User manual

Email your order to us at [e-mail]
16
HDMI Over Long Distances
HDMI over IP Network
As well as HDMI over (dedicated) Cat5 cable we can now
offer transmitter / receiver systems that will send HDMI
signals via an IP computer network. Amazingly they place
very little load on your network bandwidth and operate as a
true multicast - that is to say one transmitter can drive
multiple receivers with no extra network load! They really
are extremely simple to operate, just plug and play with no
in-depth networking capability required. They also provide
full IR feedback allowing remote control of source
equipment. A flexible, scalable, low cost solution to
distributing HD signals to multiple displays. They can be
used in Extender Mode (connect the Sender to the Receiver
by CAT5e/6/7 cable directly) or Broadcaster
Mode (Sender to Receiver via LAN) for one Sender to
many Receivers.
The newly updated PB5000Plus units now provide IR
feedback and RS232 control
and deliver stunning Ultra High Quality 1080p HDMI Video
broadcast over IP network.
Via an inexpensive Gigabit Ethernet network switch the
PB5000P can support Point to Point, Point to Many
Broadcasting, and Multi-Casting which multiple video
sources with PB5000+ Senders video streaming to multiple
TVs/Displays/Projectors with PB5000+ Receiver. Multi-
casting can be done by Managed Gigabit Switch with
802.1Q VLAN function which provide control remotely and
allows more video source/senders to be integrated.
Code PB5000P Sender/Receiver pair £524.54
Code PB5000PR Additional receiver £394.62
Yet another really useful way to get HDMI from one place
to another, the PCE122 can send ultra high quality HDMI
v1.3 over a single coaxial cable! (RG6 or RG59). It can
send full HD 1080P up to 120M or 720P up to 230M,
both with full 7.1 channel audio. The conversion is fully
digital (HDMI to SDI and back again) with no additional
compression and gives you crystal clear HD at long
distances. The PCE122 also contains a built-in 1 to 2
Coaxial Splitter to drive two separate receivers and each
receiver has a loop-through
to daisy chain
additional receivers as
required. Cables are
connected via BNC for
a secure, vibration
resistant connection.
Specifications:
• 120M HDMI 1080p video and 7.1channel audio one
cable transmission with Ultra High Quality Video
• Features World Leading Single Coaxial Transmission,
designed to simplify Installation
• 1080p 120M / 720p 230M long distance Ultra
High Quality Video with 7.1 channels surround
sound transmission
• Up to 7.1 channels audio, Dolby® Digital / Dolby®
TruHD/DTS®-HD pass-thru
• Built-in 1 to 2 Coaxial Splitter in Sender and One
Coaxial Cascade output in Receiver for great extension
flexibility
• Support 5 layers Cascadable for up to 600M 1080p
video transmission and up to 10 TVs/Displays/
Projectors connected
• BNC connector designed for solid coaxial connection
• HDMI v1.3b, HDCP Compliant
• Hassle free plug-n-play, install in seconds
PCE122 with IR feedback:
Code PCE122IR (transmitter & receiver pair with IR) £542.61
Code PCE122RIR (additional receiver with IR) £315.70
HDMI over Single Coaxial Extender
Code DMHD01 £ 949.00
HDMI DVB-T Digital RF
Modulator
Use your existing RF aerial cables to distribute HD signals
around your house. Simply connect your HD source (eg
Sky) to the modulator and tune your HD tv's into your new
modulators Freeview channel. The Conexer DMHD01 HDMI
DVB-T modulator generates a digital high definition channel
from an HDMI source which can be supplied over a coaxial
cable network to digital TV sets or STB's in the system.
Compatible with all Freeview™ HD TV sets & STB's, the
modulator is also compatible with standard Freeview™ TV
sets which support H.264. Perfect for distributing a SkyHD,
Virgin Tivo, BluRay Player, PC, CCTV etc around the home or
office to all TVs connected to your existing RF aerial
distribution system
Not only that, the modulated HD channel is also streamed
via IP, so if you connect your DMHD01 to your router you
will be able to watch whatever is being modulated as a
stream direct to your phone or tablet.
Features:
• DMHD01 converts HDMI A/V signals into a High
Definition DVB-T multiplex
• Fully programmable via front panel LCD
• LCN function (logical channel numbering allowing user
defined EPG location),
• UHF/VHF Band (47-862MHz)
• DVB-T
• 2K or 8K carrier
• DVB-T or DVB-C
• IP streamer
HDMI over CAT5E/5 Extender
The Coosis HDMI Extender over CAT6 extends HDMI at up
to 1080P up to 50m over a single CAT5E/6 cable.
Both the sender & receiver support two way IR transmision
for full control (one IR receiver and one IR emitter are
included in the pack, and an additional IR receiver and IR
emitter set can be purchased separately (order code CIRSET)
for the two-way feature.
The HECAT6ARC has two distance modes to work at either
0-20m or 20-50m. This switching ensures the most reliable
results by avoiding the application of too much gain when
it is not required.
Sender input: 1 x HDMI type A 19pin female
Sender Output: 1 x RJ45
Receiver input: 1 x RJ45
Receiver output: 1 x HDMI type A 19pin female
In/Out resolutions: 480i/P, 720P, 1080i/P@60
Audio support: LCPM, AC-3, DTS 7.1, DSD
Power: 5v DC 1000mA, UK adaptor supplied
Dimensions (sender & receiver) 80 x 49 x 25mm
Code HECAT6S50 £ 79.99
HDMI over Mains Wiring
At last – send an HDMI signal from one place to another
without having to run any extra cables. Simply connect your
HDMI sources (up to two) to the sender and plug it into the
mains. Next take the receiver to the room you want to view in,
connect the HDMI output to your display and plug it onto the
mains. That's all there is to do, apart from connect plug the IR
blaster and receiver. The HDTVA uses some clever electrickery
to send your HD signal across your mains wiring so you can
watch wherever you like. This kit is quite literally a five minute
installation that anyone can do.
Other HDMI over mains products have been on the market
before but what we at Keene like about this one is that it also
makes use of the earth wire to improve transmission distance
and maintain picture quality.
• Plug & Play, Uses your existing power network and
eliminates the need to lay cables.
• Unique SmartLink technology ensures coverage throughout
your home.
• Operate your connected A/V equipment remotely, using the
infrared return feature.
• Through an HDMI splitter built into the transmitter, you
can continue to watch your locally connected equipment
as well.
TECHNICAL INFORMATION
Supported resolutions: 1080p@60/50Hz, 1080i, 720p,
576p, 480p
Supported audio: PCM, up to 3Mbps
Technology: Power network SmartLink PLC with 500Mbps
PHY rate
Video compression: H.264
Latency: (delay) < 260ms
Quality of Service: Smart QoS for video streaming
Range max: 300 metres with SmartLink, 200 metres without
SmartLink (SmartLink uses the earth connection)
Kit Contents
1x HDTV transmitter
2x AAA batteries
1x HDTV receiver
1x IR receiver cable
1x remote
1x IR blaster cable with 1 LED
2x HDMI cables
2x plugs + screws
2x power cables
1x user manual
Code HDTVA £ 279.00
117657_Connections_October_2014.indd 16 16/10/2014 11:21