User manual

Email your order to us at [e-mail]
24
IR Distribution
Standard IR Receiver 40kHz suitable for most
domestic AV equipment.
Standard IR Receiver
Code IRSR £ 12.99
Wide Band IR Receiver Up to 100kHz – for more
esoteric equipment.
Wideband IR Receiver
Code IRWBR £ 18.99
This IR receiver is designed to be affixed directly to the
fascia on your display. Super fast electronics and a
semi-wideband capability make it really effective to use
whilst it’s compact size makes it very unobtrusive. The
LED provides visual confirmation that the signal has
been received. Typical IR receivers require a minimum
of 10 cycles before they can “lock” onto the signal.
This receiver will work with just 3 or 4 cycles. This fast
circuitry enables it to work with set top boxes that use
very short bursts of IR code (known as RCMM code), as
used for example by some BT Vision set top boxes.
Fascia Mount IR Receiver
Code IRFMR £ 14.99
IRSR built into a single gang pattress with translucent
finish flush wall plate
Wall Plate IR Receiver
Code IRSP £ 24.99
An Infra Red panel mount receiver designed to be used
with any Keene IR Distribution amplifier. This receiver
can be fitted into the cabinet casing or studded wall.
• Requires a 16mm diameter hole
• Overall thread length 44mm
• Maximum material thickness 38mm
• Visible bezel diameter 30mm
• Connection is via a 1m cable to 3.5mm jack plug
Code IRPMR black £29.99
Code IRPMRW white £29.99
Code IRPMRB brass £34.99
Code IRPMRC chrome £34.99
Panel Mount IR Receivers
The Universal wand is ideal for most applications and
can be mounted directly onto the equipment fascia or
placed on the shelf in front. Dimensions of emitter:
L 21mm x W 19mm x D 7mm. Fitted with a 1.2
metre cable.
IR Universal Wand
Code IRUW £ 5.99
This is a small discrete emitter that can be mounted
directly onto the device's fascia by means of a small
sticky pad. A small red LED 'blinks' each time an IR
signal is emitted as confirmation that the command
has been sent. Dimensions of emitter: L x 10mm x W
10mm x D 5mm. Fitted with a 3 metre cable.
IR Single Blinking Wand
Code IRBW £ 9.49
The single jack plug drives two IR emitter wands. The
emitters are extremely tiny (just 9mm across) and are
supplied with double sided adhesive pads to affix
directly to the equipment fascia. The emitters actually
flash red as the IR signal is emitted giving visual
confirmation that the IR signal was received and
transmitted correctly.
IR Dual Blinking Wand
Code IRDW £ 9.99
Can be attached directly to the equipment facia or will
work up to 4 metres away. Even when attached directly
the equipment will still respond to external IR signals.
For use with the RBKIT low power output sockets.
IR Low Power Wand
Code IRLPW £ 5.99
Only for use with the Keene IRBKIT in the "High Power"
output socket. Provides a very high output IR signal
that will operate equipment up to 10 metres away. If
placed inside a cabinet the signal will usually reflect to
operate several items of equipment without requiring
any other emitters. It can also be used with other
Keene IR Distribution amplifers or the IRBKIT low power
socket but will then only perform as a low power
emitter. Not suitable for one-to-one operation.
IR High Power Wand
Code IRHPW £ 7.99
A short range emitter for direct attachment to the
equipment fascia. Low profile design ideal for use in
tight spaces. Dimensions of emitter: L x 25mm x W
9mm x D 6mm Fitted with a 1.2 metre cable.
Side Firing Wand
Code IRSFW £ 7.99
Keene IR Receiver Adaptor
KRECA
This device allows Keene IR receivers to be used with other
manufacturers IR distribution systems, for example Xantech,
Onkyo, Harmon Kardon etc. The design allows a number of
parameters to be changed including:
Data (5v or 12v) and Carrier signal (exclude / include).
Supplied complete with a 3.5mm jack to jack 1.2m link cable.
Code KRECA £ 39.99
Anything To Keene IR
Translator KIRT
The Keene IR Translator is designed to allow you to connect
the IR wand output from any device directly into the IR
receiver input of any Keene
IR equipment, such as an
IRBKIT, IRCM, IR Anywhere
module etc. This is
particularly useful with
HDMI video over distance
systems as the single IR
wand output is usually
insufficient for effective control of multiple sources. The 3
pole input connector is optically coupled and will work with
any connection as positive or negative. Compatible with IR
frequencies between 10Khz - 200KHz.
Code KIRT £19.99
Also available KIRT12 for non-keene 12v based IR
systems £19.99
Keene IR Emitter Shield. A
soft flexible rubber cover
that will prevent unwanted
IR cross talk.
Can be used with all Keene
and most other
manufacturers IR Emitters
* Improves IR Signal to
noise ratio
* Prevents IR signals from interfering with other
equipment
Overall dimensions 37mm x 29mm
Internal space for emitter 27mm x 14mm (widest) x
7.5mm (deepest)
IR Emitter Shield
Code IRSHIELD £ 3.49
Code IRSHIELD4 £ 9.99
Code IRSHIELD10 £ 19.99
Single IR Shield
Pack of Four IR Shields
Pack of Ten IR Shields
117657_Connections_October_2014.indd 24 16/10/2014 11:21