Video Scaler Operation Manual
1. Introduction Congratulations on your purchase of the Cypress Video Scaler CSC-1600HD.Our professional video Scaler products have been serving the industry for many years. In addition to VideoScalers, Cypress offers a full line of high quality PC multimedia , Standards Converters, DV-to-Analog Converters,Vieo Mixer, Time Base Correctors, and video processors, Please visit www.cypress.com.tw to learn more details about these products. This manual includes operation information on the CSC-1600HD model.
4. Connecting the hardware The first step is to connect a video source to the input of the Video Scaler and to connect its output to a display device. Below is a photo of the CSC-1600HD rear panel. INPUT SELECT YCbCr C-VIDEO POWER S-VIDEO PC OUTPUT SELECT XGA VGA SVGA 480p/YPbPr 576p/YPbPr 720p SXGA WXGA 1080i 1365X768 ADJUSTMENT ENTER MENU CSC-1600HD VIDEO SCALER R/Pr YPbPr G/Y RGBHV B/Pb OUTPUT H INPUT V HD-15 PC S-VIDEO C-VIDEO Y YCbCr Cb AC 100~240V 50~60Hz Cr RS232 4.
.4 Connecting the AC power CSC-1600HD accepts AC input voltage range from 100~240V (50~60HZ). The unit has a switching power supply installed inside that will convert the AC input to 12V DC 1A. * Power ON/OFF switch-Once the AC power is feed into the unit, the unit enter into standby mode, where a limited current is provided to the micro processor to allow the remote control to work. Press the power on switch will turn the unit on to the normal operation status. 5.
7. Output Selection CSC-1600HD has ten output selection buttons allow you to directly select the desired output resolution. Some output resolution mode may cover more than one horizontal /vertical scanning frequency. This scan rate information will be displayed on the screen when an output selection button is pressed. To alter the scanning rate under a certain output resolution please refer to "ODS menu operation" selection.
8. Picture Adjustment The picture adjustments along with other controls of the scaler can be achieved by using OSD menu control. 9. OSD Menu Operation The MENU, + , - and enter buttons are used in the on screen menu control operation. MENU - This button serves two purposes to show drop-down menu of main menu page and to act as " exit " when an adjustment is complete. Press this button while on main menu page will exit the menu operation.
9. OSD Menu Operation Vertical frequency rate adjust- When it is selected it allows you to choose different vertical frequency while under VGA, SVGA or XGA modes. The higher the vertical refresh rate the less flicker the picture will be. When the vertical refresh rate of an output mode is changed, so will its horizontal scanning rate. please refer to specification page-for cross relationship between vertical and horizontal scanning rate.
11. RS-232 Control of the CSC-1600HD Video Scaler The Video Input selection and signal parameter setting for the CSC-1600HD can also be controlled via an external control system by using the RS-232 port on the unit.
11. RS-232 Control of the CSC-1600HD Video Scaler * Command / Response codes of RS-232 transmission: the Command/ response codes are the combination of 3 bytes. the 1st, 2nd byte are text and the 3rd byte is value.
11. RS-232 Control of the CSC-1600HD Video Scaler * Command / Response codes of RS-232 transmission: the Command/ response codes are the combination of 3 bytes. the 1st, 2nd byte are text and the 3rd byte is value. Video Scaler transimits codes to Remote Controller when scaler operating.
12. Specifications Computer input (Loop thru) Max Computer Input Resolution Computer Input Connector Type Computer Input signal Level RGB with HV Sync 1600 x 1200 HD 15 Female RGB @ 0.7V, H&V Sync @ TTL Composite Video @ 1 Vp-p 75 ohm S-Video @ 1 Vp-p 75 ohm Video Inputs YCbCr Y : 1 Vpp 75 ohm CbCr : 0.7 Vp-p 75 ohm NTSC 3.58, NTSC 4.
