CP-255I Multi-Format to HDMI Scaler Operation Manual
DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document. Cypress also makes no commitment to update or to keep current the information contained in this document.
SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. • To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. • Never spill liquid of any kind on or into this product.
CONTENTS 1. Introduction ���������������������������������������������� 1 2. Applications ��������������������������������������������� 1 3. Package Contents ���������������������������������� 1 4. System Requirements ������������������������������ 1 5. Features ���������������������������������������������������� 2 6. Operation Controls and Functions ��������� 3 6.1 Front Panel �������������������������������������������3 6.2 Rear Panel �������������������������������������������4 6.
1. INTRODUCTION The Multi-Format to HDMI Scaler is designed to upscale digital/analog video signals from Composite, S-Video, PC, Component (HD) and HDMI input sources, to digital HDMI output of a wide range of HDTV and PC resolutions including 1080p and WUXGA (1920 x 1200). As well as upscaling video, the scaler box also converts digital/analog audio signals to digital format, which can then be output either through HDMI combined with the video signal or separately via the discrete Coaxial S/PDIF output.
5. FEATURES • HDMI, HDCP 1.1 and DVI 1.
6. OPERATION CONTROLS AND FUNCTIONS 6.1 Front Panel Digital Video Scaler Processor POWER CV SV COMP PC HDMI MENU 1 2 3 4 - + 5 ENTER 6 1 POWER Button and LED: Press the button power the unit on or off. When the power is turned on, the LED will illuminate. 2 IR Window 3 Input Buttons and LEDs: Press the required button (CV/SV/COMP/ PC/HDMI) to select the desired input source. The LED will illuminate to indicate the corresponding input is selected.
6.2 Rear Panel 3 CO-AX OUT AUX IN 6 RS-232 PC IN R L CO-AX 8 R CV L DC 5V PC IN HDMI OUT HDMI IN Cr/Pr 1 2 4 Cb/Pb 5 Y R L SV 7 9 1 HDMI OUT and COAX OUT: Connect the HDMI OUT port to an HDMI display such as HDTV or monitor. Connect the COAXIAL OUT port (TOSLINK) to an amplifier for separate digital audio output.
8 Composite Video IN and L/R IN: Connect the Composite Video input port to source equipment such as a DVD player or Set-top box for video signal conversion. Connect the L/R audio input ports to source equipment for audio signal conversion. 9 DC 5V: Plug the 5 V DC power supply into the unit and connect the adaptor to AC wall outlet. 6.3 Remote Control 1 POWER: Press the button once to power on the unit. Press again to enter standby mode.
6.
MAIN MENU SUBMENU ADJUSTMNET AUDIO SOURCE HDMI, L/R, COAXIAL DELAY OFF, 40ms, 110ms, 150ms SOUND ON, MUTE EXIT - - SOURCE (Input interface) INFORMATION INPUT (Input resolution) OUTPUT (Output resolution) VERSION (Firmware version) EXIT - - Note: Items in brackets are the default values for those settings. 6.
6.
COMMAND RESPONSE DESCRIPTION S OUTPUT 11 OUTPUT 576I Set the output resolution to 576i@60 Hz S OUTPUT 12 OUTPUT 576P Set the output resolution to 576p@60 Hz S OUTPUT 13 OUTPUT 720P Set the output resolution to 720p@50 Hz S OUTPUT 14 OUTPUT 1080I50 Set the output resolution to 1080i@50 Hz S OUTPUT 15 OUTPUT 1080P50 Set the output resolution to 1080p@50 Hz S OUTPUT 16 OUTPUT WXGA Set the output resolution to WXGA resolution S OUTPUT 17 OUTPUT WSXGA Set the output resolution to WSXGA S
COMMAND RESPONSE DESCRIPTION S BRIGHTNESS 0~100 BRIGHTNESS 0~100 (45) Adjust the BRIGHTNESS value S HUE 0~100 HUE 0~100 (50) Adjust the HUE value S SATURATION 0~100 SATURATION 0~100 (60) Adjust the SATURATION value S SHARPNESS 0~100 SHARPNESS 0~100 (32) Adjust the SHARPNESS value S NR 0 NR OFF~HIGH Set the noise reduction to OFF S NR 1 NR LOW Set the noise reduction to LOW S NR 2 NR MIDDLE Set the noise reduction to MIDDLE S NR 3 NR HIGH Set the noise reduction to HIGH S PCHPOSITI
COMMAND RESPONSE DESCRIPTION S BLUE 0~100 BLUE 0~100 (47) Adjust the value for the BLUE color setting S OSDHPOSITION 0~100 OSDHPOSITION 0~100 (50) Set the value to adjust the horizontal position of the OSD menu S OSDVPOSITION 0~100 OSDVPOSITION 0~100 (50) Set the value to adjust the vertical position of the OSD menu S OSDTIMEOUT 0~100 OSDTIMEOUT 0~100 (10) Set the value for the OSD menu timeout S OSDBACKGROUND 0~8 OSDBACKGROUND 0~8 (5) Set the value for the OSD menu background S AUDIOMUTE
6.
COMMAND RESPONSE DESCRIPTION R BLUE BLUE 0~100 Reports the value (1~100) of the RED color setting R OSDHPOSITION OSDHPOSITION 0~100 Reports the value (1~100) of the OSD MENU horizontal position setting R OSDVPOSITION OSDVPOSITION 0~100 Reports the value (1~100) of the OSD MENU horizontal position setting R OSDTIMEOUT OSDTIMEOUT 0~100 Reports the value (1~100) of the OSD MENU TIMEOUT setting R OSDBACKGROUND OSDBACKGROUND 0~8 Reports the value (1~8) of the OSD MENU BACKGROUND setting R AUDIO
6.
7. CONNECTION DIAGRAM Composite Video, Coaxial Digital Audio and Analog Stereo Audio Input RS-232 Control from PC/Laptop or RS-232 Control System RS-232 DVD player DP.BY!PVU BVY!JO ST.343 QD!JO S M DP.
8. SPECIFICATIONS Video Bandwidth 1.65 Gbps (Single-link) Input Ports 1×HDMI, 1×VGA (D-sub 15-pin), 1×Component Video(3 RCA), 1×Composite Video, 1×S-Video, 1×Coaxial (TSOLINK), 2×3.
9.
CYPRESS TECHNOLOGY CO., LTD Home page: http://www.cypress.com.
