Video to PC/HDTV Scaler Operation Manual CSC-220
(1). Introduction Congratulations on your purchase of the Cypress Video Scaler CSC-220. Our professional Video Scaler products have been serving the industry for many years. In addition to Video Scalers, Cypress offers a full line of high quality PC multimedia, Standards Converters, HDMI Switchers, Splitters, Video Mixer, Time Base Correctors, and Video Processors. Please visit www.cypress.com.tw to learn more details about these products. This manual includes operation information on the CSC-220 model.
(4). Controlling the scaler The video scaler is controlled via front panel push buttons or remote control and its status is indicated by OSD display. The front panel controls are shown below. Front Panel 7 8 3 6 5 4 1 2 1. Mode: Press the button repeatedly will toggle through the following adjust controls: Source ResolutionOutput Aspect3D EnhanceDigital NRSources....
2. Picture: Press the button to toggle through picture adjust parameters as follows: ContrastBright Color Hue Detail Contrast * Contrast: Press or to adjust contrast level. The range of adjustment is 0~63. Factory default value is 58. * Bright: Press or to adjust Brightness level. The range of adjustment is 0~63. Factory default value is 31. * Color: Press or to adjust color level. The range of adjustment is 0~63. Factory default value is 31. * Hue: Press or to adjust NTSC Hue level.
7. Power and LED button: Press once to power on the unit, press again to turn it off. Note: * Under picture adjust mode, press and simutaneously will revert the selected parameter back to factory preset value. Press both buttons for over 5 seconds. will revert all picture parameters back to their factory preset values. * You can use RS-232 to lockout the front panel controls.
5 . The HD-15 D-Sub(labeled "RGB/YPbPr") connector is shared by PC/RGBHV output and HDTV/YPbPr output. When PC/RGBHV output resoultion (VGA to SXGA) is selected, use the HD-15 to HD-15 VGA cable to connect the output to the input of your PC monitor. When HDTV/YPbPr output (480p, 576p, 720p, 1080i) is selected, use the HD-15 to YPbPr 3 x RCA cable to connect the output to the YPbPr input of your HDTV display. Note: Use of wrong cable for your selected output will result in an abnormal picture on the screen.
(7). Remote Control 1. POWER: Power ON/OFF button. 2. DISPLAY: Press the button to enable or disable the on screen display of the resolution information. 3. C-VIDEO: Press the button to select composite video as input source. 4. S-VIDEO: Press the button to select S-Video as input source. 5. YCbCr: Press the button to select YCbCr as input source. 6. PC: Press the button to select PC input looping through to the output. 7. VGA: Press the button to select 640 x 480 as output resolution. 8.
(8). RS-232 Control of the CSC-220 Video Scaler The Video Input selection and signal parameter setting for the CSC-220 can also be controlled via an external control system by using the RS-232 port on the unit. If information for this control method is required, beyond the scope of the instructions provided in this section, please contact Cypress Technology Support, A disk is provided with the CSC-220 containing a sample Windows Control Panel that permits remote control of the unit from a PC via RS-232.
(9).
(10). Specifications Computer input (Loop thru) Max computer input resolution Computer input connector type Computer input signal level Video inputs Video standard Video input connectors Scaled output resolutions RGB with HV Sync 1280 x 1024 HD 15 Female RGB @ 0.7V, H&V Sync @ TTL Composite Video @ 1 Vp-p 75 ohm S-Video @ 1 Vp-p 75 ohm YPbPr Y : 1 Vpp 75 ohm PbPr : 0.7 Vp-p 75 ohm NTSC 3.
