameter Description The checkbox activating WEP encryption.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual When the WPA-PSK or WPA2-PSK value is selected, the WPA Encryption settings section is displayed: Figure 45. The WPA2-PSK value is selected from the Network Authentication drop-down list. Parameter Description Encryption Key PSK A key for WPA encryption. The key can contain digits and/or Latin characters.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual MAC Filter On the Wi-Fi / MAC Filter page, you can define a set of MAC addresses of devices which will be allowed to access the WLAN, or define MAC addresses of devices which will not be allowed to access the WLAN. Figure 46. The MAC filter for the wireless network. By default, MAC filtering is not active (the Disabled choice of the MAC filter restrict mode radio button is selected).
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Figure 47. The tab for adding a MAC address. Enter an address in the MAC address field of the MAC address adding section and click the Add button. To remove a MAC address from the list of MAC addresses, select the checkbox located to the right of the relevant MAC address in the MAC address list section and click the Delete button.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Station List On the Wi-Fi / Station List page, you can view the list of wireless clients connected to the access point. Devices connected to the access point via the WDS function are not displayed in the list. Figure 48. The list of the wireless clients.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual WPS On the Wi-Fi / WPS page, you can enable the function for secure configuration of the WLAN and select a method used to easily add wireless devices to the WLAN. The WPS function helps to configure the protected wireless network automatically. Devices connecting to the wireless network via the WPS function must support the WPS function.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual To activate the WPS function, select the WPS Enable checkbox and click the Change button. When the checkbox is selected, the Information and Connection sections are available on the page. Parameter Description Default PIN code The PIN code of the access point. This parameter is used when connecting the access point to a registrar to set the parameters of the WPS function.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Using WPS Function via Web-based Interface To add a wireless device via the PIN method of the WPS function, follow the next steps: 1. Select the WPS Enable checkbox. 2. Click the Change button. 3. Select the PIN value from the WPS Method drop-down list. 4. Select the PIN method in the software of the wireless device that you want to connect to the access point's WLAN. 5.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Later you will be able to add wireless devices to the WLAN by pressing the WPS/RESET button of the access point. 1. Select the PBC method in the software of the wireless device that you want to connect to the access point's WLAN. 2. Click the relevant button in the software or press the WPS button on the cover of the wireless device that you want to connect to the WLAN. 3.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual WDS On the Wi-Fi / WDS page, you can enable the WDS function and select a mode of this function. The WDS function allows joining local area networks together via a wireless connection of access points. Figure 50. The page for configuring the WDS function.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual The following fields are available on the page: Parameter Description The WDS function mode. Disable: The function is disabled. WDS Mode Bridge mode: Access points communicate to each other only, wireless devices cannot connect to them. Repeater mode: Access points communicate to each other, wireless clients can connect to the WLAN created by interconnected access points.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Additional Settings On the Wi-Fi / Additional settings page, you can define additional parameters for the WLAN of the access point. ! Changing parameters presented on this page may negatively affect your WLAN! Figure 51. Additional settings of the WLAN.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Parameter TX Power Description The transmit power (in percentage terms) of the access point. The 802.11b and 802.11g protection function is used to minimize collisions between devices of your wireless network. Select a value from the drop-down list.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual WMM On the Wi-Fi / WMM page, you can enable the Wi-Fi Multimedia function. The WMM function implements the QoS features for Wi-Fi networks. It helps to improve the quality of data transfer over Wi-Fi networks by prioritizing different types of traffic. To enable the function, select the WMM checkbox and click the Change button. Figure 52. The page for configuring the WMM function.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual For every Access Category the following fields are available: Parameter Description Aifsn Arbitrary Inter-Frame Space Number. This parameter influences time delays for the relevant Access Category. The lower the value, the higher is the Access Category priority. CWMin/CWMax Contention Window Minimum/Contention Window Maximum. Both fields influence time delays for the relevant Access Category.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Client On the Wi-Fi / Client page in the access point mode, you can configure the device as a client to connect to a wireless access point. The “client” function in the access point mode allows using DAP-1155 as a wireless client and a wireless repeater.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Figure 54. The page for configuring the client mode. To configure the access point as a client, select the Enable client checkbox. When the checkbox is selected, the following fields are displayed on the page: Parameter SSID Description The name of the network to which the access point connects. BSSID The unique identifier of the network to which the access point connects.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual When the Open or Shared authentication type is selected, the following fields are available: Parameter Description The checkbox activating WEP encryption. When the checkbox is selected, the Default Key ID field and four Encryption Key Enable Encryption WEP WEP fields are displayed on the page. For the Shared authentication type the checkbox is always selected.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Firewall In this menu you can configure the firewall of the access point. MAC Filter On the Firewall / MAC filter page, you can configure MAC-address-based filtering for computers of the access point's LAN. Figure 55. The Firewall / MAC filter page. To specify a new address for the MAC filter, click the Add button.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Figure 56. The page for adding an address for the MAC filter. On the opened page, enter the MAC address of the device from the access point's LAN in the MAC address field. To choose a device connected to the access point's LAN at the moment, select the relevant value from the drop-down list (the field will be filled in automatically).
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual System In this menu you can do the following: • change the password used to access the access point's settings • save the current settings to the non-volatile memory • create a backup of the access point's configuration • restore the access point's configuration from a previously saved file • restore the factory default settings • view the system log • update the firmware of the access point •
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Administrator Password On the System / Administrator password page, you can change the password for the administrator account used to access the web-based interface of the access point and to access the device settings via TELNET. ! For security reasons, it is strongly recommended to change the administrator password upon initial configuration of the access point. Figure 57.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Configuration On the System / Configuration page, you can save the changed settings to the non-volatile memory, restore the factory defaults, backup the current configuration, or restore the device's configuration from a previously created file. Figure 58. The System / Configuration page.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual The following buttons are available on the page: Control Description Save Click the button to save settings to the non-volatile memory. Please, save settings every time you change the device's parameters. Otherwise the changes will be lost upon hardware reboot of the access point. Factory Click the button to restore the factory default settings.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual System Log On the System / System log page, you can set the system log options and configure sending the system log to a remote host. Figure 59. The System / System log page. The Configuration tab. To enable logging of the system events, select the Logging checkbox on the Configuration tab. Then specify the needed parameters. Control Description Select a type of logging from the drop-down list.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Control Description Port A port of the host specified in the Server field. By default, the value 514 is specified. After specifying the needed parameters, click the Change button. To disable logging of the system events, deselect the Logging checkbox and click the Change button. On the Log tab, the events specified in the Logging level list are displayed. Figure 60. The System / System log page.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Firmware Upgrade On the System / Firmware upgrade page, you can upgrade the firmware of the access point. ! Upgrade the firmware only when the access point is connected to your PC via a wired connection. Figure 61. The System / Firmware upgrade page.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual 6. Select the Factory line in the top-page menu displayed when the mouse pointer is over the System caption. 7. Wait until the access point is rebooted. Log into the web-based interface, using the default IP address, login and password (192.168.0.50, admin, admin).
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Ping On the System / Ping page, you can check availability of a host from the local or global network via the Ping utility. The Ping utility sends echo requests to a specified host and receives echo replies. Figure 62. The System / Ping page.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Telnet On the System / Telnet page, you can enable or disable access to the device settings via TELNET from your LAN. By default, access is enabled. Figure 63. The System / Telnet page. To disable access via TELNET, deselect the On checkbox and click the Change button. To enable access via TELNET again, select the On checkbox.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Access Point Mode) User Manual Device mode On the System / Device mode page, you can change the operating mode of the device. Figure 64. The page for changing the operating mode of the device. To switch the device to the other mode, select the Router value from the Work mode drop-down list and click the Change button. In the opened dialog box, click the OK button to save new settings and immediately reboot the access point.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual CHAPTER 5. CONFIGURING DEVICE (ROUTER MODE) Click'n'Connect To configure connection to the Internet, click the Click'n'Connect link in the Net section. Figure 65. Configuring connection to the Internet. Connect the Ethernet cable provided by your ISP to the WAN port of the access point. Verify the relevant LED (the Internet LED should be on). Click the Next button to continue.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 66. The page for selecting the connection type. On the opened page, select the needed choice of the radio button and click the Next button.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Creating WAN Connection PPPoE Connection Figure 67. Configuring PPPoE WAN connection. In the Connection name field, specify a name for the connection for easier identification. In the Username field, enter your login, and in the Password and Password confirmation fields – the password provided by your ISP. As a rule, the specified settings are enough to configure a connection of the selected type.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 68. Configuring PPPoE WAN connection. The expert settings mode. The Ethernet section. Parameter Connection name Description A name for connection for easier identification. Ethernet MTU The maximum size of units transmitted by the interface. A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 69. Configuring PPPoE WAN connection. The expert settings mode. The PPP section. Parameter Description PPP Username Without authorization Password Password confirmation A username (login) to access the Internet. Select the checkbox if you don't need to enter a username and password to access the Internet. A password to access the Internet. The confirmation of the entered password (to avoid mistypes).
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description Dial on demand Select the checkbox if you want the access point to establish connection to the Internet on demand. In the Maximum idle time field, specify a period of inactivity (in seconds) after which the connection should be terminated. PPP IP extension This option is used by some ISPs. Contact your ISP to clarify if this checkbox needs to be enabled.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 70. Configuring PPPoE WAN connection. The expert settings mode. The Miscellaneous section. Parameter Description Miscellaneous Enable RIP Select the checkbox to allow using RIP for this connection. Enable IGMP Multicast Select the checkbox to allow multicast traffic from the external network (e.g. video streaming) to be received.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Static IP Connection Figure 71. Configuring Static IP WAN connection. In the Connection name field, specify a name for the connection for easier identification. Fill in the IP Address and Netmask fields. In the Gateway IP address field, enter the IP address of the gateway used by this WAN connection. In the Primary DNS server field, enter the address of the primary DNS server.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 72. Configuring Static IP WAN connection. The expert settings mode. The Ethernet section. Parameter Connection name Description A name for connection for easier identification. Ethernet MTU The maximum size of units transmitted by the interface. A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 73. Configuring Static IP WAN connection. The expert settings mode. The IP and Miscellaneous sections. Parameter Description IP IP Address Enter an IP address for this WAN connection. Netmask Enter a subnet mask for this WAN connection. Gateway IP address Enter an IP address of the gateway used by this WAN connection.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description Ping Select the checkbox to allow the access point to answer ping requests from the external network through this connection. For security reasons, it is recommended not to select this checkbox. Click the Next button to continue. After that the page displaying all specified settings opens. Click the Apply button to create the connection or the Back button to specify other settings.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Dynamic IP Connection Figure 74. Configuring Dynamic IP WAN connection. In the Connection name field, specify a name for the connection for easier identification. If your ISP has provided the addresses of the DNS servers, deselect the Obtain DNS server addresses automatically checkbox and fill in the Primary DNS server field.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 75. Configuring Dynamic IP WAN connection. The expert settings mode. The Ethernet section. Parameter Connection name Description A name for connection for easier identification. Ethernet MTU The maximum size of units transmitted by the interface. A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 76. Configuring Dynamic IP WAN connection. The expert settings mode. The IP and Miscellaneous sections. Parameter Description IP Obtain DNS server addresses automatically Select the checkbox to configure automatic assignment of DNS server addresses. If the checkbox is selected, the Primary DNS server and Secondary DNS server fields are not displayed.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description Ping Select the checkbox to allow the access point to answer ping requests from the external network through this connection. For security reasons, it is recommended not to select this checkbox. Click the Next button to continue. After that the page displaying all specified settings opens. Click the Apply button to create the connection or the Back button to specify other settings.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual PPTP + Static IP or L2TP + Static IP Connection Figure 77. Configuring PPTP + Static IP WAN connection. Fill in the IP Address and Netmask fields. In the Gateway IP address field, enter the IP address of the gateway used by this WAN connection. In the Primary DNS server field, enter the address of the primary DNS server.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 78. Configuring PPTP + Static IP WAN connection. The expert settings mode. The Ethernet section. Parameter Description Ethernet MTU The maximum size of units transmitted by the interface. A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding. In the field, enter the MAC address registered by your ISP upon concluding the agreement.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 79. Configuring PPTP + Static IP WAN connection. The expert settings mode. The IP and Miscellaneous sections. Parameter Description IP IP Address Enter an IP address for this WAN connection. Netmask Enter a subnet mask for this WAN connection. Gateway IP address Primary DNS server/ Secondary DNS server Enter an IP address of the gateway used by this WAN connection.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description Ping Select the checkbox to allow the access point to answer ping requests from the external network through this connection. For security reasons, it is recommended not to select this checkbox. Click the Next button to continue. If needed, enter the IP addresses of the ISP's local resources. Figure 80. Configuring PPTP + Static IP WAN connection. Click the Next button to continue.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 81. Configuring PPTP + Static IP WAN connection. In the Connection name field, specify a name for the connection for easier identification. In the Username field, enter your login, and in the Password and Password confirmation fields – the password provided by your ISP. In the VPN server address field, enter the IP or URL address of the PPTP or L2TP authentication server.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 82. Configuring PPTP + Static IP WAN connection. The expert settings mode. The VPN section. Parameter Connection name Description A name for connection for easier identification. VPN Connect automatically Username Without authorization Password Password confirmation VPN server address Select the checkbox to enable auto-start of the connection upon the boot-up of the access point.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description Select a method of MPPE encryption. Encryption • No encrypt: MPPE encryption is not applied. • MPPE 40/128 bit: MPPE encryption with a 40-bit or 128-bit key is applied. • MPPE 40 bit: MPPE encryption with a 40-bit key is applied. • MPPE 128 bit: MPPE encryption with a 128-bit key is applied.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 83. Configuring PPTP + Static IP WAN connection. The expert settings mode. The Miscellaneous section. Parameter Description Miscellaneous Enable RIP Select the checkbox to allow using RIP for this connection. NAT Select the checkbox if you want one WAN IP address to be used for all computers of your LAN. Firewall Select the checkbox to enable protection against ARP and DDoS attacks.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual PPTP + Dynamic IP or L2TP + Dynamic IP Connection Figure 84. Configuring PPTP + Dynamic IP WAN connection. If your ISP has provided the addresses of the DNS servers, deselect the Obtain DNS server addresses automatically checkbox and fill in the Primary DNS server field. As a rule, the specified settings are enough to configure a non-protected connection of the selected type.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 85. Configuring PPTP + Dynamic IP WAN connection. The expert settings mode. The Ethernet section. Parameter Description Ethernet MTU The maximum size of units transmitted by the interface. A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding. In the field, enter the MAC address registered by your ISP upon concluding the agreement.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 86. Configuring PPTP + Dynamic IP WAN connection. The expert settings mode. The IP and Miscellaneous sections. Parameter Description IP Obtain DNS server addresses automatically Select the checkbox to configure automatic assignment of DNS server addresses. If the checkbox is selected, the Primary DNS server and Secondary DNS server fields are not displayed.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description Ping Select the checkbox to allow the access point to answer ping requests from the external network through this connection. For security reasons, it is recommended not to select this checkbox. Click the Next button to continue. Figure 87. Configuring PPTP + Dynamic IP WAN connection. In the Connection name field, specify a name for the connection for easier identification.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 88. Configuring PPTP + Dynamic IP WAN connection. The expert settings mode. The VPN section. Parameter Connection name Description A name for connection for easier identification. VPN Connect automatically Username Without authorization Password Password confirmation VPN server address Select the checkbox to enable auto-start of the connection upon the boot-up of the access point.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description Select a method of MPPE encryption. Encryption • No encrypt: MPPE encryption is not applied. • MPPE 40/128 bit: MPPE encryption with a 40-bit or 128-bit key is applied. • MPPE 40 bit: MPPE encryption with a 40-bit key is applied. • MPPE 128 bit: MPPE encryption with a 128-bit key is applied.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 89. Configuring PPTP + Dynamic IP WAN connection. The expert settings mode. The Miscellaneous section. Parameter Description Miscellaneous Enable RIP Select the checkbox to allow using RIP for this connection. NAT Select the checkbox if you want one WAN IP address to be used for all computers of your LAN. Firewall Select the checkbox to enable protection against ARP and DDoS attacks.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Checking Internet Availability On the page, you can check the WAN connection you have created. Figure 90. Checking the Internet availability. In the Result section, the status of the WAN connection and possible causes of malfunctions are displayed. To recheck the status of the WAN connection, enter the IP address or name of a host in the Address field or leave the value specified by default (ya.ru).
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Configuring Wireless Connection On the page, you can change the name of your wireless network, specify a password to it, or disable Wi-Fi connections. Figure 91. Configuring the wireless connection. In the SSID field, specify a new name for the network (use digits and Latin characters). In the Encryption Key PSK field, enter a key (a password that will be used to access your wireless network).
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Wireless Network Settings Wizard To specify all needed settings for your wireless network, click the Wireless network settings wizard link in the Wi-Fi section. Figure 92. Common and advanced settings of the wireless LAN. On the opened page, in the Common settings section, select the Enable Wireless checkbox (if it was deselected before) to enable Wi-Fi connections.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual In the Basic settings section, you can change the basic parameters of your access point's WLAN: “hide” your wireless network (Hide Access Point), specify a name for the network (SSID), select your location (Country) and the wireless channel number (Channel), specify the operating mode (Wireless Mode) and the maximum number of devices connected to the wireless network (Max Associated Clients). Figure 93.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual On the next page, you can modify security settings of the WLAN. By default, the Open network authentication type with no encryption is specified for the WLAN. Figure 94. The default security settings. ! The default security settings do not provide sufficient protection for the WLAN. Please, specify your own security settings for the WLAN (or each part of the WLAN if the network was splitted into parts).
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 95. Network authentication types supported by the access point. The access point supports the following authentication types: Authentication type Description Open Open authentication (with WEP encryption for wireless network modes not supporting 802.11n devices). Shared Shared key authentication with WEP encryption.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual When the Open or Shared value is selected, the WEP Encryption settings section is displayed (the section is unavailable for the wireless network operating modes which support the standard 802.11n): Figure 96. The Open value is selected from the Network Authentication drop-down list. Parameter Description The checkbox activating WEP encryption.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual When the WPA-PSK or WPA2-PSK value is selected, the WPA Encryption settings section is displayed: Figure 97. The WPA2-PSK value is selected from the Network Authentication drop-down list. Parameter Description Encryption Key PSK A key for WPA encryption. The key can contain digits and/or Latin characters.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Virtual Server Settings Wizard To create a virtual server for redirecting incoming Internet traffic to a specified IP address in the LAN, click the Virtual server settings wizard link in the Firewall section. Figure 98. The page for adding a virtual server.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Status The pages of this section display data on the current state of the access point switched to the router mode: • network statistics • IP addresses leased by the DHCP server • the routing table • data on devices connected to the device's network and its web-based interface.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual DHCP The Status / DHCP page displays the information on computers that have been identified by hostnames and MAC addresses and have got IP addresses from the DHCP server of the device, as well as the IP address expiration periods (the lease time). Figure 100. The Status / DHCP page.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Routing Table The Status / Routing table page displays the information on routes. The table contains destination IP addresses, gateways, subnet masks, and other data. Figure 101. The Status / Routing table page.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual LAN Clients On the Status / LAN clients page, you can view the list of devices connected to the access point and devices accessing its web-based interface. Figure 102. The Status / LAN clients page. For each device the following data are displayed: the IP address, the MAC address, and the interface to which the device is connected.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Net In this menu you can configure basic parameters of the local area network of the access point and configure connection to the Internet (a WAN connection). WAN On the Net / WAN page, you can create and edit connections used by the access point. Figure 103. The Net / WAN page. To create a new connection, click the Add button. On the page displayed, specify the relevant values.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Creating PPPoE WAN Connection To create a connection of the PPPoE type, click the Add button on the Net / WAN page. On the opened page, select the PPPoE value from the Connection Type drop-down list and specify the needed values. Figure 104. The page for creating a new connection. The General settings and Ethernet sections.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding. In the field, enter the MAC address registered by your ISP upon concluding the agreement.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description PPP Username Without authorization Password Password confirmation A username (login) to access the Internet. Select the checkbox if you don't need to enter a username and password to access the Internet. A password to access the Internet. The confirmation of the entered password (to avoid mistypes). Service name The name of the PPPoE authentication server.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 106. The page for creating a new connection. The Miscellaneous section. Parameter Description Miscellaneous Enable RIP Select the checkbox to allow using RIP for this connection. Enable IGMP Multicast Select the checkbox to allow multicast traffic from the external network (e.g. video streaming) to be received.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Creating Static IP WAN Connection To create a connection of the Static IP type, click the Add button on the Net / WAN page. On the opened page, select the Static IP value from the Connection Type drop-down list and specify the needed values. Figure 107. The page for creating a new connection. The General settings and Ethernet sections.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding. In the field, enter the MAC address registered by your ISP upon concluding the agreement.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description IP IP Address Enter an IP address for this WAN connection. Netmask Enter a subnet mask for this WAN connection. Gateway IP address Enter an IP address of the gateway used by this WAN connection. Primary DNS server/ Enter addresses of the primary and secondary DNS servers in the Secondary DNS server relevant fields.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Creating Dynamic IP WAN Connection To create a connection of the Dynamic IP type, click the Add button on the Net / WAN page. On the opened page, select the Dynamic IP value from the Connection Type drop-down list and specify the needed values. Figure 109. The page for creating a new connection. The General settings and Ethernet sections.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding. In the field, enter the MAC address registered by your ISP upon concluding the agreement.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description IP Obtain DNS server addresses automatically Select the checkbox to configure automatic assignment of DNS server addresses. If the checkbox is selected, the Primary DNS server and Secondary DNS server fields are not displayed. Primary DNS server/ Enter addresses of the primary and secondary DNS servers in the relevant fields. Secondary DNS server Vendor ID The identifier of your ISP.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Creating PPTP + Static IP or L2TP + Static IP WAN Connection To create a connection of the PPTP + Static IP or L2TP + Static IP type, click the Add button on the Net / WAN page. On the opened page, select the relevant value from the Connection Type dropdown list and specify the needed values. Figure 111. The page for creating a new connection. The General settings and Ethernet sections.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding. In the field, enter the MAC address registered by your ISP upon concluding the agreement.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description Miscellaneous Enable RIP Select the checkbox to allow using RIP for this connection. Enable IGMP Multicast Select the checkbox to allow multicast traffic from the external network (e.g. video streaming) to be received. NAT Select the checkbox if you want one WAN IP address to be used for all computers of your LAN.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description VPN Connect automatically Username Without authorization Password Password confirmation VPN server address Select the checkbox to enable auto-start of the connection upon the boot-up of the access point. A username (login) to access the Internet. Select the checkbox if you don't need to enter a username and password to access the Internet. A password to access the Internet.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description Static IP Address Fill in the field if you want to use a static IP address to access the Internet. PPP debug Select the checkbox if you want to log all data on PPP connection debugging. IP received The IP address assigned by the ISP. Figure 114. The page for creating a new connection. The Miscellaneous section.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Creating PPTP + Dynamic IP or L2TP + Dynamic IP WAN Connection To create a connection of the PPTP + Dynamic IP or L2TP + Dynamic IP type, click the Add button on the Net / WAN page. On the opened page, select the relevant value from the Connection Type drop-down list and specify the needed values. Figure 115. The page for creating a new connection. The General settings and Ethernet sections.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding. In the field, enter the MAC address registered by your ISP upon concluding the agreement.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description Enable IGMP Multicast Select the checkbox to allow multicast traffic from the external network (e.g. video streaming) to be received. NAT Select the checkbox if you want one WAN IP address to be used for all computers of your LAN. Firewall Select the checkbox to enable protection against ARP and DDoS attacks.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description VPN Connect automatically Username Without authorization Password Password confirmation VPN server address Select the checkbox to enable auto-start of the connection upon the boot-up of the access point. A username (login) to access the Internet. Select the checkbox if you don't need to enter a username and password to access the Internet. A password to access the Internet.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description Static IP Address Fill in the field if you want to use a static IP address to access the Internet. PPP debug Select the checkbox if you want to log all data on PPP connection debugging. IP received The IP address assigned by the ISP. Figure 118. The page for creating a new connection. The Miscellaneous section.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual LAN To configure the access point's local interface, proceed to the Net / LAN page. Figure 119. Basic settings of the local interface. If needed, edit the basic settings of the local interface. Parameter Description IP Address The IP address of the access point in the local subnet. By default, the following value is specified: 192.168.0.50. Netmask The mask of the local subnet.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description Select the checkbox so that the devices connected to the access point obtain the address transmitted by the ISP or specified on the Advanced / DNS page as the DNS server address. DNS Relay Deselect the checkbox so that the devices connected to the access point obtain the address of the access point as the DNS server address.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Existing MAC-IP pairs are displayed in the table of the Static DHCP section. To remove a pair, select the checkbox in the relevant line in the table and click the Remove button. Then click the Save button.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Wi-Fi In this menu you can specify all needed settings for your wireless network. Common settings On the Wi-Fi / Common settings page, you can enable your wireless local area network (WLAN) and split it into parts. Figure 122. Common settings of the wireless LAN. The Enable Wireless checkbox enables Wi-Fi connections. By default, the checkbox is selected.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Basic Settings On the Wi-Fi / Basic settings page, you can configure basic parameters of the device's WLAN. Figure 123. Basic settings of the wireless LAN.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description Hide Access Point If the checkbox is selected, other users cannot see your Wi-Fi network. (It is recommended not to select this checkbox in order to simplify initial configuration of your WLAN.) SSID A name for the WLAN. By default, the value DAP-1155 is specified. If your network is splitted into parts, each part has the default name (DAP-1155.2, DAP-1155.3, and DAP-1155.4).
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Security Settings On the Wi-Fi / Security settings page, you can modify security settings of the WLAN. Figure 124. The default security settings. By default, the Open network authentication type with no encryption is specified for the WLAN. ! The default security settings do not provide sufficient protection for the WLAN.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 125. Network authentication types supported by the access point. The access point supports the following authentication types: Authentication type Description Open Open authentication (with WEP encryption for wireless network modes not supporting 802.11n devices). Shared Shared key authentication with WEP encryption.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual When the Open or Shared value is selected, the WEP Encryption settings section is displayed (the section is unavailable for the wireless network operating modes which support the standard 802.11n): Figure 126. The Open value is selected from the Network Authentication drop-down list. Parameter Description The checkbox activating WEP encryption.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual When the WPA-PSK or WPA2-PSK value is selected, the WPA Encryption settings section is displayed: Figure 127. The WPA2-PSK value is selected from the Network Authentication drop-down list. Parameter Description Encryption Key PSK A key for WPA encryption. The key can contain digits and/or Latin characters.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual MAC Filter On the Wi-Fi / MAC Filter page, you can define a set of MAC addresses of devices which will be allowed to access the WLAN, or define MAC addresses of devices which will not be allowed to access the WLAN. Figure 128. MAC filters for the wireless network. By default, MAC filtering is not active (the Disabled choice of the MAC filter restrict mode radio button is selected).
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 129. The tab for adding a MAC address. Enter an address in the MAC address field of the MAC address adding section and click the Add button. To remove a MAC address from the list of MAC addresses, select the checkbox located to the right of the relevant MAC address in the MAC address list section and click the Delete button.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Station List On the Wi-Fi / Station List page, you can view the list of wireless clients connected to the access point. Devices connected to the access point via the WDS function are not displayed in the list. Figure 130. The list of the wireless clients.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual WPS On the Wi-Fi / WPS page, you can enable the function for secure configuration of the WLAN and select a method used to easily add wireless devices to the WLAN. The WPS function helps to configure the protected wireless network automatically. Devices connecting to the wireless network via the WPS function must support the WPS function.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual To activate the WPS function, select the WPS Enable checkbox and click the Change button. When the checkbox is selected, the Information and Connection sections are available on the page. Parameter Description Default PIN code The PIN code of the access point. This parameter is used when connecting the access point to a registrar to set the parameters of the WPS function.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Using WPS Function via Web-based Interface To add a wireless device via the PIN method of the WPS function, follow the next steps: 1. Select the WPS Enable checkbox. 2. Click the Change button. 3. Select the PIN value from the WPS Method drop-down list. 4. Select the PIN method in the software of the wireless device that you want to connect to the access point's WLAN. 5.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Later you will be able to add wireless devices to the WLAN by pressing the WPS/RESET button of the access point. 1. Select the PBC method in the software of the wireless device that you want to connect to the access point's WLAN. 2. Click the relevant button in the software or press the WPS button on the cover of the wireless device that you want to connect to the WLAN. 3.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual WDS On the Wi-Fi / WDS page, you can enable the WDS function and select a mode of this function. The WDS function allows joining local area networks together via a wireless connection of access points. Figure 132. The page for configuring the WDS function.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual The following fields are available on the page: Parameter Description The WDS function mode. Disable: The function is disabled. WDS Mode Bridge mode: Access points communicate to each other only, wireless devices cannot connect to them. Repeater mode: Access points communicate to each other, wireless clients can connect to the WLAN created by interconnected access points.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Additional Settings On the Wi-Fi / Additional settings page, you can define additional parameters for the WLAN of the access point. ! Changing parameters presented on this page may negatively affect your WLAN! Figure 133. Additional settings of the WLAN.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter TX Power Description The transmit power (in percentage terms) of the access point. The 802.11b and 802.11g protection function is used to minimize collisions between devices of your wireless network. Select a value from the drop-down list.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual WMM On the Wi-Fi / WMM page, you can enable the Wi-Fi Multimedia function. The WMM function implements the QoS features for Wi-Fi networks. It helps to improve the quality of data transfer over Wi-Fi networks by prioritizing different types of traffic. To enable the function, select the WMM checkbox and click the Change button. Figure 134. The page for configuring the WMM function.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual For every Access Category the following fields are available: Parameter Description Aifsn Arbitrary Inter-Frame Space Number. This parameter influences time delays for the relevant Access Category. The lower the value, the higher is the Access Category priority. CWMin/CWMax Contention Window Minimum/Contention Window Maximum. Both fields influence time delays for the relevant Access Category.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Client On the Wi-Fi / Client page in the router mode, you can configure the device as a client to connect to a WISP access point. The “client” function in the router mode allows using DAP-1155 as a WISP repeater. To use the access point as a WISP repeater, you need to configure the same channel of the wireless connection for DAP-1155 and the WISP access point.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 136. The page for configuring the client mode. To configure the access point as a client, select the Enable client checkbox. When the checkbox is selected, the following fields are displayed on the page: Parameter SSID Description The name of the network to which the access point connects. BSSID The unique identifier of the network to which the access point connects.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual When the Open or Shared authentication type is selected, the following fields are available: Parameter Description The checkbox activating WEP encryption. When the checkbox is selected, the Default Key ID field and four Encryption Key Enable Encryption WEP WEP fields are displayed on the page. For the Shared authentication type the checkbox is always selected.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Advanced In this menu you can configure advanced settings of the access point switched to the router mode: • enable the UPnP function • configure a DDNS service • add name servers • define static routes • create rules for remote access to the web-based interface • allow the access point to use IGMP.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual UPnP On the Advanced / UPnP page, you can enable and disable the UPnP function. UPnP is a set of networking protocols designed for automatic configuration of network devices. The UPnP function performs automatic configuration of the device's parameters for network applications requiring an incoming connection to the access point. Figure 137. The Advanced / UPnP page.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual DDNS On the Advanced / DDNS page, you can define parameters of the DDNS service, which allows associating a domain name with dynamic IP addresses. Figure 138. The Advanced / DDNS page. To add a new DDNS service, click the Add button.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 139. The page for editing the DDNS service. You can specify the following parameters: Parameter DDNS Service Description Select a DDNS provider from the drop-down list. Host name The domain name registered at your DDNS provider. User name The username to authorize for your DDNS provider. User password The password to authorize for your DDNS provider.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual DNS On the Advanced / DNS page, you can add DNS servers to the system. Figure 140. The Advanced / DNS page. DNS servers are used to determine the IP address from the name of a server in Intranets or the Internet (as a rule, they are specified by an ISP or assigned by a network administrator). The device performs the DNS relay function, i.e., it redirects the DNS requests of users to external DNS servers.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Routing On the Advanced / Routing page, you can add static routes (routes for networks that are not connected directly to the device but are available through the interfaces of the device) into the system. Figure 141. The Advanced / Routing page. To create a new route, click the Add button.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 142. The page for adding a static route. You can specify the following parameters: Parameter Description Destination network A destination network to which this route is assigned. Destination netmask The destination network mask. Gateway An IP address through which the destination network can be accessed. The filed is displayed when the value is selected from the Via Interface drop-down list.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Remote Access On the Advanced / Remote access page, you can configure access to the web-based interface of the access point. By default, the access from external networks to the access point is closed. If you need to allow access to the access point from the external network, create relevant rules. Figure 143. The Advanced / Remote access page. To create a new rule, click the Add button.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 144. The page for adding a rule for remote management. You can specify the following parameters: Parameter Description IP address A host or a subnet to which the rule is applied. To choose a device connected to the access point's LAN at the moment, select the relevant value from the drop-down list (the field will be filled in automatically). Mask The mask of the subnet.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual IGMP On the Advanced / IGMP page, you can enable IGMP for the access point. IGMP is used for managing multicast traffic (transferring data to a group of destinations). This protocol allows using network resources for some applications, e.g., for streaming video, more efficiently. Figure 145. The Advanced / IGMP page. To enable IGMP, select the Enabled checkbox.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Firewall In this menu you can configure the firewall of the access point switched to the router mode: • add rules for IP filtering • create virtual servers • define a DMZ • configure the MAC filter. IP Filters On the Firewall / IP filters page, you can create new rules for filtering IP packets and edit or remove existing rules. Figure 146. The Firewall / IP filters page.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 147. The page for adding a rule for IP filtering. You can specify the following parameters: Parameter Description IP filter rule editing Name Protocol A name for the rule for easier identification. A protocol for network packet transmission. Select a value from the drop-down list. Select an action for the rule.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description The source host/subnet IP address. If the IP address range checkbox is selected, specify the starting IP address of the range in the Source (first) field and the ending IP address in the Source (last) field. Source If the IP address range checkbox is not selected, specify the IP address of the host or subnet in the Source field. To specify an IP address add /32.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Virtual Servers On the Firewall / Virtual servers page, you can create virtual servers for redirecting incoming Internet traffic to a specified IP address in the local area network. Figure 148. The Firewall / Virtual servers page. To create a new virtual server, click the Add button.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 149. The page for adding a virtual server. You can specify the following parameters: Parameter Description Template Select a virtual server template from the drop-down list, or select Custom to specify all parameters of the new virtual server manually. Name A name for the virtual server for easier identification. You can specify any name.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Parameter Description Private IP The IP address of the server from the local area network. To choose a device connected to the access point's LAN at the moment, select the relevant value from the drop-down list (the field will be filled in automatically). Remote IP The IP address of the server from the external network. Click the Change button.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual DMZ A DMZ is a host or network segment located “between” internal (local) and external (global) networks. In the access point, the DMZ implements the capability to transfer a request coming to a port of the access point from the external network to a specified host of the internal network. On the Firewall / DMZ page you can specify the IP address of the DMZ host. Figure 150. The Firewall / DMZ page.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual MAC Filter On the Firewall / MAC filter page, you can configure MAC-address-based filtering for computers of the device's LAN. Figure 151. The Firewall / MAC filter page. To specify a new address for the MAC filter, click the Add button.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 152. The page for adding an address for the MAC filter. On the opened page, enter the MAC address of the device from the access point's LAN in the MAC address field. To choose a device connected to the access point's LAN at the moment, select the relevant value from the drop-down list (the field will be filled in automatically).
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Control This menu is designed to create restrictions on access to certain web sites. URL Filter On the Control / URL filter page, you can specify restrictions on access to certain web sites. Figure 153. The Control / URL filter page. The Configuration tab.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Figure 154. The Control / URL filter page. The URL addresses tab. On the opened page, specify the needed parameters. Figure 155. The page for adding an address for the URL filter. Enter a URL address in the URL address field and click the Save button.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual To remove an address from the list of URL addresses, select the relevant address in the table on the URL addresses tab and click the Delete button. To disable the URL filter, deselect the Enable/Disable URL filter checkbox on the Configuration tab, then click the Change button.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual System In this menu you can do the following: • change the password used to access the access point's settings • save the current settings to the non-volatile memory • create a backup of the access point's configuration • restore the access point's configuration from a previously saved file • restore the factory default settings • view the system log • update the firmware of the access point • config
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Administrator Password On the System / Administrator password page, you can change the password for the administrator account used to access the web-based interface of the access point and to access the device settings via TELNET. ! For security reasons, it is strongly recommended to change the administrator password upon initial configuration of the access point. Figure 156.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Configuration On the System / Configuration page, you can save the changed settings to the non-volatile memory, restore the factory defaults, backup the current configuration, or restore the device's configuration from a previously created file. Figure 157. The System / Configuration page.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual The following buttons are available on the page: Control Description Save Click the button to save settings to the non-volatile memory. Please, save settings every time you change the device's parameters. Otherwise the changes will be lost upon hardware reboot of the access point. Factory Click the button to restore the factory default settings.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual System Log On the System / System log page, you can set the system log options and configure sending the system log to a remote host. Figure 158. The System / System log page. The Configuration tab. To enable logging of the system events, select the Logging checkbox on the Configuration tab. Then specify the needed parameters. Control Description Select a type of logging from the drop-down list.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Control Description Port A port of the host specified in the Server field. By default, the value 514 is specified. After specifying the needed parameters, click the Change button. To disable logging of the system events, deselect the Logging checkbox and click the Change button. On the Log tab, the events specified in the Logging level list are displayed. Figure 159. The System / System log page. The Log tab.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Firmware Upgrade On the System / Firmware upgrade page, you can upgrade the firmware of the access point. ! Upgrade the firmware only when the access point is connected to your PC via a wired connection. Figure 160. The System / Firmware upgrade page. The current version of the access point's firmware is displayed in the Firmware version field located next the D-Link logo in the top left corner of the page.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual 6. Select the Factory line in the top-page menu displayed when the mouse pointer is over the System caption. 7. Wait until the access point is rebooted. Log into the web-based interface, using the default IP address, login and password (192.168.0.50, admin, admin).
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual NTP Client On the System / NTP client page, you can configure automatic synchronization of the system time with a time server on the Internet. Figure 161. The System / NTP client page. To enable automatic synchronization with a time server: 1. Select the Enabled checkbox. 2. Select your time zone. 3. Specify the needed NTP server in the NTP servers field or leave the server specified by default. 4.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Ping On the System / Ping page, you can check availability of a host from the local or global network via the Ping utility. The Ping utility sends echo requests to a specified host and receives echo replies. Figure 162. The System / Ping page.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Traceroute On the System / Traceroute page, you can define the route of data transfer to a host via the traceroute utility. Figure 163. The System / Traceroute page. To define the route, enter the name or IP address of a host in the Host field and click the Start button. After a while, the results will be displayed on the page.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Telnet On the System / Telnet page, you can enable or disable access to the device settings via TELNET from your LAN. By default, access is enabled. Figure 164. The System / Telnet page. To disable access via TELNET, deselect the On checkbox and click the Change button. To enable access via TELNET again, select the On checkbox.
DAP-1155 Wireless N 150 Access Point & Router Configuring Device (Router Mode) User Manual Device mode On the System / Device mode page, you can change the operating mode of the device. Figure 165. The page for changing the operating mode of the device. To switch the device to the other mode, select the Access point value from the Work mode drop-down list and click the Change button. In the opened dialog box, click the OK button to save new settings and immediately reboot the access point.
DAP-1155 Wireless N 150 Access Point & Router Operation Guidelines User Manual CHAPTER 6. OPERATION GUIDELINES Safety Instructions Place your access point on a flat horizontal surface or mount the access point on the wall (the mounting holes are located on the bottom panel of the device). Make sure that the access point is provided with sufficient ventilation. To prevent overheating, do not obstruct the ventilation openings of the access point.
DAP-1155 Wireless N 150 Access Point & Router Abbreviations and Acronyms User Manual CHAPTER 7.
DAP-1155 Wireless N 150 Access Point & Router Abbreviations and Acronyms User Manual PPPoE Point-to-point protocol over Ethernet PPTP Point-to-point tunneling protocol PSK Pre-shared key QoS Quality of Service RADIUS Remote Authentication in Dial-In User Service RIP Routing Information Protocol RTS Request To Send SSID Service Set Identifier TKIP Temporal Key Integrity Protocol UDP User Datagram Protocol UPnP Universal Plug and Play URL Uniform Resource Locator WAN Wide Area Netw
