Specifications

ManualsBrandsD-Link ManualsComputer equipmentAirPlusXtreme G+ DWL-2000AP+

This product can be set up using

any current web browser, i.e.,

Internet Explorer 6 or Netscape

Navigator 6.2.3.

DWL-2000AP+

D-Link

AirPlus

Xtreme

G+

Wireless Access Point

5V 2.5A DC Power Adapter

specifications subject to change without notice. DWL-2000AP+. 002072003

Before You Begin

Check Your Package Contents

DWL-2000AP+ Wireless Access Point

CD-ROM (containing Manual and Warranty)

Ethernet (CAT5 UTP) Cable

If any of the above items are missing, please contact your reseller.

It’s best to use a computer (with an Ethernet adapter) that is connected to a switch for

configuring the DWL-2000AP+. The default IP address for the DWL-2000AP+ is 192.

168.0.50 with a Subnet Mask of 255.255.255.0. You will need to assign your computer

a Static IP address within the same range as the DWL-2000AP+’s IP address for the

purpose of configuring the DWL-2000AP+. See the Appendix if you need assistance

in assigning a Static IP address for your network adapter.

Using a power supply

with a different voltage

rating will damage and void

the warranty of this product.

Summary of content (12 pages)

PAGE 1
DWL-2000AP+ This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.2.3. D-Link AirPlus Xtreme G+TM Wireless Access Point Before You Begin It’s best to use a computer (with an Ethernet adapter) that is connected to a switch for configuring the DWL-2000AP+. The default IP address for the DWL-2000AP+ is 192. 168.0.50 with a Subnet Mask of 255.255.255.0.
PAGE 2
Connecting the DWL-2000AP+ Wireless Access Point to Your Network A. First, connect the power adapter to the receptor at the back panel of the DWL-2000AP+ and then plug the other end of the power adapter to a wall outlet or power strip. The Power LED will turn ON to indicate proper operation. B. Insert one end of the cable to the Ethernet port on the back panel of the DWL-2000AP+ and the other end of the cable to an Ethernet Broadband Router (i.e., D-Link DI-604) or Switch (i.e., D-Link DSS-5+).
PAGE 3
When you have completed the steps in this Quick Installation Guide, your connected network should look similar to this: Using the Setup Wizard Open your Web browserand type “http://192.168.0.50” into the URL address box. Then press the Enter or Return key. The logon pop-up screen will appear. Type “admin” for the username and leave the password field blank.
PAGE 4
Using The Setup Wizard (continued) Once you have logged in, the Home screen will appear. Click Run Wizard You will see the following screens.
PAGE 5
Using The Setup Wizard (continued) Step 1 - Set up your new password. You have the option to establish a password. Click Next Step 2 - Wireless Setup The default wireless settings are: SSID = default Channel = 6 You can change these settings to match an existing wireless network.
PAGE 6
Using The Setup Wizard (continued) Step 3 - Encryption The DWL-2000AP+ is capable of three levels of wireless encryption - 64-bit, 128-bit and 256-bit. By default the encryption is disabled. You can change the encryption settings for more secure wireless communication.
PAGE 7
Click Close You will be returned to the Home tab. Click to Exit For additional settings or information, refer to the Advanced, Tools, or Status tabs on the web-management interface; or to the manual located on the CD-ROM.
PAGE 8
Appendix Assigning a Static IP Address in Windows To assign a Static IP Address to the laptop or computer that you are using to configure the DWL-2000AP+, please do the following: Go to Start > Double- click on Control Panel > Double-click on Network Connections > Right-click on Local Area Connections > Click Properties Highlight Internet Protocol (TCP/IP) Click Properties Select Use the following IP address in the Internet Protocol (TCP/IP) Properties window Input your IP address and subnet mask.
PAGE 9
For Windows 2000 users: Go to Start > Settings > Network and Dial-up Connections > Double-click on the Local Area Connection associated with the Network Adapter installed on your system> select Properties Click Internet Protocol (TCP/IP) Click Properties Select Use the following IP address Input your IP address and subnet mask. (The IP Address must be within the same range as the DWL-2000AP+. The IP Address of the DWL-2000AP+ is 192.168.0.50. You can assign 192.168.0.52 for your computer.
PAGE 10
For Windows Me and 98se users: Click Internet Protocol (TCP/IP) Go to Start > Settings > Control Panel > Double-click on the Local Area Connection associated with the Network Adapter installed on your system > select Properties Click Internet Protocol (TCP/IP) Click Properties Select Specify IP Address Input your IP address and subnet mask. (The IP Address must be within the same range as the DWL-2000AP+. The IP Address of the DWL-2000AP+ is 192.168.0.50. You can assign 192.168.0.52 for your computer.
PAGE 11
For Apple Macintosh OS X: Go to the Apple Menu Click on Network and Select System Preferences Select Built in Ethernet in the Show pull-down menu Select Manually in the Configuration pull-down menu Input your IP address and subnet mask. (The IP Address must be within the same range as the DWL-2000AP+. The IP Address of the DWL-2000AP+ is 192.168.0.50. You can assign 192.168.0.51 for your Macintosh. No two computers can have the same IP Address. Assign a subnet mask of 255.255.255.0.
PAGE 12
Technical Support You can find software updates and user documentation on the D-Link website. D-Link provides free technical support for customers within the United States and within Canada for the duration of the warranty period on this product. U.S. and Canadian customers can contact D-Link technical support through our website, or by phone. Tech Support for customers within the United States: D-Link Technical Support over the Telephone: (877) 453-5465 24 hours a day, seven days a week.