Table of Contents Table of Contents Product Overview......................................................... 4 Package Contents.................................................... 4 System Requirements.............................................. 4 Introduction............................................................... 5 Features................................................................... 6 Hardware Overview.................................................. 7 Connections.......................
Table of Contents Connect to a Wireless Network Using Windows® XP........... 57 Configure WEP/WPA-PSK................................................59 Using Windows® Vista (Secured Network).....................60 Using Windows® Vista (Unsecured Network) ......... 63 Troubleshooting...............................................................66 Wireless Basics ......................................................... 68 Wireless Modes..........................................................
Section 1 - Product Overview Product Package Overview Contents • D-Link DAP-1150 Wireless G Access Point • Power Supply • Manual on CD • Quick Installation Guide • Ethernet Cable Note: Using a power supply with a different voltage rating than the one included with the DAP-1150 will cause damage and void the warranty for this product.
Section 1 - Product Overview Introduction D-Link, an industry leader in networking, introduces the new D-Link Wireless G Access Point(DAP-1150). With the ability to transfer files with a maximum wireless signal rate of up to 54Mbps1, the DAP-1150 gives you high-speed wireless network access for your home or office. The DAP-1150 is Wi-Fi IEEE 802.11g compliant, meaning that it can connect and interoperate with other 802.11g compatible wireless client devices. The 1150 is also backwards compatible to 802.
Section 1 - Product Overview Features • Multiple operation modes – Can be flexibly configured to operate as an Access Point, Wireless Client, Wireless Repeater mode. • Total security – Complete set of security features including WEP encryption and WPA/WPA2 to protect network against outside intruders. • Supports WPS(WiFi Protected Setup) on three operation modes. • Connect home and soho to a wireless network – Create a wireless network for your home and office using the D-Link DAP-1150 as an 802.
Section 1 - Product Overview Hardware Overview Connections Switch Button: Three-Way switch used to select AP. Repeater or wireless Client mode RESET: Pressing the Reset Button restores the access point to its original factory default settings. D-Link DAP-1150 User Manual LAN Port: Connect ethernet device such as computer, switch and hub. Power: Receptor for the Power Adapter.
Section 1 - Product Overview Hardware Overview LEDs Power: Solid green light indicates connection to a power source LAN:Blinking green light indicates activity;Solid green light indicates connection WLAN: Blinking green light indicates wireless activity;solid green light indicates connection D-Link DAP-1150 User Manual 8
Wireless Installation Considerations The D-Link wireless access point lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business.
AP/Repeater/Wireless Client Mode How you use your DAP-1150 will determine which mode you choose on the DAP-1150. This section will help you figure out which setting works with your setup. Access Point Mode In Access Point mode, the DAP-1150 acts as a central connection point for any computer (client) that has a 802.11g or backward-compatible 802.11b wireless network adapter and is within range of the AP. Clients must use the same SSID (wireless network name) and channel as the AP in order to connect.
Wireless Client Mode In AP Client mode, the DAP-1150 acts as a wireless network adapter for your Ethernet-enabled device (such as a game console or a TV set-top box). Connect your Ethernet-enabled device to the AP using an Ethernet cable. AP Client mode can support multiple wired clients.
Appendix A - Wireless Modes Repeater Mode Repeater mode increases the range of your wireless network by extending the wireless coverage of another AP or wireless router. The APs and wireless router (if used) must be within range of each other. Make sure that all clients, APs, and the wireless router all use the same SSID (wireless network name) and channel.
Section 3 - Configuration Configuration Web-based Configuration Utility If you wish to change the default settings or optimize the performance of the DAP-1150, you may use the configuration utility that D-Link has included a configuration utility for this purpose. After you have completed the initial installation, you can access the configuration menu, at any time, by opening the web-browser and typing in the device name of the DAP-1150. The DAP-1150’s default device name is shown below: 1.
Section 3 - Configuration Wireless Setup Wizard Click Launch Wireless Setup Wizard to quickly configure your access point. To setup your wireless network using WPS, you can click Add Wireless Device With WPS and skip to page 37.
Section 3 - Configuration Wireless Setup Wizard For AP Mode This Wizard is designed to assist you in connecting you wireless device to your access point. It will guide you through step-by-step instructions on how to get your wireless device connected. Click Launch Wireless Setup Wizard to begin. Click Launch Wireless Setup Wizard Enter the Device Name of the AP and click Next to continue. It is recommended to change the Device Name if there is more than one D-Link device within the subnet.
Section 3 - Configuration If you want to change the admin account password, enter a new password and click Next. Select Auto as the configuration method only if your wireless device supports Wi-Fi Protected Setup. Skip to next page for Manual configuration. Click Next to continue. Click Save to save your network settings.
Section 3 - Configuration In order for your network settings to take effect AP will reboot automatically. Click continue to return to the login page. Select Manual as the configuration method to setup your network manually. Click Next to continue.
Section 3 - Configuration Enter a network name and choose Automatically assign a network key. To Manually assign a network key, skip to page 19. Click Next to continue. If you choose WPA-PSK encryption, the following screen will show you your Network Key to enter on your wireless clients. Click Save to finish the Setup Wizard.
Section 3 - Configuration If you choose WEP encryption, the following screen will show you your Network Key to enter on your wireless clients. Click Save to finish the Setup Wizard. Choose Manually assign a network key to create you own key. Click Next to continue.
Section 3 - Configuration For WPA encryption, enter a Network Key between 8 and 63 characters long or enter exactly 64 characters using 0-9 and A-F. Click Next to continue. If you select WPA encryption, the following screen will show you your network key to enter on your wireless clients. Click Save to finish the Setup Wizard.
Section 3 - Configuration For WEP encryption, enter a Network Key exactly 5 or 13 characters long or exactly 10 or 26 characters using 0-9 and A-F. Click Next to continue. If you select WEP encryption, the following screen will show you your network key to enter on your wireless clients. Click Save to finish the Setup Wizard.
Section 3 - Configuration Setup Wizard For Repeater Mode This wizard is designed to assist you in configuring the wireless settings for your DAP-1150 with repeater mode. It will guide you through step-by-step instructions on how to setup your wireless network. You can click launch wireless setup wizard to quickly configure your access point.
Section 3 - Configuration If you want to change the admin account password, enter a new password and click Next. Select Auto configuration if you want to use Wi-Fi Protected Setup. If you want to setup your network manually, skip to page 26. Click Next to continue.
Section 3 - Configuration Select PIN to connect your wireless device with WPS. For PBC configuration, skip to next page. Enter the PIN number used into you access point and click Connect. Start WPS on the wireless device you are adding to you wireless network to complete the setup.
Section 3 - Configuration Select PBC to use the Push Button Configuration to connect to your network. Click Connect to continue. Press down the Push Button on the wireless device you are adding to your network to complete the setup.
Section 3 - Configuration Select Manual configuration to setup your network manually. Click Next to continue. If you clicked on Site Survey to following screen will be displayed. Find your access point from the list and click Connect to complete the Setup Wizard.
Section 3 - Configuration Choose which Security Mode you want to use and click Next to continue. If you choose WEP, enter the wireless security password and click Next to complete the Setup Wizard.
Section 3 - Configuration If you choose WPA, enter the WPA Personal Passphrase and click Next to complete the Setup Wizard. If you choose WPA2, enter the WPA2 Personal Passphrase and click Next to complete the Setup Wizard. The Wireless Setup Wizard is complete. Click Finish to reboot the device.
Section 3 - Configuration Setup Wizard For Wireless Client Mode This wizard is designed to assist you in configuring the wireless settings for your AP with wireless client mode. It will guide you through step-by-step instructions on how to setup your wireless network. Click Launch Wireless Setup Wizard to begin. Click Launch Wireless Setup Wizard Enter the Device Name of the AP and click Next to continue.
Section 3 - Configuration If you want to change the admin account password, enter a new password and click Next. Select Auto configuration if you want to use Wi-Fi Protected Setup. If you want to setup your network manually, skip to page 33. Click Next to continue.
Section 3 - Configuration Select PIN to connect your wireless device with WPS. For PBC configuration, skip to next page. Enter the PIN number used into you access point and click Connect. Start WPS on the wireless device you are adding to you wireless network to complete the setup.
Section 3 - Configuration Select PBC to use the Push Button Configuration to connect to your network. Click Connect to continue. Press down the Push Button on the wireless device you are adding to your network to complete the setup.
Section 3 - Configuration Select Manual configuration to setup your network manually. Click Next to continue. Enter the Wireless Network Name of the AP or use site survey to find the AP. Click Next to continue.
Section 3 - Configuration If you clicked on Site Survey to following screen will be displayed. Find your access point from the list and click Connect to complete the Setup Wizard.
Section 3 - Configuration Choose which Security Mode you want to use and click Next to continue. If you choose WEP, enter the wireless security password and click Next to complete the Setup Wizard.
Section 3 - Configuration If you choose WPA, enter the WPA Personal Passphrase and click Next to complete the Setup Wizard. If you choose WPA2, enter the WPA2 Personal Passphrase and click Next to complete the Setup Wizard. The Wireless Setup Wizard is complete. Click Finish to reboot the device.
Section 3 - Configuration Add Wireless Device With WPS This Wizard is designed to assist you in your wireless network setup. It will guide you through step-by-step instructions on how to set up your wireless network and how to make it secure. Select PIN to use your PIN number from your wireless device to connect to your network. For PBC configuration, skip to next page. Click Connect to continue. Start WPS on the wireless device you are adding to you wireless network to complete the setup.
Section 3 - Configuration Select PBC to use the Push Button Configuration to connect to your network. Click Connect to continue. Press down the Push Button on the wireless device you are adding to your network to complete the setup.
Section 3 - Configuration Wireless Setup Access Point In AP mode, the DAP-1150 acts as a central connection point for any computer (client) that has an 802.11g or backward-compatible 802.11b wireless network adapter and is within range of the AP. Wireless Network Name (also called the SSID): The Wireless Network Name is a unique name that identifies a network. All devices on a network must share the same wireless network name in order to communicate on the network.
Section 3 - Configuration Wi-Fi Protected Enable or disable the Wi-Fi protected setup feature. Setup: Lock Wireless Locking the wireless security prevents the settings from being changed by any new external registar using its PIN. Devices Security: can still be added to the wireless network using Wi-Fi Protected Setup. It is still possible to change wireless network settings with Manual Wireless Network Setup, Wireless Network Setup Wizard, or an existing external WLAN Manager Registar.
Section 3 - Configuration Repeater Wireless repeater mode extends the wireless coverage of another wireless AP or wireless router. Wireless Network Name (also called the SSID): The Wireless Network Name is a unique name that identifies a network. All devices on a network must share the same wireless network name in order to communicate on the network. If you decide to change the wireless network name from the default setting, enter your new wireless network name in this field.
Section 3 - Configuration Wireless Client In wireless client mode, the DAP-1150 acts as a wireless network adapter for your Ethernet-enabled device (such as a game console or a TV set-top box). Network Type: Select Infrastructure if you only connect your DAP-1150 to other wireless clients (as such wireless PCs). Select Ad-Hoc if you connect your DAP-1150 to another DAP-1150 operating in the Ad-Hoc mode.
Section 3 - Configuration LAN Setup The LAN (Local Area Network) is your private, internal network. This page allows you to configure the IP settings of the LAN interface for the DAP-1150. The IP address can be changed to your current network IP range. This IP address cannot be seen from the Internet.
Section 3 - Configuration LAN Settings My LAN Connection is: The DAP-1150 is set to Dynamic IP by default. . The IP address and subnet mask will fallback to 192.168.0.50 and 255.255.255.0, if don’t get IP address from DHCP server exceed 30 seconds. Static IP: Select this option if you are manually assigning an IP Address. Dynamic IP: Select this option if you would like to have an IP Address automatically assigned to the DAP1150 by a DHCP server in your network.
Section 3 - Configuration Advanced Wireless TX Rates: Transmit Power: Select the transmission rate for the network. Choose 100%, 50%(-3dB), 25% (-6dB), or 12.5% (-9dB). Beacon Interval: Beacons are packets sent by an access point to synchronize a wireless network. Specify a beacon interval value. The default value 100 is recommended. RTS Threshold: This value should remain at its default setting of 2,432.
Section 3 - Configuration Access Control Use MAC Filters to allow or deny wireless clients, by their MAC addresses, from accessing the DAP-1150. You can manually add a MAC address or select the MAC address from the list of clients that are currently connected to the AP (Connected PCs). The default setting is Disable MAC Filters. Access Access control is set to Disable by default. Control: Select Reject to deny access to the AP. Select Accept to allow access to the AP.
Section 3 - Configuration Maintenance Device Administration New Enter a new password. Password: Confirm Re-enter the password to confirm it. Password: Save and Restore Save Settings To Local Hard Drive: Click Save to save the current system settings as a file onto your local hard drive. Load Settings From Local Hard Drive: To load a system settings file, click on Browse to browse the local hard drive and locate the system settings file to be used.
Section 3 - Configuration Firmware Update This feature is used to update the firmware of the DAP-1150. The current firmware version and firmware date are displayed here. Click here to check for an update on our support site: Click this link and you will be connected to D-Link’s support website where you can download the latest firmware version to your local hard drive. Current Firmware Info: To update the firmware, click on Browse to browse the local hard drive and locate the updated firmware file.
Section 3 - Configuration Status Device Info This screen displays the current firmware version and the current LAN, and Wireless LAN settings on your access point.
Section 3 - Configuration Log The DAP-1150 keeps a running log of events and activities occurring on the AP. If the AP is rebooted, the logs are automatically cleared. You can save the log files under Log Setting. First Page: This button directs you to the first page of the log. Last Page: This button directs you to the last page of the log. Previous This button directs you to the previous Page: page of the log. Next Page: This button directs you to the next page of the log.
Section 3 - Configuration Statistics The DAP-1150 keeps statistics of the traffic that passes through it. You can view the amount of packets that pass through the LAN and wireless portions of the network. The traffic counter will reset if the access point is rebooted. Wireless This list displays the MAC addresses of connected wireless clients and the length of time that they have been connected.
Section 3 - Configuration Help The Help menu contains an index of links to help topics for each feature of the DAP-1150.
Section 4 - Security Wireless Security This section will show you the different levels of security you can use to protect your data from intruders.
Section 4 - Security Configure WEP It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration utility by opening a web browser and entering the device name of the access point (dlinkap). Click on Wireless Settings on the left side. 2.
Section 4 - Security What is WPA? WPA, or Wi-Fi Protected Access, is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy). There are 2 major improvements over WEP: • Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a hashing algorithm and by adding an integrity-checking feature ensures that the keys haven’t been tampered with.
Section 4 - Security Configure WPA-PSK, WPA2-PSK, and WPA2-Auto-PSK (Personal) It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration utility by opening a web browser and entering the device name of the access point (dlinkap).
Section 4 - Security Configure WPA-EAP, WPA2-EAP, and WPA2-Auto-EAP (Enterprise) It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration utility by opening a web browser and entering the device name of the access point (dlinkap).
Section 5 - Connecting to a Wireless Network Connect to a Wireless Network Using Windows® XP Windows® XP users can use the built-in wireless utility (Zero Configuration Utility) to connect to a wireless network. The following instructions are for Service Pack 2 users. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network.
Section 5 - Connecting to a Wireless Network Configure WEP/WPA-PSK It is recommended to enable WEP or WPA-PSK on your wireless access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WEP or WPA-PSK key being used. Follow the steps on the previous page to connect to a wireless network using Windows® XP. After you highlight a network and click Connect, the Wireless Network Connection box will appear if the network requires authentication.
Section 5 - Connecting to a Wireless Network Using Windows® Vista (Secured Network) The following are step-by-step directions to connect to a secured wireless network using Windows® Vista. 1. Right-click on Network and click on Properties. 2. Click the Manage network connections link in the Network and Sharing Center window.
Section 5 - Connecting to a Wireless Network 3. Right-click the Wireless Network Connection entry and then select Connect/Disconnect from the drop-down menu. 4. Select a network to connect to in the Select a network to connect to window and then click the Connect button. 5. The following window displays connection progress.
Section 5 - Connecting to a Wireless Network 6. Enter the network security key or passphrase for the AP in the textbox provided in the Type the network security key or passphrase for [SSID name] window. When you are finished, click the Connect button. 7. The following Successfully connected to [SSID name] window is displayed. Choose to save this network and/or start this new connection automatically. When you are finished, click the Close button.
Section 5 - Connecting to a Wireless Network Using Windows® Vista (Unsecured Network) The following are step-by-step directions to set up a wireless connection on an unsecured network using Windows® Vista. 1. Right-click on Network and click on Properties. 2. Go to the Network and Sharing Center window and click the Manage Network Connections link.
Section 5 - Connecting to a Wireless Network 3. Right-click the Wireless Network Connection entry and then select Connect/Disconnect from the drop-down menu. 4. Select a network to connect to in the Select a network to connect to window and then click the Connect button. 5. Confirm that you still want to connect on the following Network Connection Status window by clicking on Connect Anyway.
Section 5 - Connecting to a Wireless Network 6. The following Connect to a network wizard window displays the connection progress. 7. The following Successfully connected to [SSID name] window is displayed. Choose to save this network and/or start this new connection automatically. When you are finished, click the Close button.
Section 6 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DAP-1150. Read the following descriptions if you are having problems. The examples below use Windows® XP. If you have a different operating system, the troubleshooting steps may be different from the following examples. 1.
Section 6 - Troubleshooting • Configure your Internet settings: • Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. • Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. • Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
Appendix B - Wireless Basics Wireless Basics D-Link wireless products are based on the latest industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business, or public wireless networks. Strictly adhering to IEEE standards, the D-Link wireless family of products allows you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers.
Appendix B - Wireless Basics What is Wireless? Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio waves to connect wirelessly, so you have the freedom to connect computers anywhere in your home or office network. Why D-Link Wireless? D-Link is a worldwide leader and an award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford.
Appendix B - Wireless Basics Wireless Personal Area Network (WPAN) Bluetooth is the industry standard wireless technology used for WPANs. Bluetooth devices in WPANs operate in a range up to 30 feet away. The speed and wireless operation range of a WPAN is less than of a WLAN, but it excels in its efficient consumption of power. WPANs are ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries.
Appendix B - Wireless Basics Where is wireless used? Wireless technology is quickly expanding beyond home and office use. The freedom of mobility it offers is becoming so popular that more and more public facilities are now providing wireless access to attract people. Public places that offer wireless access is usually called a “hotspot”.
Appendix B - Wireless Basics Security Don’t let your next-door neighbors or unwanted intruders connect to your wireless network. Secure your wireless network by turning on the WEP or WPA security feature on the access point. Refer to the section “Wireless Security” in this manual for detailed information on how to set it up. Wireless Modes There are basically two modes of networking: • Infrastructure – All wireless clients will connect to an access point or wireless router.
Appendix C - Networking Basics Networking Basics Check your IP address After you install your network adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. At the prompt, type ipconfig and press Enter. This will display the IP address, subnet mask, and the default gateway of your adapter. If the address is 0.
Appendix C - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Step 1 Windows® XP - Click on Start > Control Panel > Network Connections. Windows® 2000 - From the desktop, right-click My Network Places > Properties. Step 2 Right-click on the Local Area Connection which represents your network adapter and select Properties.
Appendix D - Technical Specifications Technical Specifications NETWORK STANDARDS - 802.11g wireless LAN - 802.11b wireless LAN - 802.3/802.3u 10BASE-T/100BASE-TX Ethernet - ANSI/IEEE 802.3 NWay auto-negotiation DEVICE INTERFACES - 802.11g wireless LAN - One 10/100BASE-TX Ethernet LAN port OPERATING FREQUENCY 2.4 to 2.4835 GHz OPERATING CHANNELS - FCC: 11 - ETSI: 13 RADIO & MODULATION SCHEMES DQPSK, DBPSK, CCK, OFDM OPERATION MODES - Access Point - Repeater - Wireless Client RECEIVE SENSITIVITY +For 802.
Appendix D - Technical Specifications SECURITY - 64/128-bit WEP data encryption - WPA-PSK, WPA2-PSK - WPA-EAP, WPA2-EAP - TKIP, AES - MAC address filtering - SSID broadcast disable function QUALITY OF SERVICE (QoS) Wi-Fi Multimedia (WMM) DEVICE MANAGEMENT - Web-based management through Internet Explorer v.6 or later, Netscape Navigator v.
Version 1.
