User's Manual

CYBLE-01201x-x0
Document Number: 002-02521 Rev. ** Page 12 of 31
Electrical Specification
Tab le 7 details the absolute maximum electrical characteristics for the Cypress BLE module.
Table 7. CYBLE-01201x-x0 Absolute Maximum Ratings
Tab le 8 details the RF characteristics for the Cypress BLE module.
Table 8. CYBLE-01201x-x0 RF Performance Characteristics
Tab le 9 through Table 48 list the module level electrical characteristics for the CYBLE-01201x-x0. All specifications are valid for –40
°C ≤ TA ≤ 85 °C and TJ ≤ 100 °C, except where noted. Specifications are valid for 1.71 V to 5.5 V, except where noted.
Parameter Description Min Typ Max Units Details/Conditions
V
DDD_ABS
Analog, digital, or radio supply relative to V
SS
(V
SSD
= V
SSA
)
–0.5 – 6 V Absolute maximum
V
CCD_ABS
Direct digital core voltage input relative to V
SSD
–0.5 – 1.95 V Absolute maximum
V
DD_RIPPLE
Maximum power supply ripple for V
DD
and V
DDR
input voltage
– – 100 mV
3.0V supply
Ripple frequency of 100 kHz
to 750 kHz
V
GPIO_ABS
GPIO voltage –0.5 – VDD +0.5 V Absolute maximum
I
GPIO_ABS
Maximum current per GPIO –25 – 25 mA Absolute maximum
I
GPIO_injection
GPIO injection current: Maximum for V
IH
> V
DD
and minimum for V
IL
< V
SS
–0.5 – 0.5 mA
Absolute maximum current
injected per pin
LU Pin current for latch up –200 200 mA –
Parameter Description Min Typ Max Units Details/Conditions
RF
O
RF output power on ANT –18 0 3 dBm
Configurable via register
settings
RX
S
RF receive sensitivity on ANT – –91 – dBm
Guaranteed by design
simulation; High Gain Mode
F
R
Module frequency range 2400 – 2480 MHz –
G
P
Peak gain – 0.5 – dBi –
G
Avg
Average gain – –0.5 – dBi –
RL Return loss – –10.5 – dB –
Table 9. CYBLE-01201x-x0 DC Specifications
Parameter Description Min Typ Max Units Details/Conditions
V
DD1
Power supply input voltage 1.8 – 5.5 V With regulator enabled
V
DD2
Power supply input voltage unregulated 1.71 1.8 1.89 V
Internally unregulated
supply
V
DDR1
Radio supply voltage (radio on) 1.9 – 5.5 V –
V
DDR2
Radio supply voltage (radio off) 1.71 – 5.5 V –
Active Mode, V
DD
= 1.71 V to 5.5 V
I
DD3
Execute from flash; CPU at 3 MHz – 1.7 – mA
T = 25 °C,
V
DD
= 3.3 V
I
DD4
Execute from flash; CPU at 3 MHz – – – mA T = –40 °C to 85 °C
I
DD5
Execute from flash; CPU at 6 MHz – 2.5 – mA
T = 25 °C,
V
DD
= 3.3 V
I
DD6
Execute from flash; CPU at 6 MHz – – – mA T = –40 °C to 85 °C
I
DD7
Execute from flash; CPU at 12 MHz – 4 – mA
T = 25 °C,
V
DD
= 3.3 V