Specifications
Graphics Controller
Maximum Dot Clock
Horizontal Scan Rates
Display Memory
Display Colors
Graphics Output
BIOS PROM
PMC/PCI Bus Interface
XMC/PCIe Bus Interface
USB Host Controller
Video/Audio Digitizer
RGBHV/DVI/YUV Digitizer
MIPI CSI-2 Digitizer
Power Requirements
Environment
Temperature
Humidity
PMC/XMC Mechanical
Dimensions
Front Panel I/O Connectors
Analog Monitor Support
Digital Monitor Support
Maintenance Features
AMD Radeon E4690 (AKA M96 CSP or RV730, PCI Dev ID 9491)
400 MHz
31.5 to 115 KHz
512 MB DDR3
16.7 Million @ 24-bits
Standard output is 2x DisplayPort using Mini DisplayPort connectors. See note on Page 4 about power.
64Kb Serial EEPROM stores power-up configuration (BIOS). Optional secondary BIOS EEPROM.
Pericom PI7C9X130 32/64-bit, 33-133 MHz PCI/PCI-X to PCIe 1.1 x4 Bridge
Supports Universal PCI Bus signaling (5V and 3.3V) on the PMC side.
IDT 89HPES24T6G2 6 port PCIe 2.0 PCIe switch; each port is x4 PCIe lanes.
Ports 0&1: connected to XMC, x4 or x8, PCIe 2.0; (power save option: x4 only)
Ports 2&3: connected to E4690, x4 or x8, PCIe 2.0; (power save option: x4 only)
Port 4: connected to uPD720201, x1, PCIe 2.0;
Port 5: connected to CX25858, x1, PCIe 1.1
Renesas uPD720201, four port, USB 3.0/2.0 compliant, switched power control (see note on Page 4 about
power). 64Kb Serial EEPROM stores power-up configuration. Port assignment allocates:
Port 1 to STM32F427 BIST controller;
Port 2 to Cypress CX3 USB 3.0-based MIPI CSI-2 camera controller;
Port 3 to user XMC rear I/O;
Port 4 to Cypress FX3 USB 3.0-based Peripheral Controller (interfaced to ADV7441A)
Conexant CX25858, 8 NTSC/PAL Composite Video In, 8 Audio In (standard Agate connects 4), all channels
can be active at once. Video capture mode is 4:2:2 or 4:1:1, choice of NTSC or PAL affects all inputs; pairs of
audio inputs can be configured for stereo. 2Kb Serial EEPROM stores power-up configuration.
Analog Devices ADV7441A captures RGBHV (SOG or separate sync) or DVI (not simultaneously),
1600x1200x16bpp; interfaces to Cypress FX3 USB 3.0 Peripheral Controller and uses modified Cypress
video input application software. Front panel supports RGBHV in only. Rear I/O supports RGBHV or DVI.
The ADV7441A output can be disabled and an 8-bit YUV camera can be connected via a mid-board connec-
tor to drive the FX3.
Cypress CX3 USB 3.0 based controller for MIPI CSI-2 1-4 lanes captures high resolution camera input.
AgatePXC can easily exceed the nominal power limits of PMC (7.5W). XMC really has no limits, being con-
trolled by the amount of available cooling and host power supply capabilities. In order to achieve full operabili-
ty, the AgatePXC/2 requires host power as follows:
Host Bus Voltage Input Idle Full Operation
PMC/XMC 3.3V 0.5A 2A
PMC 5V 1.75A 6.85A
XMC VPWR=5V 1.75A 6.85A
VPWR=12V 1.1A 3A
0°C to +70°C, operating; -55°C to +85°C, storage
5% - 95% non-condensing
IEEE 1386-2001 [except Side 2 max component height is approx. 3.1 mm instead of 2.1 mm. This is not a
significant issue.]
149 mm x 74 mm
AgatePXC/1V: Dual VGA
AgatePXC/1D: Dual Mini DisplayPort (mDP)
AgatePXC/1L: Honda SDR26
AgatePXC/2: 2x mDP + Honda SDR50
Dual, VGA or RGB w/SOG, up to 1920x1200@24 bpp, interlaced/non-interlaced. Ch 2 also supports a variety
of composite, HDTV, NTSC, and PAL formats.
Dual, DisplayPort 1.1a, up to 2560x1600
See Page 10
SSppeecciiffiiccaattiioonnss
NNoonn-ssttaannddaarrdd
VVeerrssiioonnss
If you have special configuration requirements that do not appear to be covered by the standard versions, please contact
the sales department for assistance.
page
13