Data Sheet
Table Of Contents
- CYSBSYS-RP01, Rapid IoT Connect
- General Description
- Key Features
- Package
- Benefits
- Ordering Information
- Contents
- Overview
- Functional Block Diagram
- PSoC 6 MCU
- Dual-band 802.11ac-friendly Radio with BT 5.0
- Crystal and Oscillators
- Chip Antenna for Wi-Fi / BT and u.FL Connector
- CapSense® External Modulation and Integration Capacitors
- Mechanical Dimensions
- Castellated Pads Layout
- Recommended Host PCB Layout
- System Connections
- Castellated Pads Pin Description
- External Reset (XRES)
- Electrical Specifications
- Recommended Operating Conditions
- External ECO Specification
- Environmental Conditions
- ESD and EMI Protection
- Regulatory Information
- Packaging
- Ordering Information
- Part Numbering Convention
- Acronyms
- Document Conventions
- Sales, Solutions, and Legal Information
PRELIMINARY
CYSBSYS-RP01
RF EXPOSURE:
To comply with FCC RF Exposure requirements, the OEM must use the module with on-board chip antenna as-is. The preceding
statement must be included as a CAUTION statement in manuals, for products operating with the approved on-board chip antenna,
to alert users on FCC RF Exposure compliance. Any notification to the end user of installation or removal instructions about the inte
grated radio module is not allowed.
The radiated output power of CYSBSYS-RP01 module is far below the FCC radio frequency exposure limits. End users may not be
provided with the module installation instructions. OEM integrators and end users must be provided with transmitter operating condi
tions for satisfying RF exposure compliance. Nevertheless, the module is to be used in such a manner that the potential for human
contact during normal operation is minimized. This can be accomplished by installing the module as per manufacturer instructions.
The module has been evaluated for and shown compliant with the FCC RF Exposure limits under mobile exposure conditions (ante
nnas are greater than 20cm from a person’s body). This device has also been evaluated for and shown compliant with the FCC RF
exposure limits under portable exposure conditions (antennas are within 20 cm of a person's body) when installed in certain specific
configurations.
ISED
Innovation, Science and Economic Development (ISED) Canada Certification CYSBSYS-RP01 is licensed to meet the regulatory
requirements of Innovation, Science and Economic Development (ISED) Canada. License: IC: 7922A-CYSBSYSRP01.
Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and ensure
compliance for SAR and/or RF exposure limits. Users can obtain Canadian information on RF exposure and compliance from
www.ic.gc.ca.
This device has been designed to operate with the on board chip antenna, having a maximum gain of 1 dBi. The antenna used for
this transmitter must not be co-located or operating in conjunction with any other antennaor transmitter.
ISED NOTICE:
The device CYSBSYS-RP01 including the built-in trace antenna complies with Canada RSS-GEN Rules. The device meets the
requirements for modular transmitter approval as detailed in RSS-GEN. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This device must accept any interference received, including interference that
may cause undesired operation of the device.
Operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile
satellite systems.
L'appareil CYSBSYS-RP01, y compris l'antenne intégrée, est conforme aux Règles RSS-GEN de Canada. L'appareil répond aux ex
igences d'approbation de l'émetteur modulaire tel que décrit dans RSS-GEN. L'opération est soumise aux deux conditionssu
ivantes: (1) Cet appareil ne doit pas causer d'interférences nuisibles, et (2) Cet appareil doit accepter toute interférence reçue, yco
mpris les interférences pouvant entraîner un fonctionnement indésirable.
La bande 5150–5250 MHz est reservee uniquement pour une utilisation a l’interieur afin de reduire les risques de brouillage prejudi
ciable aux systemes de satellites mobiles utilisant les memes canaux.
ISED INTERFERENCE STATEMENT FOR CANADA
This device complies with Innovation, Science and Economic Development (ISED) Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Cet appareil est conforme à la norme sur l'innovation, la science et le développement économique (ISED) norme RSS exempte de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
ISED RADIATION EXPOSURE STATEMENT FOR CANADA
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with a minimum of 7.9 '' (20 cm) distance between the radiation source and your body.
Cet équipement est conforme aux limites d'exposition aux radiations ISED prévues pour un environnement incontrôlé. Cet équipem
ent doit être installé et utilisé avec un minimum de 7,9 po (20 cm) de distance entre la source de rayonnement et votre corps.
Document Number: 002-29368 Rev. *C
Page 16 of 22