D-Link® DGS-1016A DGS-1024A 16/24-Port 10/100/1000Mbps Gigabit Ethernet Switch (Plastic Case) Manual Building Networks for People RECYCLABLE (May 2012) V 1.
D-Link DGS-1016A/DGS-1024A Unmanaged Gigabit Ethernet Switch Information in this document is subject to change without notice. © 2012 D-Link Corporation. All rights reserved. Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden. Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation.
CONTENTS PREFACE……………………………………………………………… IV NOTES, NOTICES, AND CAUTIONS ............................................................IV SAFETY INSTRUCTIONS .............................................................................. V Protecting Against Electrostatic Discharge ..................................... vii INTRODUCTION 8 ABOUT THIS GUIDE ................................................................................... 8 SWITCH DESCRIPTION .....................................................
D-Link DGS-1016A/DGS-1024A Unmanaged Gigabit Ethernet Switch Preface The DGS-1016A/DGS-1024A Manual is divided into sections that describe the system installation and operating instructions with examples. Section 1, Introduction - A description of the physical features of the Switch, including LED indicators, ports and panel descriptions. Section 2, Installation – A description of the physical installation of the Switch, mounting the Switch in a equipment rack and powering on the Switch.
D-Link DGS-1016A/DGS-1024A Unmanaged Gigabit Ethernet Switch Safety Instructions Use the following safety guidelines to ensure your own personal safety and to help protect your system from potential damage. Throughout this safety section, the caution icon ( ) is used to indicate cautions and precautions that you need to review and follow. Safety Cautions To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment, observe the following precautions.
D-Link DGS-1016A/DGS-1024A Unmanaged Gigabit Ethernet Switch Safety Instructions (continued) To help avoid damaging your system, be sure the voltage selection Switch (if provided) on the power supply is set to match the power available at your location: – 115 volts (V)/60 hertz (Hz) in most of North and South America and some Far Eastern countries such as South Korea and Taiwan – 100 V/50 Hz in eastern Japan and 100 V/60 Hz in western Japan.
D-Link DGS-1016A/DGS-1024A Unmanaged Gigabit Ethernet Switch Protecting Against Electrostatic Discharge Static electricity can harm delicate components inside your system. To prevent static damage, discharge static electricity from your body before you touch any of the electronic components, such as the microprocessor. You can do so by periodically touching an unpainted metal surface on the chassis. You can also take the following steps to prevent damage from electrostatic discharge (ESD): 1.
SECTION 1 Introduction About This Guide Switch Description Switch Features D-Link Green Technology Ports Front-Panel Components LED Indicators Power Input on Rear Panel About This Guide Congratulations on your purchase of the DGS-1016A/DGS-1024A 16/24-port 10/100/1000Mbps Gigabit Ethernet Switch. These devices are using compact plastic case and are highly flexible solution for SOHO or small office customers.
Switch Features The DGS-1016A 16-Port and DGS-1024A 24-port Switches do not require any management. Both Switches are designed for easy installation, flexibility and high performance. Connect devices to the Switch as the scale and volume of network traffic increases.
Gigabit Ethernet Technology Gigabit Ethernet is an extension of IEEE 802.3 Ethernet utilizing the same packet structure, format, and support for CSMA/CD protocol, full duplex, flow control, and management objects, but with a tenfold increase in theoretical throughput over 100-Mbps Fast Ethernet and a hundredfold increase over 10-Mbps Ethernet.
periods of low utilization. In addition, the IEEE802.az EEE must be workable when devices at transmit and received side are compliant with IEEE802.3az EEE. D-Link’s innovative EEE+ function can reduce the energy consumption of network links during periods of low utilization even the received device is not compliant with IEEE802.3az EEE. Power Saving Technology: Power saving by link status.
LED Indicators The LED indicators of the Switch include a Power status indicator and Link/Act/Speed indicator for each port. LED Indicators LED Indicator Description Power This lights green while the Switch is receiving power. Link/Act/Speed When connected to a 1000Mbps device, this LED indicator light is green when the port is connected to a device and will blink as data is transmitted or received.
Rear Panel Description The power cable connection is located on the rear panel of the Switch. DC Power Jack: Power is supplied through an external 12V/1A AC power adapter for DGS-1016A and an external 12V/1.5A AC power adapter for DGS1024A. Check the technical specification section for information about the AC power input voltage.
SECTION 2 Installation Package Contents Before You Connect to the Network Installing the Switch Power On Package Contents Open the shipping carton of the Switch and carefully unpack its contents. The carton should contain the following items: One DGS-1016A 16-Port/DGS-1024A 24-Port 10/100/1000BASE-T Gigabit Ethernet Switch One AC power adapter Quick Install Guide Wall-mounting kits If any item is found missing or damaged, please contact your local D-Link reseller for replacement.
Before You Connect to the Network The site where you install the Switch may greatly affect its performance. Please follow these guidelines for setting up the Switch. Install the Switch on a sturdy, level surface that can support at least 3 kg (6.6 lbs.) of weight. Do not place heavy objects on the Switch. The power outlet should be within 1.82 meters (6 feet) of the Switch. Visually inspect the power cord and see that it is fully secured to the AC power port.
Mounting the Switch on a Rack The DGS-1016A/1024A can easily be mounted on a rack. Two mounting ears are provided for this purpose. Make sure that the front panel is exposed in order to view the LEDs. Please refer to the following illustrations: The DGS-1016A/1024A can also be mounted on a wall. Two mounting slots are provided on the bottom of the switch for this purpose. Please make sure that the front panel is exposed in order to view the LEDs. Please refer to the illustration below: A.
Mounting the Switch to a Wall Power On Plug one end of the AC to DC power adapter into the power connector of the Switch and the other end into the local power source outlet. After the Switch is powered on, the LED indicators will momentarily blink. This blinking of the LED indicators represents a reset of the system. Power Failure As a precaution, in the event of a power failure, unplug the Switch. When power is resumed, plug the Switch back in.
Section 3 Connecting the Switch Switch to End Node Switch to Hub or Switch Connecting to a Server NOTE: All Ethernet ports auto-detect MDI/MDIX, port speed (10, 100, 1000Mbps) and duplex of the device connected to the Switch. Cable Quality For all connections to the Switch, use these rules to determine the For connections to 10BASE-T and 100BASE-TX devices, use Category 5 or 5e UTP/STP cable. For connections to 100BASE-TX and 1000BASE-T devices, use Category 5e or better UTP/STP cable.
Connect to an End Node End nodes include PCs outfitted with a 10, 100, or 1000 Mbps RJ-45 Ethernet/Fast Ethernet Network Interface Card (NIC) and most routers. An end node can be connected to the Switch via a twisted-pair Category 3, 4, 5, or 5e UTP/STP cable. The end node can be connected to any of the ports of the Switch.
Connect to Hub or Switch These connections can be accomplished in a number of ways using a standard Ethernet cable. A 10BASE-T hub or switch can be connected to the Switch via a twisted-pair Category 3, 4, 5, or 5e UTP/STP cable. A 100BASE-T hub or switch can be connected to the Switch via a twisted -pair Category 5 or better UTP/STP cable. A 1000BASE-T switch can be connected to the Switch via a twisted -pair Category 5 or better UTP/STP cable.
Connect to Network Backbone or Server Any of the 16/24 Gigabit Ethernet ports are ideal for uplinking to a network backbone or network server.
Appendix Technical Specifications General Standards: IEEE 802.3 10BASE-T IEEE 802.3u compliance IEEE 802.3ab compliance IEEE 802.3x Flow Control supports for Full Duplex Protocol: CSMA/CD Data Transfer Rate: Ethernet: 10Mbps (Half-duplex) 20Mbps (Full-duplex) Fast Ethernet: 100Mbps (Half-duplex) 200Mbps (Full-duplex) Gigabit Ethernet: 2000Mbps (Full-duplex) Topology: Star Network Cables: Ethernet: 2-pair UTP Cat.
Physical and Environmental DC Inputs: Power Consumption: DGS-1016A : AC-DC 12V/1.0A DGS-1024A : AC-DC 12V/1.5A DGS-1016A: 7.89 watts DGS-1024A: 14.17 watts Fan Fan-less Operating Temperature: 32F ~ 104F (0 C ~ 40 ºC) Storage Temperature: 14F ~ 158F (-10C ~ 70C) Humidity: Dimensions (W x D x H) Weight EMI Safety: 5% ~ 90% RH, non-condensing DGS-1016A: 9.1 in x 6.2 in x 1.8 inches (231mm x 158mm x 46mm) DGS-1024A: 10.1 in x 7.0 in x 1.8 inchies (257mm x 178mm x 46mm) DGS-1024A: 0.
Performance Transmission Method: Store-and-forward RAM Buffer: DGS-1016A: 2Mbits per device DGS-1024A: 3.
Glossary 1000BASE-T –1000BASE-T - Known as IEEE 802.3ab which is a standard for Gigabit Ethernet over copper wiring. 100BASE-TX – 100Mbps Ethernet implementation over Category 5 and Type 1 Twisted Pair cabling. 10BASE-T – The IEEE 802.3 specification for Ethernet over Unshielded Twisted Pair (UTP) cabling. aging – The automatic removal of dynamic entries from the Switch Database which have timed-out and are no longer valid. ATM – Asynchronous Transfer Mode.
When two devices transmit simultaneously, a collision occurs and the colliding devices delay their retransmissions for a random amount of time. Data Center Switching – The point of aggregation within a corporate network where a switch provides high-performance access to server farms, a high-speed backbone connection, and a control point for network management and security. Ethernet – A LAN specification developed jointly by Xerox, Intel, and Digital Equipment Corporation.
Rresilient Llink – A pair of ports that can be configured so that one will take over data transmission should the other fail. See also main port and standby port. RJ-45 – Standard 8-wire connectors for IEEE 802.3 10BASE-T networks. RMON – Remote Monitoring. Subset of SNMP MIB II, which allows monitoring and management capabilities by addressing up to ten different groups of information. RPS – Redundant Power System. A device that provides a backup source of power when connected to the Switch.
