Data Sheet
Table Of Contents
- CYSBSYS-RP01, Rapid IoT Connect
- General Description
- Key Features
- Package
- Benefits
- Ordering Information
- Contents
- Overview
- Functional Block Diagram
- PSoC 6 MCU
- Dual-band 802.11ac-friendly Radio with BT 5.0
- Crystal and Oscillators
- Chip Antenna for Wi-Fi / BT and u.FL Connector
- CapSense® External Modulation and Integration Capacitors
- Mechanical Dimensions
- Castellated Pads Layout
- Recommended Host PCB Layout
- System Connections
- Castellated Pads Pin Description
- External Reset (XRES)
- Electrical Specifications
- Recommended Operating Conditions
- External ECO Specification
- Environmental Conditions
- ESD and EMI Protection
- Regulatory Information
- Packaging
- Ordering Information
- Part Numbering Convention
- Acronyms
- Document Conventions
- Sales, Solutions, and Legal Information
PRELIMINARY
CYSBSYS-RP01
Environmental Conditions
This section describes the operating and storage conditions for CYSBSYS-RP01.
Table 13. Enviro nm e ntal Co ndit io ns fo r CYSBSYS-RP01
Description
Minimum Specification
Maximum Specification
Operating temperature
-20 °C
70 °C
Operating humidity (relative, non-condensation)
5 %
85 %
Thermal ramp rate
1 °C/s
3 °C/s
Storage temperature
-40 °C 85 °C
ESD
4kV
8kV
ESD and EMI Protection
Exposed components require special attention to ESD and EMI.
Device Handling: Proper ESD protocol must be followed in manufacturing to ensure component reliability.
Regulatory Information
FCC
FCC NOTICE:
The device CYSBSYS-RP01 complies with Part 15 of the FCC Rules. The device meets the requirements for modular transmitter
approval as detailed in FCC public Notice DA00-1407. Transmitter Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause
undesired operation.
CAUTION:
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by
Cypress Semiconductor may void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates and can radiate radio frequency energy and, if not installed and used in accordance with the instruction may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
■ Consult the dealer or an experienced radio/TV technician for help
LABELING REQUIREMENTS:
The Original Equipment Manufacturer (OEM) must ensure that FCC labeling requirements are met. This includes a clearly visible
label on the outside of the OEM enclosure specifying the appropriate Cypress Semiconductor FCC identifier for this product as well
as the FCC Notice above. The FCC identifier is FCC ID: WAP-CYSBSYS-RP01.
In any case the end product must be labeled exterior with “Contains FCC ID: WAP-CYSBSYS-RP01”.
ANTENNA WARNING:
This device is tested with a standard SMA connector and with the on-board chip antenna. When integrated in the OEMs product,
no rework or replacement is permitted to the on-board chip antenna with higher gain, nor mounting any other external antenna.
Document Number: 002-29368 Rev. *C
Page 15 of 22