User's Manual
Table Of Contents
- General Description
- Benefits
- Overview
- Pad Connection Interface
- Recommended Host PCB Layout
- Module Connections
- Bluetooth Baseband Core
- Power Management Unit
- Microprocessor Unit
- Integrated Radio Transceiver
- Peripheral Transport Unit
- ADC Port
- PWM
- Triac Control
- Security Engine
- Electrical Characteristics
- RF Specifications
- Timing and AC Characteristics
- Environmental Specifications
- Regulatory Information
- Packaging
- Ordering Information
- Acronyms
- Document Conventions
- Document History Page
- Sales, Solutions, and Legal Information
Document Number: 002-19043 Rev. PRELIMINARY Page 26 of 33
PRELIMINARY
CYBLE-413136-01
Innovation, Science and Economic Development (ISED) Canada Certification
CYBLE-413136-01 is licensed to meet the regulatory requirements of Innovation, Science and Economic Development (ISED)
Canada.
License: IC: 7922A-3136
Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and ensure
compliance for SAR and/or RF exposure limits. Users can obtain Canadian information on RF exposure and compliance from
www.ic.gc.ca.
This device has been designed to operate with the antennas listed in Table 5 on page 9, having a maximum gain of -0.5 dBi. Antennas
not included in Table 5 on page 9 or having a gain greater than -0.5 dBi are strictly prohibited for use with this device. The required
antenna impedance is 50 ohms. The antenna used for this transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
ISED NOTICE:
The device CYBLE-413136-01 including the built-in trace antenna complies with Canada RSS-GEN Rules. The device meets the
requirements for modular transmitter approval as detailed in RSS-GEN. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This device must accept any interference received, including interference that
may cause undesired operation.
L'appareil CYBLE-413136-01, y compris l'antenne intégrée, est conforme aux Règles RSS-GEN de Canada. L'appareil répond aux
exigences d'approbation de l'émetteur modulaire tel que décrit dans RSS-GEN. L'opération est soumise aux deux conditions
suivantes: (1) Cet appareil ne doit pas causer d'interférences nuisibles, et (2) Cet appareil doit accepter toute interférence reçue, y
compris les interférences pouvant entraîner un fonctionnement indésirable.
ISED INTERFERENCE STATEMENT FOR CANADA
This device complies with Innovation, Science and Economic Development (ISED) Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Cet appareil est conforme à la norme sur l'innovation, la science et le développement économique (ISED) norme RSS exempte de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonction-
nement.
ISED RADIATION EXPOSURE STATEMENT FOR CANADA
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with a minimum distance 15mm between the radiator and the operator.
Cet équipement est conforme aux limites d'exposition aux radiations ISED prévues pour un environnement incontrôlé. Cet équipement
doit être installé et utilisé avec une distance minimale de 15 mm entre le radiateur et l'opérateur.
LABELING REQUIREMENTS:
The Original Equipment Manufacturer (OEM) must ensure that ISED labelling requirements are met. This includes a clearly visible
label on the outside of the OEM enclosure specifying the appropriate Cypress Semiconductor ISED identifier for this product as well
as the ISED Notice above. The IC identifier is 7922A-3136. In any case, the end product must be labeled in its exterior with
"Contains IC: 7922A-3136".
Le fabricant d'équipement d'origine (OEM) doit s'assurer que les exigences d'étiquetage ISED sont respectées. Cela comprend une
étiquette clairement visible à l'extérieur de l'enceinte OEM, en précisant l'identifiant Cypress Semiconductor approprié pour ce produit
ainsi que l'avis ISED ci-dessus. L'identifiant ID est 7922A-3136. En tout cas, le produit final doit être étiqueté dans son extérieur avec
"Contient IC: 7922A-3136".