D-Link AirPlus DWL-900AP+ 2.4 GHz Wireless Access Point Manual Rev.
Contents 1. Package Contents ...................................... 3 2. Introduction .................................................. 4 3. Wireless Basics ........................................... 7 4. Getting Started .......................................... 10 5. Using the Configuration Menu .............. 12 6. Using the AirPlus AP Manager.............. 23 7. Troubleshooting ........................................ 27 8. Networking Basics ................................... 32 9.
1. Package Contents Contents of Package: D-Link AirPlus DWL-900AP+ Enhanced 2.4GHz Wireless Access Point Power Supply – 5V DC, 2.0A Manual on CD Quick Installation Guide Ethernet Cable Note: Using a power supply with a different voltage rating than the one included with the DWL-900AP+ will cause damage and void the warranty for this product. If any of the above items are missing, please contact your reseller.
2. Introduction The D-Link AirPlus DWL-900AP+ Wireless Access Point is an enhanced 802.11b high-performance wireless access point. It is an ideal way to extend the reach and number of computers connected to your wireless network. Unlike most 802.11b access points, the DWL-900AP+ is capable of data transfer speeds of up to 22 Mbps (compared to the standard 11 Mbps) when used with other D-Link AirPlus products such as the DWL-520+ Wireless PCI Adapter.
Features & Benefits Up to 2X Faster with AirPlus Products - high-speed wireless data transfer rates up to 22Mbps. With twice the data rate and capacity, the DWL-900AP+ delivers media rich content such as digital images, videos, and MP3 files much faster than standard 802.11b networks Fully 802.11b Compatible – Fully compatible with the IEEE 802.11b standard and interoperable with all existing 802.11b compliant devices Improved Performance – Up to 20% faster data transfer rates on standard 802.
LEDS LED stands for Light-Emitting Diode.
3. Wireless Basics D-Link AirPlus wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link AirPlus wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers.
Wireless Basics Network Expansion - Wireless technology allows the network to go where wires cannot go. Reduced Cost-of-Ownership - While the initial investment required for wireless LAN hardware might be higher than the cost of wired LAN hardware, overall installation expenses and life-cycle costs will be significantly lower. Long-term cost benefits are greatest in dynamic environments requiring frequent moves, adds, and changes.
sense the best possible connection speed to ensure optimal network performance. Installation Considerations Designed to go up to 1,312 feet (400 meters) outdoors and up to 328 feet (100 meters) indoors, D-Link’s AirPlus DWL-900AP+ lets you access your network using a wireless connection from virtually anywhere. Keep in mind, however, that the number, thickness and location of walls, ceilings or other objects that the wireless signals must pass through may limit the range.
4. Getting Started Right out of the box, with its default settings, the DWL-900AP+ will automatically connect with other D-Link Air or AirPlus products. For the price of a single IP Address from your Broadband Internet Service provider you can share the Internet with all the computers on your local network, without sacrificing speed or security, using D-Link AirPlus networking products.
Getting Started Setting Up an Infrastructure Network Please refer to the following sections of this manual for additional information about setting up a network: Networking Basics- learn how to check your IP Address; share printers and files. Using the Configuration Utility- learn the settings you must use on each computer in your network for successful communication.
5. Using the Configuration Menu The Configuration Menu for the DWL-900AP+ is web-based. When using the configuration program, please consider the following: You will need a JavaScript-enabled web-browser such as Internet Explorer 4.0 or higher, or Netscape Navigator 4.0 or higher. The computer that you are using for initial configuration must have an IP Address within the same range as the IP Address of the DWL-900AP+. The DWL-900AP+ has a default IP Address of 192.168.0.50 with subnet mask of 255.255.
Using the Configuration Menu Whenever you want to configure your network or the DWL-900AP+, you can access the Configuration Utility by opening the web-browser and typing in the IP Address of the DWL-900AP+. The DWL-900AP+’s default IP Address is shown below: Open the web browser Type in the IP Address of the Access Point Fig. 5.1 (The IP Address shown in the example above is the default setting.
Using the Configuration Menu AP Name: You may choose to rename your Access Point, especially if you have more than one Access Point on your network. SSID: (Service Set Identifier) “default” is the default setting. The SSID is a unique name that identifies a network. All devices on a network must share the same SSID name in order to communicate on the network. If you choose to change the SSID from the default setting, input your new SSID name in this field. The SSID can be up to 32 characters in length.
Using the Configuration Menu The illustration at right shows the recommended default setting (Disabled) for the DHCP Server function of the DWL-900AP+. If you wish to use the DWL-900AP+ as a DHCP server (not recommended if you already have a DHCP enabled router/gateway on your network) then select Enabled. Enter the IP Address range and click Apply, if you have made any changes. MAC Address Home > DHCP Fig. 5.
Using the Configuration Menu Wireless Client: Will transform any IEEE 802.3 Ethernet device into an 802.11b wireless client as long you are connecting to a DWL-900AP+ acting as an Access Point. The Site Survey function will allow you to scan for available wireless networks. Advanced > Mode > Site Survey Wireless Bridge: This mode will allow you to connect two wireless LANs together. The wireless bridge will only work with another DWL-900AP+.
Using the Configuration Menu Repeater: This mode will allow you to extend the range of your wireless network. The repeater mode will work with another D-Link AirPlus DWL-900AP+, DI-614+, DI-714P+, AirPro DI-764, DI-754 (with inserted DWL-650+), or AirPremier DWL-1000AP+. Note! If you use the DWL-900AP+ in Wireless Client or Repeater Mode, make sure that you enter the Ethernet Mac Address (LAN MAC Address) of the unit that you want to extend the wireless coverage.
Using the Configuration Menu The default Performance settings are shown here. Advanced > Performance Beacon Interval: Beacons are packets sent by an Access Point to synchronize a wireless network. Specify a Beacon interval value. Default (100) is recommended. RTS Threshold: This value should remain at its default setting of 2,432. If you encounter inconsistent data flow, only minor modifications to the value range between 256 and 2,432 are recommended.
network. All devices on a network must use the same SSID to establish communication. Using the Configuration Menu Advanced > Filters Fig. 5.8 Use MAC Filters to allow or deny wireless connection to the DWL900AP+. Select Disable MAC Filters (default) to disable this feature. Select Only allow the MAC address… or Only deny the MAC address… and enter the MAC Address of the selected computer into the field above.
Using the Configuration Menu Tools > System The current system settings can be saved as a file onto the local hard drive by clicking Save. The saved file can be loaded back on the DWL-900AP+ by clicking Browse. When you have selected the settings file, click Load. Click Restore to return to Factory Default Settings. Fig. 5.10 Tools > Firmware Upgrade the firmware for the Access Point. Click on the link to find upgrades to the firmware on the D-Link website at http://support.dlink. com.
Using the Configuration Menu This page displays the current information for the DWL-900AP+. It will display the Ethernet and Wireless information. Ethernet: MAC Address IP Address Subnet Mask Gateway DHCP Server Wireless: MAC Address SSID Encryption Channel AP mode Status > Device Info Fig. 5.12 Status > Log The DWL-900AP+ keeps a running log of events and activities occurring on the Access Point. If the device is rebooted, the logs are automatically cleared.
Using the Configuration Menu Status > Stats Displays the network traffic statistics for both received and transmitted communications through the Ethernet port and wireless connections associated with the Access Point. Fig. 5.14 Status > Wireless Displays the list of computers that are connected to the DWL-900AP+ wirelessly. Fig. 5.
6. Using the AirPlus AP Manager The AirPlus Access Point Manger is a Windows based program to help you manage multiple Access Points in one easy view. Begin the installation by inserting the DWL-900AP+ CD into your CDROM. The AP Manager is also available for download at support.dlink.com. Click Install AirPlus AP Manager The following screen will appear. Click Next Click Next Click Finish to complete installation.
Using the AirPlus AP Manager Link Information The Link Information screen displays the current settings of the selected Access Point AP Settings The AP Settings screen will allow you to change the Access Point settings for the selected Access Point. AP Settings > Advanced Settings The Advanced Settings will allow you to adjust advanced settings for the selected Access Point.
Using the AirPlus AP Manager IP Settings The IP Settings screen will allow you to change the IP Address settings for the selected Access Point. WEP Settings The WEP Settings Screen will allow you to apply Wireless Encryption Protocol to the selected Access Point.
Using the AirPlus AP Manager Firmware Upgrade The Firmware Upgrade screen will allow you to apply new version of the firmware to selected Access Point.
7. Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DWL-900AP+ Wireless Access Point. We cover various aspects of the network setup, including the network adapters. Please read the following if you are having problems. Note: It is recommended that you use an Ethernet connection to configure the DWL-900AP+ Access Point. 1. The computer used to configure the DWL-900AP+ cannot access the Configuration menu.
Troubleshooting 2. The wireless client cannot access the Internet in the Infrastructure mode. Make sure the wireless client is associated and joined with the correct Access Point. To check this connection: Right-click on the Local Area Connection icon in the taskbar> select View Available Wireless Networks. The Connect to Wireless Network screen will appear. Please make sure you have selected the correct available network, as shown in the illustrations below.
Troubleshooting 3. Check that the drivers for the network adapters are installed properly. You may be using different network adapters than those illustrated here, but this procedure will remain the same, regardless of the type of network adapters you are using.
Troubleshooting Double-click on Network Adapters Right-click on D-Link AirPlus DWL-650+ Wireless Cardbus Adapter Select Properties to check that the drivers are installed properly D-Link AirPlus DWL-650 Wireless Cardbus Adapter D-Link AirPlus DWL-650+ Wireless Cardbus Adapter Look under Device Status to check that the device is working properly.
Troubleshooting 4. Resetting the DWL-900AP+ to Factory Default Settings After you have tried other methods for troubleshooting your network, you may choose to Reset the DWL-900AP+ to the factory default settings. Remember that D-Link AirPlus products network together, out of the box, at the factory default settings.
8. Networking Basics Using the Network Setup Wizard in Windows XP In this section you will learn how to establish a network at home or work, using Microsoft Windows XP. Note: Please refer to websites such as http://www.homenethelp.com and http://www.microsoft.com/windows2000 for information about networking computers using Windows 2000, ME or 98. Go to Start>Control Panel>Network Connections Select Set up a home or small office network When this screen appears, Click Next.
Networking Basics Please follow all the instructions in this window: Click Next In the following window, select the best description of your computer. If your computer connects to the Internet through a gateway/router, select the second option as shown.
Networking Basics Enter a Computer description and a Computer name (optional.) Click Next Enter a Workgroup name. All computers on your network should have the same Workgroup name.
Networking Basics Please wait while the Network Setup Wizard applies the changes. When the changes are complete, click Next. Please wait while the Network Setup Wizard configures the computer. This may take a few minutes.
Networking Basics In the window below, select the option that fits your needs. In this example, Create a Network Setup Disk has been selected. You will run this disk on each of the computers on your network. Click Next. Insert a disk into the Floppy Disk Drive, in this case drive A. Format the disk if you wish, and click Next.
Networking Basics Please wait while the Network Setup Wizard copies the files. Please read the information under Here’s how in the screen below. After you complete the Network Setup Wizard you will use the Network Setup Disk to run the Network Setup Wizard once on each of the computers on your network. To continue click Next.
Networking Basics Please read the information on this screen, then click Finish to complete the Network Setup Wizard. The new settings will take effect when you restart the computer. Click Yes to restart the computer. You have completed configuring this computer. Next, you will need to run the Network Setup Disk on all the other computers on your network. After running the Network Setup Disk on all your computers, your new wireless network will be ready to use.
Networking Basics Naming your Computer To name your computer, please follow these directions: In Windows XP: Click Start (in the lower left corner of the screen) Right-click on My Computer Select Properties and click Select the Computer Name Tab in the System Properties window. You may enter a Computer description if you wish, this field is optional.
Networking Basics Naming your Computer In this window, enter the Computer name. Select Workgroup and enter the name of the Workgroup. All computers on your network must have the same Workgroup name.
Networking Basics Checking the IP Address in Windows XP/2000 Type Command Click OK Checking the IP Address in Windows XP/2000 Type ipconfig /all at the prompt. Press Enter. All the configuration settings are displayed as shown below.
Networking Basics Checking the IP Address in Windows XP/2000 Type ipconfig /renew at the prompt to get a new IP Address. Press Enter. The new IP Address is shown below. (Windows 98/ME users: go to Start > Run. Type winipcfg at the prompt. The Windows IP Configuration menu will come up. Click Release, then Renew to obtain a new IP Address.
Networking Basics Assigning a Static IP Address Double-click on Network Connections Right-click on Local Area Connections.
Networking Basics Assigning a Static IP Address Click on Internet Protocol (TCP/IP) Click Properties DWL-650+ Wireless Cardbus Adapter Select Use the following IP address in the Internet Protocol (TCP/IP) Properties window, Input your IP address and subnet mask. (The IP Addresses on your network must be within the same range. For example, if one computer has an IP Address of 192.168.0.2, the other computers should have IP Addresses that are sequential, like 192.168.0.3 and 192.168.0.4.
Networking Basics Assigning a Static IP Address with Macintosh OS X Go to the Apple Menu and select System Preferences. Click on Network Select Built-in Ethernet in the Show pull-down menu. Select Manually in the Configure pull-down menu. Input the Static IP Address, the Subnet Mask and the Router IP Address in the appropriate fields.
Networking Basics Selecting a Dynamic IP Address with Macintosh OS X Go to the Apple Menu and select System Preferences. Click on Network Select Built-in Ethernet in the Show pull-down menu. Select Using DHCP in the Configure pull-down menu. Click Apply Now The IP Address, Subnet mask, and the Router’s IP Address will appear in a few seconds.
Networking Basics Connecting to a Wireless Network in Windows XP To be able to connect to a wireless network, make sure the proper network settings are configured for DWL-650+. Go to Start > right-click on My Network Places > select Properties > double-click on the Wireless Network Connection associated with the DWL-650+ > select Properties > select Internet Protocol (TCP/IP) > click Properties D-Link AirPlus DWL-650+ Wireless Cardbus Adapter Fig. 8.
Networking Basics Connecting to a Wireless Network Connecting to a Wireless Network with a Wireless Router or an Access Point using a static IP address in Windows XP. Select Use the following IP address - if the Wireless Router or Access Point does not have a DHCP server enabled. Input a static IP address within the same range as the Wireless Router or Access Point. IP address: 192.168.0.51 Subnet mask: 255.255.255.
Networking Basics Connecting to a Wireless Network Connecting to a Wireless Network with a Wireless Router or an Access Point using a DHCP server in Windows 2000. Select Obtain an IP address automatically. Select Obtain DNS server address automatically. Click OK Fig 8.30 Connecting to a Wireless Network with a Wireless Router or an Access Point using a static IP address in Windows 2000. Select Use the following IP address Fig. 8.
Networking Basics Connecting to a Wireless Network Connecting to a Wireless Network in Windows Me and 98 Go to Start > Settings > Control Panel > Double-click on the Network associated with the DWL-650+ > Click Properties > Select Internet Protocol (TCP/IP) > Click Properties TCP/IP – D-Link AirPlus DWL-650+ Wireless Cardbus Fig. 8.32 Connecting to a Wireless Network with a Wireless Router or an Access Point using a DHCP server in Windows Me and 98. Select the IP Address tab.
Networking Basics Connecting to a Wireless Network Connecting to a Wireless Network with a Wireless Router or Access Point using a static IP address in Windows Me or Windows 98. Select Specify an IP address. Input a static IP address within the same IP Address range as the wireless router or access point. IP address: 192.168.0.51 Subnet mask: 255.255.255.0 Select Detect connection to network media. Click OK Fig. 8.
Networking Basics Checking the Wireless Connection by Pinging For Windows Me and 98: Go to Start > Run > type command. A window similar to Fig. 9.26 will appear. Type ping xxx.xxx.xxx.xxx, where xxx is the IP address of the Wireless Router or Access Point. A good wireless connection will show four replies from the wireless router or access point, as Fig. 8.36 shown.
Networking Basics Adding a local printer (A printer connected directly to a computer) A printer that is not shared on the network and is connected directly to one computer is called a local printer. If you do not need to share your printer on a network, follow these directions to add the printer to one computer.
Networking Basics Adding a local printer Click Next Select Local printer attached to this computer (Deselect Automatically detect and install my Plug and Play printer if it has been selected.) Click Next Select Use the following port: From the pull-down menu select the correct port for your printer (Most computers use the LPT1: port, as shown in the illustration.
Networking Basics Adding a local printer Select and highlight the correct driver for your printer. Click Next (If the correct driver is not displayed, insert the CD or floppy disk that came with your printer and click Have Disk.) At this screen, you can change the name of the printer (optional.) Click Next Select Yes, to print a test page. A successful printing will confirm that you have chosen the correct driver.
Networking Basics Adding a local printer This screen gives you information about your printer.
Networking Basics Adding a local printer Go to Start> Printers and Faxes A successful installation will display the printer icon as shown at right. You have successfully added a local printer. Sharing a network printer After you have run the Network Setup Wizard on all the computers on your network, you can run the Add Printer Wizard on all the computers on your network.
Networking Basics Sharing a network printer Click on Add a Printer Click Next Select Network Printer Click Next 58
Networking Basics Sharing a network printer Select Browse for a printer Click Next Select the printer you would like to share.
Networking Basics Sharing a network printer To check for proper installation: Go to Start> Printers and Faxes The printer icon will appear at right, indicating proper installation. You have completed adding the printer. To share this printer on your network: Remember the printer name Run the Add Printer Wizard on all the computers on your network. Make sure you have already run the Network Setup Wizard on all the network computers.
Networking Basics Sharing an LPR printer To share an LPR printer (using a print server,) you will need a Print Server such as the DP-101P+. Please make sure that you have run the Network Setup Wizard on all the computers on your network. To share an LPR printer, please follow these directions: Go to Start> Printers and Faxes Click on Add a Printer The screen to the right will display.
Networking Basics Sharing an LPR printer Select Create a new port From the pull-down menu, select Standard TCP/IP Port, as shown. Click Next Please read the instructions on this screen. Click Next Enter the Printer IP Address and the Port Name, as shown.
Networking Basics Sharing an LPR printer In this screen, select Custom. Click Settings Enter the Port Name and the Printer Name or IP Address. Select LPR Enter a Queue Name (if your Print-Server/ Gateway has more than one port, you will need a Queue name.
Networking Basics Sharing an LPR printer This screen will show you information about your printer. Click Finish Select the printer you are adding from the list of Printers. Insert the printer driver disk that came with your printer.
Networking Basics Sharing an LPR printer You can rename your printer if you choose. It is optional. Please remember the name of your printer. You will need this information when you use the Add Printer Wizard on the other computers on your network. Click Next Select Yes, to print a test page. Click Next This screen will display information about your printer. Click Finish to complete the addition of the printer.
Networking Basics Other Tasks For help with other tasks in home or small office networking, see Using the Shared Documents folder and Sharing files and folders in the Help and Support Center in Microsoft Windows XP. 9. Technical Specifications Standards IEEE 802.11b IEEE 802.3 IEEE 802.3u Ports (1) 10/100Base-T Ethernet, RJ-45 (UTP) (1) Power – 5V DC, 2.0A Network Management Web-Based browser with JavaScript Frequency Range 2.4 – 2.
Antenna Type Detachable Reverse SMA Range Indoors – up to 328 feet (100 meters) Outdoors – up to 1,312 feet (400 meters) Temperature Operating: -10ºC to 55ºC (14ºF to 131ºF) Storing: -20ºC to 65ºC (-4ºF to 149ºF) Humidity: 5%-95%, non-condensing Emissions: FCC part 15b UL1950-3
10. Contacting Technical Support You can find the most recent software and user documentation on the D-Link website. D-Link provides free technical support for customers within the United States for the duration of the warranty period on this product. U.S. customers can contact D-Link technical support through our web site, or by phone. D-Link Technical Support over the Telephone: (877) 453-5465 24 hours a day, seven days a week. D-Link Technical Support over the Internet: http://support.dlink.
11. Warranty and Registration D-Link Systems, Inc. (“D-Link”) provides this 3-Year warranty for its product only to the person or entity who originally purchased the product from: D-Link or its authorized reseller or distributor. Products purchased and delivered within the fifty United States, the District of Columbia, US Possessions or Protectorates, US Military Installations, addresses with an APO or FPO.
that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming.
