Table of Contents Table of Contents Product Overview......................................................... 4 Package Contents.................................................... 4 System Requirements.............................................. 4 Introduction............................................................... 5 Features................................................................... 6 Hardware Overview.................................................. 7 Installation......................
Table of Contents Troubleshooting......................................................... 59 Wireless Basics.......................................................... 63 Networking Basics..................................................... 68 Check your IP address........................................... 68 Windows® XP/2000 Users................................ 68 Windows Vista™ Users...................................... 68 Statically Assign an IP address..............................
Section 1 - Product Overview Product Overview Package Contents • D-Link WUA-1340 Wireless G USB Adapter • Cradle • Manual and Warranty on CD • D-Link Wireless Connection Manager on CD • Quick Installation Guide System Requirements • A computer or laptop with an available USB 2.0 port • Windows® Vista™, XP (Service Pack 2) or 2000 (Service Pack 4) • CD-ROM Drive • 500MHz processor and at least 64MB of RAM • An 802.
Section 1 - Product Overview Introduction D-Link, the industry pioneer in wireless networking, introduces the WUA-1340 Wireless USB Adapter, part of the Wireless G family of 802.11g wireless networking devices. Using the WUA-1340 Wireless USB Adapter, you can now enable 802.11g wireless connectivity for your PC using the convenience and speed of a USB 2.0 interface**. Featuring the latest in wireless technology, the WUA-1340 delivers incredibly fast performance and industrywide compatibility.
Section 1 - Product Overview Features • Provides maximum wireless signal rate of up to 54Mbps*. • Compact size for placement anywhere. • Convenience of Plug & Play installation. • Fully 802.11b/802.11g compatible. • Powered by the USB port; no external power source required. • USB 2.0 standard**. • You can securely connect to a wireless network using WPATM /WPA2TM (Wi-Fi Protected Access)providing you a much higher level of security for your data and communication that has previously been available.
Section 1 - Product Overview Hardware Overview Link Light A blinking light indicates activity on your wireless network. USB Port Used to connect the WUA-1340 to your computer.
Section 2 - Installation Installation This section will walk you through the installation process. If you have a built-in wireless adapter, please disable it in device manager before installing your D-Link adapter. Also, if you have previously installed another wireless adapter, please make sure any software is uninstalled.
Section 2 - Installation Disable Other Wireless Adapters Most newer laptops may include a built-in wireless adapter. To prevent any conflicts with the D-Link wireless adapter, it is recommended to disable the wireless adapter (as well as any unused Ethernet adapters). From the desktop, right-click on the My Computer icon and select Properties. Click the Hardware tab and then click Device Manager. Scroll down the list and click the + sign to the left of Network Adapters.
Section 2 - Installation Click Yes to disable the adapter. The adapter is now disabled. When disabled, a red X will be displayed. Disabling the adapter will not remove the drivers. If you would like to use the adapter, simply right-click it and select Enable.
Section 2 - Installation Wireless Installation Considerations The D-Link wireless adapter lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range.
Section 2 - Installation Software Installation Warning: Do NOT install the WUA-1340 USB Adapter into your computer before installing the driver software from the D-Link CD. Turn on the computer and Insert the D-Link WUA-1340 Driver CD in the CD-ROM drive. If the CD Autorun function does not automatically start on your computer, go to Start > Run. In the run box type “D:\WUA-1340.exe” (where D: represents the drive letter of your CD-ROM drive). Click Install Drivers.
Section 2 - Installation Windows Vista™ Installation The InstallShield Wizard window will appear. Click Next to continue. By default setup will install to the default location: C:\Program Files\D-Link\WUA-1340, where C: represents the drive letter of your hard drive. To install to a different location click Browse and specify the location. Click Next to continue.
Section 2 - Installation Select the Program Files folder location. Click Next to continue. Insert the adapter into an available USB port on your computer. If the Found New Hardware Wizard appears, click Cancel. The Wireless Connection Wizard will now appear. If you want to manually connect to a wireless network, refer to page 16. The following instructions will connect you to a wireless network using Wi-Fi Protected Setup (WPS).
Section 2 - Installation Push Button Configuration (PBC) To connect to your network using the WPS push button configuration method, click the virtual button as shown in the screenshot. Press the WPS button on your access point or wireless router within 2 minutes to establish connectivity. When this screen appears, you have successfully connected to your wireless network. Click Next to complete your setup.
Section 2 - Installation To manually connect to your wireless network, select Manually connect to a wireless network and then click Next. Enter the network name (SSID) manually. If you enter the SSID incorrectly, you will automatically be brought to the site survey page. Click Scan to display the site survey page. Click the Scan button to display a list of wireless networks (site survey). Click on the network name (SSID) and click Next.
Section 2 - Installation When this screen appears, you are successfully connected to your wireless network. Click Next to complete your setup. Click Finish to continue. If you are prompted to reboot your computer, select Yes, I want to restart my computer now.
Section 2 - Installation Windows® XP Installation The InstallShield Wizard window will appear. Click Next to continue. By default setup will install to the default location: C:\Program Files\D-Link\WUA-1340, where C: represents the drive letter of your hard drive. To install to a different location click Browse and specify the location. Click Next to continue. Select the Program Files folder location. Click Next to continue.
Section 2 - Installation The D-Link configuration wizard will now appear. If you are using Windows® XP (SP2), you will have the option to use either the D-Link utility or the built-in Windows® Wireless utility. Click Next to continue. Insert the adapter into an available USB port on your computer. Optional: If desired or necessary, attach the cradle between the WUA-1340 and your computer. If the Found New Hardware Wizard appears, click Cancel. Click Next to continue.
Section 2 - Installation Push Button Configuration (PBC) To connect to your network using the WPS push button configuration method, click the virtual button as shown in the screenshot. Press the WPS button on your access point or wireless router within 2 minutes to establish connectivity. When this screen appears, you have successfully connected to your wireless network. Click Next to complete your setup.
Section 2 - Installation To manually connect to your wireless network, select Manually connect to a wireless network and then click Next. Enter the network name (SSID) manually. If you enter the SSID incorrectly, you will automatically be brought to the site survey page. Click Next to continue or click Scan to display the site survey page. Click the Scan button to display a list of wireless networks (site survey). Click on the network name (SSID) and click Connect.
Section 2 - Installation If the wireless network you are trying to connect to is using WEP, enter the WEP key. Click Next to continue. If the wireless network you are trying to connect to is using WPAPSK, enter the WPA-PSK passphrase. Click Next to continue. Click Finish to continue. If you are prompted to reboot your computer, select Yes, I want to restart my computer now.
Section 3 - Configuration Configuration This section will show you how to configure your new D-Link wireless adapter using the D-Link Utility as well as the Windows® XP Zero Configuration Utility. D-Link Wireless Connection Manager The D-Link WUA-1340 uses the Wireless Connection Manager as the management software. The manager provides the user an easy interface to change any settings related to the wireless adapter.
Section 3 - Configuration Windows Vista Wireless Networks The Wireless Networks (Site Survey) page will display all wireless networks that are available in your area. To connect to a network, simply highlight the wireless network (SSID) and click Connect. SSID: The SSID (Service Set Identifier) is the name of the wireless network. MAC: Displays the MAC address of the wireless device. Signal: Displays the Link Quality of the wireless connection.
Section 3 - Configuration Wi-Fi Protected Setup (WPS) Wi-Fi Protected Setup (WPS) System is designed for easy setup of security-enabled Wi-Fi networks. It is recommended to have the access point or wireless router nearby during setup. For more information on WPS, visit the Wi-Fi Alliance website at www.wi-fi.org. “Push Button Configuration” (PBC) is a virtual button in the utility that connects you to other WPS-enabled devices.
Section 3 - Configuration Personal Identification Number (PIN) If you want to connect using the PBC method, refer to page 20. To use the PIN method, select PIN (Personal Identification Number) and click Next. Make sure your access point or wireless router is close by. Write down the number on the screen. Enter this number in your access point or wireless router. Please refer to the manufacture’s manual for instructions.
Section 3 - Configuration The adapter will try to establish connectivity to your access point or wireless router. When this screen appears, you have successfully established connectivity. Click Finish to complete your setup.
Section 3 - Configuration My Wireless Networks The My Wireless Networks page will allow you to create, edit, and delete wireless network profiles. Every time you connect to a network using the Wireless Networks page, a profile will automatically be created. New Button: Click New to create a new wireless network profile (refer to page 29). Modify: Click Modify to edit a current profile (refer to page 30). Delete: Click Delete to remove a profile. Active: Click Active to activate a profile.
Section 3 - Configuration Add Profile You may add a new network by clicking the New button from the My Wireless Networks page. Profile Name: Enter a name for your profile (e.g. Home, Office, Coffee Shop). SSID: Enter the SSID of the wireless network. Network Type: Select the network type. If you are connecting to a wireless router or access point, select Infrastructure. If you are connecting to another wireless client such as an adapter, select Ad-Hoc. Set Security: Select the type of security used.
Section 3 - Configuration Modify Profile You may edit an existing profile by clicking the Modify button from the My Wireless Networks page. Profile Name: Enter a name for your profile (e.g. Home, Office, Coffee Shop). SSID: Displays the SSID of the network. Network Type: Displays the network type. Set Security: Select the type of security used. Please refer to the Wireless Security section for more information. OK Button: Click OK to save your settings.
Section 3 - Configuration Support If you need help, click the Support button. A pane will appear to the right of the utility which will display information about the utility.
Section 3 - Configuration About The About screen gives you information about the Firmware and Utility Versions of the WUA-1340.
Section 3 - Configuration Windows® XP Wireless Networks The Wireless Networks (Site Survey) page will display all wireless networks that are available in your area. To connect to a network, simply highlight the wireless network (SSID) and click Connect. SSID: The SSID (Service Set Identifier) is the name of the wireless network. MAC: Displays the MAC address of the wireless device. Signal: Displays the Link Quality of the wireless connection.
Section 3 - Configuration Wi-Fi Protected Setup (WPS) Wi-Fi Protected Setup (WPS) System is designed for easy setup of security-enabled Wi-Fi networks. It is recommended to have the access point or wireless router nearby during setup. For more information on WPS, visit the Wi-Fi Alliance website at www.wi-fi.org. “Push Button Configuration” (PBC) is a virtual button in the utility that connects you to other WPS-enabled devices.
Section 3 - Configuration Personal Identification Number (PIN) If you want to connect using the PBC method, refer to page 20. To use the PIN method, select PIN (Personal Identification Number) and click Next. Make sure your access point or wireless router is close by. Write down the number on the screen. Enter this number in your access point or wireless router. Please refer to the manufacture’s manual for instructions.
Section 3 - Configuration The adapter will try to establish connectivity to your access point or wireless router. When this screen appears, you have successfully established connectivity. Click Finish to complete your setup.
Section 3 - Configuration My Wireless Networks The My Wireless Networks page will allow you to create, edit, and delete wireless network profiles. Every time you connect to a network using the Wireless Networks page, a profile will automatically be created. New Button: Click New to create a new wireless network profile (refer to page 38). Modify: Click Modify to edit a current profile (refer to page 39). Delete: Click Delete to remove a profile. Active: Click Active to activate a profile.
Section 3 - Configuration Add Profile You may add a new network by clicking the New button from the My Wireless Networks page. Profile Name: Enter a name for your profile (e.g. Home, Office, Coffee Shop). SSID: Enter the SSID of the wireless network. Network Type: Select the network type. If you are connecting to a wireless router or access point, select Infrastructure. If you are connecting to another wireless client such as an adapter, select Ad-Hoc. Set Security: Select the type of security used.
Section 3 - Configuration Modify Profile You may edit an existing profile by clicking the Modify button from the My Wireless Networks page. Profile Name: Enter a name for your profile (e.g. Home, Office, Coffee Shop). SSID: Displays the SSID of the network. Network Type: Displays the network type. Set Security: Select the type of security used. Please refer to the Wireless Security section for more information. OK Button: Click OK to save your settings.
Section 3 - Configuration Support If you need help, click the Support button. A pane will appear to the right of the utility which will display information about the utility.
Section 3 - Configuration About The About screen gives you information about the Firmware and Utility Versions of the WUA-1340.
Section 3 - Configuration Connect to a Wireless Network Using Windows Vista™ Windows® Vista™ users may use the built-in wireless utility. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® Vista™ utility as seen below.
Section 3 - Configuration Enter the same security key or passphrase that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
Section 3 - Configuration Connect to a Wireless Network Using Windows® XP Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.
Section 3 - Configuration Disabling The Windows® XP Utility If you want to use the D-Link wireless utility you must disable the Windows® XP wireless utility. Right-click on the wireless computer icon in your system tray (lower-right corner next to the time). Select View Available Wireless Networks. In the Choose a Wireless Network window click Change Advanced Settings on the left side below Related Tasks.
Section 3 - Configuration In the Wireless Network Connection Properties window, uncheck Use Windows® to configure my wireless network settings and then click OK.
Section 4 - Security Wireless Security This section will show you the different levels of security you can use to protect your data from intruders.
Section 4 - Security What is WPA? WPA, or Wi-Fi Protected Access, is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy). The 2 major improvements over WEP: • Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a hashing algorithm and, by adding an integrity-checking feature, ensures that the keys haven’t been tampered with. WPA2 is based on 802.11i and uses Advanced Encryption Standard instead of TKIP.
Section 4 - Security Configure WPA/WPA2 Passphrase Using the D-Link Utility It is recommended to enable WPA-PSK on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WPA-PSK passphrase being used. 1. Open the Wireless Connection Manager by double-clicking on the D-Link icon on your desktop. 2. Highlight the wireless network (SSID) you would like to connect to and click Connect.
Section 4 - Security It is recommended to enable WPA-PSK on your wireless router or access point before configuring your wireless adapter. Make sure you enter the passphrase exactly the same on all wireless devices. 1. Open the Wireless Connection Manager by double-clicking on the D-Link icon on your desktop. Click on New to create a new profile or highlight an existing profile and click Modify. 2. Select WPA/WPA2 Passphrase under Set Security Option. 3. Select TKIP or AES. 4.
Section 4 - Security Configure WPA/WPA2 Passphrase Using the Windows® Vista Utility It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Open the Windows® Vista™ Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower right corner of screen). Select Connect to a network. 2.
Section 4 - Security 3. Enter the same security key or passphrase that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
Section 4 - Security Configure WPA/WPA2 Passphrase Using the Windows® XP Utility It is recommended to enable WPA-PSK on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WPA-PSK key being used. 1. Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks. 2.
Section 4 - Security 3. The Wireless Network Connection box will appear. Enter the WPA-PSK passphrase and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The WPA-PSK passphrase must be exactly the same as on the wireless router or access point.
Section 4 - Security Configure WPA/WPA2 Using the D-Link Utility WPA and WPA2 are for advanced users who are familiar with using a RADIUS server and setting up certificates. 1. Open the Wireless Utility by double-clicking on the D-Link icon in your system tray (lower-right corner of screen). Click on New to create a new profile or highlight an existing profile and click Modify. 2. Select WPA/WPA2 (XP) or WPA/WPA2-EAP (Vista) under Set Security Option and then select TKIP or AES. 3.
Section 4 - Security 4. Next to EAP Type, select EAP-TLS, EAP-TTLS, or PEAP. Extensible Authentication Protocols allow devices on the network to request authentication from the RADIUS server in the network. All the devices on the network must use the same EAP type when using a RADIUS server for authentication. Some RADIUS servers require that the Validate Server field be selected. Check this field if your RADIUS server requires validation. 5. Select an User Certificate from the drop-down menu. 6.
Section 4 - Security Configure 802.1x Using the D-Link Utility 802.1x is for advanced users who are familiar with using a RADIUS server and setting up certificates. 1. Open the Wireless Utility by double-clicking on the D-Link icon in your system tray (lower-right corner of screen). Click on New to create a new profile or highlight an existing profile and click Modify. 2. Select 802.1x under Set Security Option. 3. Click on Advanced Config to continue.
Section 4 - Security 4. Next to EAP Type, select EAP-TLS, LEAP, EAP-TTLS, or PEAP. Extensible Authentication Protocols allow devices on the network to request authentication from the RADIUS server in the network. All the devices on the network must use the same EAP type when using a RADIUS server for authentication. Some RADIUS servers require that the Validate Server field be selected. Check this field if your RADIUS server requires validation. 5. Select an User Certificate from the drop-down menu. 6.
Section 5 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the WUA-1340. Read the following descriptions if you are having problems. 1. How do I know if my adapter is installed properly? Windows Vista™ users - Open the Start menu, rightclick on Computer and select Manage. Click on Device Manager in the left-hand side.
Section 5 - Troubleshooting Click the + sign next to Network Adapters. Right-click on D-Link WUA-1340 Cardbus Adapter. Select Properties to check that the drivers are installed properly. Look under Device Status to check that the device is working properly. Click OK to continue.
Section 5 - Troubleshooting 2. The computer does not recognize the WUA-1340 Wireless Adapter. Make sure that the WUA-1340 Wireless Adapter is properly seated in the computer’s USB slot. If Windows® does not detect the hardware upon insertion of the adapter, make sure to completely remove drivers that were previously loaded. 3. The computer with the WUA-1340 installed is unable to connect to the wireless network and/or the Internet.
Section 5 - Troubleshooting Check that the Network Connection for the wireless client is configured properly. Select AP (Infrastructure) when connecting to an access point and select Ad-Hoc mode when connecting without an access point. Double-click on the WLAN icon in the taskbar > click on Configuration to change the settings for the wireless adapter. If Security is enabled, make sure that the correct encryption keys are entered on both the WUA-1340 and the access point.
Appendix A - Wireless Basics Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers.
Appendix A - Wireless Basics What is Wireless? Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or office network. Why D-Link Wireless? D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford.
Appendix A - Wireless Basics Wireless Personal Area Network (WPAN) Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away. Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries.
Appendix A - Wireless Basics Where is wireless used? Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and it’s becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called “hotspots”.
Appendix A - Wireless Basics Security Don’t let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or WEP security feature on the router. Refer to product manual for detail information on how to set it up. Wireless Modes There are basically two modes of networking: • Infrastructure – All wireless clients will connect to an access point or wireless router.
Appendix B - Networking Basics Networking Basics Check your IP address After you install your new D-Link wireless adapter and have established a wireless connection, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. router) automatically. To verify your IP address, please follow the steps below. Windows® XP/2000 Users • Click on Start > Run. In the run box type cmd and click OK. • At the prompt, type ipconfig and press Enter.
Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Windows® XP/2000 Users • Windows® XP - Click on Start > Control Panel. Make sure you are in Classic View. Double-click on the Network Connections icon. Windows® 2000 – From the desktop, right-click My Network Places > Properties.
Appendix B - Networking Basics Windows Vista™ Users • Click on Start > Control Panel. Make sure you are in Classic View. Double-click on the Network and Sharing Center icon. Along the left panel in the window, click on Manage network connections. • Right-click on the Local Area Connection which represents your D-Link wireless network adapter which will be connected to your network. • Highlight Internet Protocol Version 4 (TCP /IPv4) and click Properties.
Appendix C - Technical Specifications Technical Specifications Standards • IEEE 802.11b • IEEE 802.11g Bus Type • USB 2.0 Wireless Signal Rates* • 54Mbps • 48Mbps • 36Mbps • 24Mbps • 18Mbps • 12Mbps • 11Mbps • 9Mbps • 6Mbps • 5.5Mbps • 2Mbps • 1Mbps Security • WPA/WPA2 - Wi-Fi Protected Access (TKIP, MIC, IV Expansion, Shared Key Authentication) • 802.1x • 64/128-bit WEP Media Access Control • CSMA/CA with ACK Frequency Range • 2.4GHz to 2.
Appendix D - Contacting Technical Support Contacting Technical Support D-Link provides free technical support for customers within the United States and within Canada for the duration of the warranty period on this product. U.S. and Canadian customers can contact D-Link technical support through our web site or by phone. Before you contact technical support, please have the following ready: • Model number of the product (e.g. WUA-1340) • Hardware Revision (located on the label on the adapter (e.g.
Appendix E - Warranty Warranty Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty: • Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and • Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.
Appendix E - Warranty Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90) days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation.
Appendix E - Warranty Number at https://rma.dlink.com/. • After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not include any manuals or accessories in the shipping package. DLink will only replace the defective portion of the product and will not ship back any accessories.
Appendix E - Warranty IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF THE PRODUCT.
Appendix E - Warranty Copyright ©2007 by D-Link Corporation/D-Link Systems, Inc. All rights reserved. CE Mark Warning: This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Registration Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Version 1.
