Specifications

DES-3000 Series Layer 2 Switch CLI Reference Manual
delete cpu access_profile
access_profile command.
Restrictions Only administrator-level users can issue this command.
Example usage:
To delete the CPU access profile with a profile ID of 1:
DES-3026:4#delete cpu access_profile profile_id 1
Command: delete cpu access_profile profile_id 1
Success.
DES-3026:4#
config cpu access_profile
Purpose Used to configure a cpu access profile used for CPU Interface Filtering and to define specific
values that will be used to by the Switch to determine if a given packet should be forwarded or
filtered. Masks entered using the create cpu access_profile command will be combined,
using a logical AND operational method, with the values the Switch finds in the specified frame
header fields. Specific values for the rules are entered using the config cpu access_profile
command, below.
Syntax
config cpu access_profile profile_id <value 1-3> [add access_id <value 1-5> [ethernet
{vlan <vlan_name 32> | source_mac <macaddr> | destination_mac <macaddr> | 802.1p
<value0-7> | ethernet_type <hex 0x0-0xffff>} | ip {vlan <vlan_name 32> | source_ip
<ipaddr> | destination_ip <ipaddr> | dscp <value 0-63> | [icmp {type <value 0-255> code
<value 0-255>} | igmp {type <value 0-255>} | tcp {src_port <value 0-65535> | dst_port
<value 0-65535> | {urg | ack | psh | rst | syn | fin}]} | udp {src_port <value 0-65535> |
dst_port <value 0-65535>} | protocol_id <value 0 - 255> {user_define <hex 0x0-
0xffffffff>}]} | packet_content {offset_0-15 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex
0x0-0xffffffff> <hex 0x0-0xffffffff>| offset_16-31 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff>
<hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_32-47 <hex 0x0-0xffffffff> <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_48-63 <hex 0x0-0xffffffff> <hex
0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_64-79 <hex 0x0-0xffffffff>
<hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff>}] port [<portlist> | all] [permit
| deny] | delete access_id <value 1-5>]
Description
The config cpu access_profile command is used to configure a CPU access profile for CPU
Interface Filtering and to enter specific values that will be combined, using a logical AND
operational method, with masks entered with the create cpu access_profile command,
above.
Parameters
profile_id <value 1-3> − Enter an integer used to identify the access profile that will be
configured with this command. This value is assigned to the access profile when it is created
with the create access_profile command. The profile ID sets the relative priority for the profile
and specifies an index number that will identify the access profile being created with this
command. Priority is set relative to other profiles where the lowest profile ID has the highest
priority.
add access_id <value 1-5> − Adds an additional rule to the above specified access profile.
The value is used to index the rule created.
ethernet − Specifies that the Switch will look only into the layer 2 part of each packet.
• vlan <vlan_name 32> − Specifies that the access profile will apply to only to this VLAN.
• source_mac <macaddr> − Specifies that the access profile will apply to this source MAC
address.
134