6DCM200...
DCM-200 USB/Ethernet Cable Modem Table of Contents
DCM-200 USB/Ethernet Cable Modem Thank you for choosing the D-Link DCM-200 digital, two-way DOCSIS 1.0-compliant USB/Ethernet Cable Modem. The DCM-200 provides customers with high-speed access to the Internet through the cable TV (CATV) network. It works on any cable system that complies with MCNS DOCSIS specifications and provides a high-bandwidth connection to the Internet.
DCM-200 USB/Ethernet Cable Modem You will need to establish an account with your local cable operator in order to access the Internet with this modem. They will assist you in setting up the modem to operate on their network. Then for your modem to communicate with the cable service, you will first need to be able to identify the cable modem. On the cable modem find the make and model (i.e. D-Link DCM-200).
DCM-200 USB/Ethernet Cable Modem In order for you to enjoy the benefits of your Cable Modem, your PC must be properly connected to the cable TV wire. The following diagram illustrates a typical PC/TV installation. (Newer homes or businesses may have a dedicated coaxial cable line for Internet connection). Cable TV Wall Outlet - This is the normal cable TV wall outlet installed by your cable company.
DCM-200 USB/Ethernet Cable Modem This section identifies all the major external components of the device. Both the front and rear panels are shown below followed by a description of each panel feature. The indicator panel is described in detail in the following section. This figure shows the front panel of the device. LED Indicator Panel Refer to the next chapter, “Understanding Indicators,” for detailed information about each of the DCM-200’s LED indicators.
DCM-200 USB/Ethernet Cable Modem The installation of the DCM-200 USB/Ethernet Cable Modem can be completed in a matter of minutes. Be careful to insure the cables are properly locked into position. Follow these steps (see the figure of the rear panel in Identifying External Components): 1. Connect the coaxial TV cable to the DCM-200 jack labeled “CABLE IN.” 2. Connect the external power adapter into the connector labeled “POWER” and the other end to the electrical outlet. 3.
DCM-200 USB/Ethernet Cable Modem Your DCM-200 USB/Ethernet Cable Modem has been designed and manufactured to meet high standards of quality and safety. This section lists important information that will help assure your enjoyment and proper use of the cable modem and accessory equipment. Please read them carefully before operating and using your DCM-200. ♦ Read and Follow Instructions - Read all the operating instructions before operating the modem.
DCM-200 USB/Ethernet Cable Modem If your USB/Ethernet Cable Modem has been properly set up it is unlikely that you should experience any problems with it under normal circumstances. However, we list here some possible solutions to problems that you might experience. Cannot access Internet or e-mail service. Check all connections. • Make sure the cable TV line and the Ethernet (RJ-45) cable is securely connected at all points.
DCM-200 USB/Ethernet Cable Modem ! " " # $ % $ # & & % ! ' $ ( % )) ! '% $ ( * +" , # - ./ 0 ) 1 ./ 2 3 4 2 # .
DCM-200 USB/Ethernet Cable Modem D-Link provides free technical support for customers within the United States. U.S. customers can contact D-Link technical support through our web site, e-mail, or by phone. United States technical support is available Monday through Friday from 6:00 a.m. to 6:00 p.m. (PST). Web: http://www.dlink.com Email: support@dlink.com Phone: 949-790-5290 Thank you for purchasing this product.
DCM-200 USB/Ethernet Cable Modem • The customer is responsible for all shipping charges to and from D-Link (No CODs allowed). Products sent COD will become the property of D-Link Systems, Inc. Products should be fully insured by the customer and shipped to D-Link Systems Inc., 53 Discovery Drive, Irvine CA 92618.
