Document Created by Nick Schuster
D-Link DAP-2620 User Manual Package Contents • DAP-2620 Access Point • Mounting Plate and Hardware Note: Using a power supply with a different voltage rating than the one included with the DAP-2620 will cause damage and void the warranty for this product.
D-Link DAP-2620 User Manual Basic Installation Hardware Setup To power the access point, you can use one of the following 3 methods: Method 1 - Use if you have a PoE switch or router. Method 1 - PoE with PoE Switch or Router 1. Connect one end of your Ethernet cable to the LAN (PoE) port on the access point. 2. Connect the other end into one port on a PoE switch or router.
D-Link DAP-2620 User Manual Web User Interface The DAP-2620 supports an elaborate web user interface where the user can configure and monitor the device. Launch a web browser, type the IP address of the access point (Default setting is http://192.168.0.50 or https://192.168.0.50) and then press Enter to login. Most of the configurable settings are located in the left menu of the web GUI which contains section called Basic Settings, Advanced Settings and Status.
D-Link DAP-2620 User Manual Wireless On the wireless settings page, you can setup the basic wireless configuration for the access point.
D-Link DAP-2620 User Manual Channel: To change the channel, first toggle the Auto Channel Selection setting to Disable, and then use the drop-down menu to make the desired selection. Note: The wireless adapters will automatically scan and match the wireless settings. Channel Width: Allows you to select the channel width you would like to operate in. Select 20 MHz if you are not using any 802.11n wireless clients. Auto 20/40 MHz allows you to connect to both 802.11n and 802.11b/g or 802.
D-Link DAP-2620 User Manual WDS with AP Mode Wireless Band: Select either 2.4GHz or 5GHz from the drop-down menu. Mode: WDS with AP mode is selected from the drop-down menu. Network Name (SSID): Service Set Identifier (SSID) is the name designated for a specific wireless local area network (WLAN). The SSID’s factory default setting is dlink. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network. SSID Visibility: Enable or Disable SSID visibility.
D-Link DAP-2620 User Manual Remote AP MAC Address: Enter the MAC addresses of the APs on your network that will serve as bridges to wirelessly connect multiple networks. Site Survey: Click on the Scan button to search for available wireless networks, then click on the available network that you want to connect with. Authentication: Use the drop-down menu to choose Open System, Shared Key, or WPA-Personal. • Select Open System to communicate the key across the network.
D-Link DAP-2620 User Manual WDS Mode Wireless Band: Select either 2.4GHz or 5GHz from the drop-down menu. Mode: WDS is selected from the drop-down menu. Network Name (SSID): Service Set Identifier (SSID) is the name designated for a specific wireless local area network (WLAN). The SSID’s factory default setting is dlink. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network. SSID Visibility: Enable or Disable SSID visibility.
D-Link DAP-2620 User Manual Site Survey: Click on the Scan button to search for available wireless networks, then click on the available network that you want to connect with. Authentication: Use the drop-down menu to choose Open System, Shared Key, or WPA-Personal. • Select Open System to communicate the key across the network. • Select Shared Key to limit communication to only those devices that share the same WEP settings.
D-Link DAP-2620 User Manual Wireless Client Mode Wireless Band: Select either 2.4 GHz or 5 GHz from the drop-down menu. Mode: Wireless Client is selected from the drop-down menu. Network Name (SSID): Service Set Identifier (SSID) is the name designated for a specific wireless local area network (WLAN). The SSID’s factory default setting is dlink. The SSID can be easily changed to connect to an existing wireless network. SSID Visibility: This option is unavailable in Wireless Client mode.
D-Link DAP-2620 User Manual Wireless Security Wireless security is a key concern for any wireless network installed. Unlike any other networking method wireless networks will broadcast it’s presence for anyone to connect to it. Today, wireless security has advanced to a level where it is virtually impenetrable. There are mainly two forms of wireless encryption and they are called Wired Equivalent Privacy (WEP) and Wi-Fi Protected Access (WPA). WEP was the first security method developed.
D-Link DAP-2620 User Manual Wi-Fi Protected Access (WPA / WPA2) WPA was created by the Wi-Fi Alliance to address the limitations and weaknesses found in WEP. This protocol is mainly based on the 802.11i standard. There are also two variations found in WPA called WPA-Personal (PSK) and WPA-Enterprise (EAP). WPA-EAP requires the user to install a Radius Server on the network for authentication. WPA-Personal does not require the user to install a Radius Server on the network.
D-Link DAP-2620 User Manual WPA Mode: When WPA-Enterprise is selected, you must also select a WPA mode from the drop-down menu: AUTO (WPA or WPA2), WPA2 Only, or WPA Only. WPA and WPA2 use different algorithms. AUTO (WPA or WPA2) allows you to use both WPA and WPA2. Cipher Type: When WPA-Enterprise is selected, you must also select a cipher type from the drop-down menu: Auto, AES, or TKIP. Group Key Update Interval: Select the interval during which the group key will be valid.
D-Link DAP-2620 User Manual LAN LAN is short for Local Area Network. This is considered your internal network. These are the IP settings of the LAN interface for the DAP-2620. These settings may be referred to as private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet. Get IP From: Static IP (Manual) is chosen here.
D-Link DAP-2620 User Manual IPv6 Enable IPv6: Check to enable the IPv6 Get IP From: Auto is chosen here. Choose this option the DAP-2620 can get IPv6 address automatically or use Static to set IPv6 address manually. When Auto is selected, the other fields here will be grayed out. IP Address: Enter the LAN IPv6 address used here. Prefix: Enter the LAN subnet prefix length value used here. Default Gateway: Enter the LAN default gateway IPv6 address used here.
D-Link DAP-2620 User Manual Advanced Settings In the Advanced Settings Section the user can configure advanced settings concerning Performance, Multiple SSID, VLAN, Security, Quality of Service, AP Array, Web Redirection, DHCP Server, Filters and Scheduling. The following pages will explain settings found in the Advanced Settings section in more detail.
D-Link DAP-2620 User Manual Performance On the Performance Settings page the users can configure more advanced settings concerning the wireless signal and hosting. Wireless Band: Select either 2.4GHz or 5GHz. Wireless: Use the drop-down menu to turn the wireless function On or Off. Wireless Mode: The different combination of clients that can be supported include Mixed 802.11n, 802.11g and 802.11b, Mixed 802.11g and 802.11b and 802.11n Only in the 2.4 GHz band and Mixed 802.11n, 802.11a, 802.
D-Link DAP-2620 User Manual Transmit Power: This setting determines the power level of the wireless transmission. Transmitting power can be adjusted to eliminate overlapping of wireless area coverage between two access points where interference is a major concern. For example, if wireless coverage is intended for half of the area, then select 50% as the option. Use the drop-down menu to select 100%, 50%, 25%, or 12.5%. WMM (Wi-Fi Multimedia): WMM stands for Wi-Fi Multimedia.
D-Link DAP-2620 User Manual Wireless Resource Control The Wireless Resource Control window is used to configure the wireless connection settings so that the device can detect the better wireless connection in your environment. Wireless band: Select 2.4GHz or 5GHz. Band Steering: Use the drop-down menu to Enable the 5G Preferred function. When the wireless clients support both 2.4GHz and 5GHz and the 2.4GHz signal is not strong enough, the device will use 5G as higher priority.
D-Link DAP-2620 User Manual 11n Preferred: Use the drop-down menu to Enable the 11n Preferred function. The wireless clients with 802.11n protocol will have higher priority to connect to the device. Network Utilization: Set the maximum utilization of this access point for service. The DAP-2620 will not allow any new clients to associate with the AP if the utilization exceeds the value the user specifies. Select a utilization percentage between 100%, 80%, 60%, 40%, 20%, or 0%.
D-Link DAP-2620 User Manual Multi-SSID The device supports up to four multiple Service Set Identifiers. You can set the Primary SSID in the Basic > Wireless section. The SSID’s factory default setting is dlink. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network. Enable Multi-SSID: Check to enable support for multiple SSIDs. Band: Select 2.4GHz or 5GHz. Index: You can select up to seven multi-SSIDs.
D-Link DAP-2620 User Manual Encryption: When you select Open System, toggle between Enable and Disable. If Enable is selected, the Key Type, Key Size, Key Index (1~4), Key, and Confirm Keys must also be configured. Key Type: Select HEX or ASCII. Key Size: Select 64-bit or 128-bit. Key Index (1-4): Select from the 1st to 4th key to be set as the active key. Key: Input up to four keys for encryption. You will select one of these keys in the Key Index drop-down menu.
D-Link DAP-2620 User Manual VLAN VLAN List The DAP-2620 supports VLANs. VLANs can be created with a Name and VID. Mgmt (TCP stack), LAN, Primary/Multiple SSID, and WDS connection can be assigned to VLANs as they are physical ports. Any packet which enters the DAP-2620 without a VLAN tag will have a VLAN tag inserted with a PVID. The VLAN List tab displays the current VLANs. VLAN Status: Use the radio button to toggle to Enable.
D-Link DAP-2620 User Manual Port List The Port List tab displays the current ports. If you want to configure the guest and internal networks on a Virtual LAN (VLAN), the switch and DHCP server you are using must also support VLANs. As a prerequisite step, configure a port on the switch for handling VLAN tagged packets as described in the IEEE 802.1Q standard. VLAN Status: Use the radio button to toggle to Enable. Next, go to the Add/Edit VLAN tab to add or modify an item on the VLAN List tab.
D-Link DAP-2620 User Manual Add/Edit VLAN The Add/Edit VLAN tab is used to configure VLANs. Once you have made the desired changes, click the Save button to let your changes take effect. VLAN Status: Use the radio button to toggle to Enable. VLAN ID: Provide a number between 1 and 4094 for the Internal VLAN. VLAN Name: Enter the VLAN to add or modify.
D-Link DAP-2620 User Manual PVID Settings The PVID Setting tab is used to enable/disable the Port VLAN Identifier Auto Assign Status as well as to configure various types of PVID settings. Click the Save button to let your changes take effect. VLAN Status: Use the radio button to toggle between Enable and Disable. PVID Auto Assign Status: Use the radio button to toggle PVID auto assign status to Enable.
D-Link DAP-2620 User Manual Intrusion The Wireless Intrusion Protection window is used to set APs as All, Valid, Neighborhood, Rogue, and New. Click the Save button to let your changes take effect. Wireless Band: Select 2.4GHz or 5GHz. AP List: The choices include All, Valid, Neighbor, Rogue, and New. Detect: Click this button to initiate a scan of the network.
D-Link DAP-2620 User Manual Schedule The Wireless Schedule Settings window is used to add and modify scheduling rules on the device. Click the Save button to let your changes take effect. Wireless Schedule: Use the drop-down menu to enable the device’s scheduling feature. Name: Enter a name for the new scheduling rule in the field provided. Index: Use the drop-down menu to select the desired SSID. SSID: This read-only field indicates the current SSID in use.
D-Link DAP-2620 User Manual Internal RADIUS Server The DAP-2620 features a built-in RADIUS server. Once you have finished adding a RADIUS account, click the Save button to let your changes take effect. The newly-created account will appear in this RADIUS Account List. The radio buttons allow the user to enable or disable the RADIUS account. Click the icon in the delete column to remove the RADIUS account. We suggest you limit the number of accounts below 30.
D-Link DAP-2620 User Manual ARP Spoofing Prevention The ARP Spoofing Prevention feature allows users to add IP/MAC address mapping to prevent arp spoofing attack. ARP Spoofing Prevention: This check box allows you to enable the arp spoofing prevention function. Gateway IP Address: Enter a gateway IP address. Gateway MAC Address: Enter a gateway MAC address.
D-Link DAP-2620 User Manual Bandwidth Optimization The Bandwidth Optimization window allows the user to manage the bandwidth of the device and arrange the bandwidth for various wireless clients. When the Bandwidth Optimization ruile is finished, click the Add button. To discard the Add Bandwidth Optimization Rule settings, click the Clear button. Click the Save button to let your changes take effect. Enable Bandwidth Optimization: Use the drop-down menu to Enable the Bandwidth Optimization function.
D-Link DAP-2620 User Manual Band: Use the drop-down menu to toggle the wireless band between 2.4GHz and 5GHz. SSID Index: Use the drop-down menu to select the SSID for the specified wireless band. Downlink Speed: Enter the limitation of the downloading speed in either Kbits/sec or Mbits/sec for the rule. Uplink Speed: Enter the limitation of the uploading speed in either Kbits/sec or Mbits/sec for the rule.
D-Link DAP-2620 User Manual AP Array AP Array Scan The AP Array window is used to create up to 32 APs on a local network to be organized into a single group in order to increase ease of management. Click the Save button to let your changes take effect. Central WiFiManager and AP Array are mutually exclusive functions. Enable AP Array: Select the check box to enable the AP array function. The three modes that are available are Master, Backup Master, and Slave.
D-Link DAP-2620 User Manual Configuration Settings In the AP array configuration settings windows, users can specify which settings all the APs in the group will inherit from the master AP. Make the required selection in this window and click the Save button to accept the changes made. Enable AP Array Select to Enable or Disable the AP array configure Configuration: feature here. Wireless Basic Select this option to specify the basic wireless Settings: settings that the APs in the group will inherit.
D-Link DAP-2620 User Manual Wireless Basic Settings Network Name (SSID): Select this option to use the same SSID. SSID Visibility: Select this option to enable SSID visibility. Auto Channel Selection: Select this option to use auto channel selection. Channel Width: Select this option to use the same channel width. Security: Select this option to use the same wireless security. Captive Profile: Select this option to use the same captive profile settings.
D-Link DAP-2620 User Manual Short GI: Select this option to use the same short GI settings. Link Integrity: Select this option to use the same link integrity settings. Connection Limit: Select this option to use the same connection limit value. IGMP Snooping:: Select this option to use the same IGMP snooping settings. Multiple SSID & VLAN SSID: Select this option to use the same multi-SSIDs. SSID Visibility: Select this option to use the same SSID visible.
D-Link DAP-2620 User Manual ARP Spoofing Select this option to use the same ARP spoofing prevention settings. Prevention: Bandwidth Select this option to use the same bandwidth optimization settings. Optimization: Captive Portal: Select this option to use the same captive portal settings. Auto RF: Select this option to use the same auto-RF settings. Load Balance: Select this option to use the same load balancing settings. DHCP Server Settings: Select this option to use the same DHCP server settings.
D-Link DAP-2620 User Manual Auto-RF In this windows, users can view and configure the automatic radio frequency settings as well as configure the the auto-initiate period and threshold values. Click the Save button to accept the changes made. Enable: Auto-RF: Select to Enable or Disable the auto-RF feature here. Initiate Auto-RF: Click the Auto-RF Optimize button to initiate the auto-RF optimization feature. Auto-Initiate: Select the Enable or Disable the auto-initiate feature here.
D-Link DAP-2620 User Manual Load Balance In this window, users can view and configure the AP array’s load balancing settings. Click the Save button to accept the changes made. Enable Load Balance: Select to Enable or Disable the load balance feature here. Active Threshold: Enter the active threshold value here.
D-Link DAP-2620 User Manual Captive Portal Authentication Settings-Web Redirection Only The Captive Portal is a built-in web authentication server. When a station connects to an AP, the web browser will be redirected to a web authentication page. In this window, user can view and configure the Captive Portal settings. After selecting Web Redirection Only as the Authentication Type, we can configure the redirection website URL that will be applied to each wireless client in this network.
D-Link DAP-2620 User Manual IP Address : Subnet Mask : Gateway : DNS : Assign a static IP address that is within the IP address range of your network. Enter the subnet mask. All devices in the network must share the same subnet mask. Enter the IP address of the gateway/router in your network. Enter a DNS server IP address. This is usually the local IP address of your gateway/router.
D-Link DAP-2620 User Manual Authentication Settings- Username/Password The Captive Portal is a built-in web authentication server. When a station connects to an AP, the web browser will be redirected to a web authentication page. In this window, user can view and configure the Captive Portal settings. After selecting Username/Password as the Authentication Type, we can configure the Username/Password authentication that will be applied to each wireless client in this network.
D-Link DAP-2620 User Manual IP (DHCP) is selected, the other fields here will be grayed out. Please allow about 2 minutes for the DHCP client to be functional once this selection is made. IP Address : Assign a static IP address that is within the IP address range of your network. Subnet Mask : Enter the subnet mask. All devices in the network must share the same subnet mask. Gateway : Enter the IP address of the gateway/router in your network. DNS : Enter a DNS server IP address.
D-Link DAP-2620 User Manual Authentication Settings- Passcode The Captive Portal is a built-in web authentication server. When a station connects to an AP, the web browser will be redirected to a web authentication page. In this window, user can view and configure the Captive Portal settings. After selecting Passcode as the Authentication Type, we can configure the Passcode authentication that will be applied to each wireless client in this network. Session Enter the session timeout value here.
D-Link DAP-2620 User Manual grayed out. Please allow about 2 minutes for the DHCP client to be functional once this selection is made. IP Address : Assign a static IP address that is within the IP address range of your network. Subnet Mask : Enter the subnet mask. All devices in the network must share the same subnet mask. Gateway : Enter the IP address of the gateway/router in your network. DNS : Enter a DNS server IP address. This is usually the local IP address of your gateway/router.
D-Link DAP-2620 User Manual Authentication Settings- Remote RADIUS The Captive Portal is a built-in web authentication server. When a station connects to an AP, the web browser will be redirected to a web authentication page. In this window, user can view and configure the Captive Portal settings. After selecting Remote RADIUS as the Authentication Type, we can configure the Remote RADIUS authentication that will be applied to each wireless client in this network.
D-Link DAP-2620 User Manual IP Address : Assign a static IP address that is within the IP address range of your network. Subnet Mask : Enter the subnet mask. All devices in the network must share the same subnet mask. Gateway : Enter the IP address of the gateway/router in your network. DNS : Enter a DNS server IP address. This is usually the local IP address of your gateway/router.
D-Link DAP-2620 User Manual Authentication Settings- LDAP The Captive Portal is a built-in web authentication server. When a station connects to an AP, the web browser will be redirected to a web authentication page. In this window, user can view and configure the Captive Portal settings. After selecting LDAP as the Authentication Type, we can configure the LDAP authentication that will be applied to each wireless client in this network. Session timeout(1-1440) Enter the session timeout value here.
D-Link DAP-2620 User Manual Subnet Mask : Gateway : DNS : Enter the subnet mask. All devices in the network must share the same subnet mask. Enter the IP address of the gateway/router in your network. Enter a DNS server IP address. This is usually the local IP address of your gateway/router. Server: Enter the LDAP server’s IP address or domain name here. Port: Enter the LDAP server’s port number here. Authenticate Mode: Select the authentication mode here. Options to choose from are Simple and TLS.
D-Link DAP-2620 User Manual Authentication Settings- POP3 The Captive Portal is a built-in web authentication server. When a station connects to an AP, the web browser will be redirected to a web authentication page. In this window, user can view and configure the Captive Portal settings. After selecting POP3 as the Authentication Type, we can configure the POP3 authentication that will be applied to each wireless client in this network. Session Enter the session timeout value here.
D-Link DAP-2620 User Manual (DHCP) is selected, the other fields here will be grayed out. Please allow about 2 minutes for the DHCP client to be functional once this selection is made. IP Address : Assign a static IP address that is within the IP address range of your network. Subnet Mask : Enter the subnet mask. All devices in the network must share the same subnet mask. Gateway : Enter the IP address of the gateway/router in your network. DNS : Enter a DNS server IP address.
D-Link DAP-2620 User Manual Login Page Upload In this window, users can upload a custom login web page that will be used by the captive portal feature. Click the Browse button to navigate to the login style, located on the managing computer and then click the Upload button to initiate the upload. Upload Login Style In this field the path to the login style file, that will From Local Hard Drive: be uploaded, will be displayed. Alternatively, the path can be manually entered here.
D-Link DAP-2620 User Manual IP Filter Settings Enter the IP address or network address that will be used in the IP filter rule. For example, an IP address like 192.168.70.66 or a network address like 192.168.70.0. This IP address or network will be inaccessible to wireless clients in this network. Wireless Band : Wireless Band : Select 2.4GHz or 5GHz.
D-Link DAP-2620 User Manual MAC Bypass The DAP-2620 features a wireless MAC Bypass. Once a user is finished with these settings, click the Save button to let the changes take effect. Wireless Band: Select the wireless band for MAC Bypass. SSID Index: Select the SSID for MAC Bypass. MAC Address: Enter each MAC address that you wish to include in your bypass list, and click Add. MAC Address List: When a MAC address is entered, it appears in this list.
D-Link DAP-2620 User Manual DHCP Server Dynamic Pool Settings The DHCP address pool defines the range of the IP address that can be assigned to stations in the network. A Dynamic Pool allows wireless stations to receive an available IP with lease time control. If needed or required in the network, the DAP-2620 is capable of acting as a DHCP server. Function Enable/Disable: Dynamic Host Configuration Protocol (DHCP) assigns dynamic IP addresses to devices on the network.
D-Link DAP-2620 User Manual Static Pool Setting The DHCP address pool defines the range of IP addresses that can be assigned to stations on the network. A static pool allows specific wireless stations to receive a fixed IP without time control. Function Enable/Disable: Dynamic Host Configuration Protocol (DHCP) assigns IP addresses to wireless devices on the network.
D-Link DAP-2620 User Manual Current IP Mapping List This window displays information about the current assigned DHCP dynamic and static IP address pools. This information is available when you enable DHCP server on the AP and assign dynamic and static IP address pools. Current DHCP Dynamic These are IP address pools the DHCP server has Profile: assigned using the dynamic pool setting. Binding MAC Address: The MAC address of a device on the network that is assigned an IP address from the DHCP dynamic pool.
D-Link DAP-2620 User Manual Filters Wireless MAC ACL This page allows the user to configure Wireless MAC ACL settings for access control. Wireless Band: Displays the current wireless band rate. Access Control List: Select Disable to disable the filters function. Select Accept to accept only those devices with MAC addresses in the Access Control List. All other devices not on the list will be rejected. Select Reject to reject the devices with MAC addresses on the Access Control List.
D-Link DAP-2620 User Manual WLAN Partition This page allows the user to configure a WLAN Partition. Wireless Band: Displays the current wireless band. Link Integrity: Select Enable or Disable. If the Ethernet connection between the LAN and the AP is disconnected, enabling this feature will cause the wireless segment associated with the AP to be disassociated from the AP. Ethernet WLAN Access: The default is Enable. When disabled, all data from the Ethernet to associated wireless devices will be blocked.
D-Link DAP-2620 User Manual Traffic Control Uplink/Downlink Setting The uplink/downlink setting allows users to customize the downlink and uplink interfaces including specifying downlink/uplink bandwidth rates in Mbits per second. These values are also used in the QoS and Traffic Manager windows. Once the desired uplink and downlink settings are finished, click the Save button to let your changes take effect. Downlink Bandwidth: The downlink bandwidth in Mbits per second.
D-Link DAP-2620 User Manual QoS Quality of Service (QoS) enhances the experience of using a network by prioritizing the traffic of different applications. The DAP-2620 supports four priority levels. Once the desired QoS settings are finished, click the Save button to let your changes take effect. Enable QoS: Check this box to allow QoS to prioritize traffic. Use the drop-down menus to select the four levels of priority. Click the Save button when you are finished.
D-Link DAP-2620 User Manual Traffic Manager The traffic manager feature allows users to create traffic management rules that specify how to deal with listed client traffic and specify downlink/ uplink speed for new traffic manager rules. Click the Save button to let your changes take effect. Traffic Manager: Use the drop-down menu to Enable the traffic manager feature. Unlisted Client Traffic: Select Deny or Forward to determine how to deal with unlisted client traffic.
D-Link DAP-2620 User Manual Status In the Status Section the user can monitor and view configuration settings of the access point. Here the user can also view statistics about client information, WDS information and more. The following pages will explain settings found in the Status section in more detail.
D-Link DAP-2620 User Manual Device Information This page displays the current information like firmware version, Ethernet and wireless parameters, as well as the information regarding CPU and memory utilization. Device Information: This read-only window displays the configuration settings of the DAP-2620, including the firmware version and the device’s MAC address.
D-Link DAP-2620 User Manual Client Information This page displays the associated clients SSID, MAC, band, authentication method, signal strength, and power saving mode for the DAP-2620 network. Client Information: This window displays the wireless client information for clients currently connected to the DAP-2620. SSID: Displays the SSID of the client. MAC: Displays the MAC address of the client. Band: Displays the wireless band that the client is connected to.
D-Link DAP-2620 User Manual WDS Information Page This page displays the access points SSID, MAC, band, authentication method, signal strength, and status for the DAP-2620’s Wireless Distribution System network. WDS Information: This window displays theWireless Distribution System information for clients currently connected to the DAP-2620. Name: Displays the SSID of the client. MAC: Displays the MAC address of the client. Authentication: Displays the type of authentication being used.
D-Link DAP-2620 User Manual Channel Analyze Wireless Band: Select either 2.4Ghz or 5GHz. Detect: Click the Detect button to scan. AP List: This will list the transmitting channels and quality.
D-Link DAP-2620 User Manual Stats Page Ethernet Traffic Statistics Displays wired interface network traffic information. Ethernet Traffic Statistics: This page displays transmitted and received count statistics for packets and bytes.
D-Link DAP-2620 User Manual WLAN Traffic Statistics Displays throughput, transmitted frame, received frame, and WEP frame error information for the AP network. WLAN Traffic Statistics: This page displays wireless network statistics for data throughput, transmitted and received frames, and frame errors.
D-Link DAP-2620 User Manual Log View Log The AP’s embedded memory holds logs here. The log information includes but is not limited to the following items: cold start AP, upgrading firmware, client associate and disassociate with AP, and web login. The web page holds up to 500 logs. View Log: The AP’s embedded memory displays system and network messages including a time stamp and message type.
D-Link DAP-2620 User Manual Log Settings Enter the log server’s IP address to send the log to that server. Check or uncheck System Activity, Wireless Activity, or Notice to specify what kind of log type you want it to log. Log Server/IP Address: Enter the IP address of the server you would like to send the DAP-2620 log to. Log Type: Check the box for the type of activity you want to log. There are three types: System Activity, Wireless Activity, and Notice.
D-Link DAP-2620 User Manual Maintenance Section In the Status Section the user can monitor and view configuration settings of the access point. Here the user can also view statistics about client information, WDS information and more. The following pages will explain settings found in the maintenance section in more detail.
D-Link DAP-2620 User Manual Administration Limit Administrator Check one or more of the five main categories to display the various hidden administrator parameters and settings displayed on the next five pages. Each of the five main categories display various hidden administrator parameters and settings. Limit Administrator VLAN Check the box provided and the ID: enter the specific VLAN ID that the administrator will be allowed to log in from.
D-Link DAP-2620 User Manual System Name Settings Each of the five main categories display various hidden administrator parameters and settings. System Name: The name of the device. The default name is D-Link DAP-2620. Location: The physical location of the device, e.g. 72nd Floor, D-Link HQ. Login Settings Each of the five main categories display various hidden administrator parameters and settings. User Name: Enter a user name. The default is admin.
D-Link DAP-2620 User Manual SNMP Settings Each of the five main categories display various hidden administrator parameters and settings. Status: Check the box to enable the SNMP functions. This is enabled by default. Public Community String: Enter the public SNMP community string. Private Community String: Enter the private SNMP community string.
D-Link DAP-2620 User Manual Administration Central WiFiManager Settings The Central WiFiManager section is used to create a set of APs on the Internet to be organized into a single group in order to increase ease of management. Central WiFiManager and AP Array are mutually exclusive functions. Enable Central Select to enable or disable the Central WiFiManager: WiFiManager.
D-Link DAP-2620 User Manual Firmware and SSL Upload This page allows the user to perform a firmware upgrade. A Firmware upgrade is a function that upgrade the running software used by the access point. This is a useful feature that prevents future bugs and allows for new features to be added to this product. Please go to your local D-Link website to see if there is a newer version firmware available. Firmware and SSL You can upload files to the access point.
D-Link DAP-2620 User Manual Configuration File Upload This page allows the user to backup and recover the current configuration of the access point in case of a unit failure. Configuration File Upload You can upload and download and Download: configuration files of the access point. Upload Configuration File: Browse to the saved configuration file you have in local drive and click “Open” and “Upload” to update the configuration.
D-Link DAP-2620 User Manual Time and Date Settings Enter the NTP server IP, choose the time zone, and enable or disable daylight saving time. Current Time: Displays the current time and date settings. Enable NTP Server: Check to enable the AP to get system time from an NTP server from the Internet. NTP Server: Enter the NTP server IP address. Time Zone: Use the drop-down menu to select your correct Time Zone. Enable Daylight Check the box to enable Daylight Saving Saving: Time.
D-Link DAP-2620 User Manual Configuration and System These options are the remaining option to choose from in the top menu. Configuration allows the user to save and activate or discard the configurations done. System allows the user to restart the unit, perform a factory reset or clear the language pack settings. Logout allows the user to safely log out from the access point’s web configuration. Help allows the user to read more about the given options to configure without the need to consult the manual.
D-Link DAP-2620 User Manual System Settings On this page the user can restart the unit, perform a factory reset of the access point or clear the added language pack. Restart the Device: Click Restart to restart the DAP-2620. Restore to Factory Default Click Restore to restore the DAP-2620 Settings: back to factory default settings. Clear Language Pack: Click to clear the current Language pack running.
D-Link DAP-2620 User Manual Help The help page is useful to view a brief description of a function available on the access point in case the manual is not present. Help: Scroll down the Help page for topics and explanations.
D-Link DAP-2620 User Manual Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
D-Link DAP-2620 User Manual Registration Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Version 1.
