EL-5500 Advanced HDMI/VGA Presentation Switch OPERATION MANUAL
DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. CYP (UK) Ltd assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be contained in this document. CYP (UK) Ltd also makes no commitment to update or to keep current the information contained in this document.
SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. • To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. • Never spill liquid of any kind on or into this product.
CONTENTS 1. Introduction �������������������������������������������6 2. Applications �������������������������������������������6 3. Package Contents ����������������������������������6 4. System Requirements ���������������������������6 5. Features ��������������������������������������������������7 6. Operation Controls and Functions �������8 6.1 Front Panel ��������������������������������������������������� 8 6.2 Rear Panel ����������������������������������������������������� 9 6.
1. INTRODUCTION The EL-5500 is an advanced rack mountable HDMI, VGA, Composite, and Component presentation switcher. This device can scale and switch input sources to it's two HDMI outputs, with their associated audio signals to the native resolutions supported by the connected display. Control is via the IR remote, RS-232, IP, or via manual selection buttons. Both digital and analogue stereo audio is supported via a built-in DAC (Digital to Analogue Converter) and ADC (Analogue to Digital Converter).
5. FEATURES v1.3 HDMI, HDCP 1.1 and DVI 1.
6. OPERATION CONTROLS AND FUNCTIONS 6.1 Front Panel POWER CV COMP PC 1 PC 2 PC 3 HDMI 1 HDMI 2 HDMI 3 720P MENU - + ENTER XGA 1 2 3 4 5 6 1 POWER & LED: Press this button to switch ON or set the device to standby mode. Once the device is connected with power supply the LED will illuminate and the device will switch to ON automatically. 2 IR: This IR window receives only the IR signal from the remote control included in the package.
6.2 Rear Panel 1 2 5 SERVICE RS232 OUTPUT HDMI 1 HDMI 2 COAX PC/HD R L Cr/Pr Cb/Pb AUDIO AUDIO HDMI 1 HDMI 2 HDMI 3 3 PC 1 6 INPUT CONTROL PC 2 PC 3 4 Y R L POWER CV DC 5V 7 1 SERVICE: Reserved for factory use only. 2 RS-232: Connect with PC/NB and use RS-232 command to control the device. 3 OUTPUT: HDMI 1 & 2: Connect to HDMI display or amplifier for video or video and audio display. COAX: Connect to active speaker or amplifier for audio output in digital format.
5 CONTROL: This port is the link for Telnet or Web GUI controls, connect to an active Ethernet link with an RJ45 terminated cable. 6 POWER: Switch this power toggle to turn on and activate the device or to turn off to shut it down. 7 DC 5V: Plug the power adaptor included in the package and connect it to the AC wall outlet for power supply. 6.3 Remote Control 1 POWER: Press this button to switch ON or set the device to standby mode. Once the device is connected with power supply.
6.
6.
S AUDIODELAY 0~3 Audio delay setting OFF(0) / 40ms (1) / 110ms(2) / 150ms(3) R AUDIODELAY Inquire audio delay setting S AUDIOMUTE 0/1 Audio mute setting R AUDIOMUTE Inquire audio mute setting S KEY LOCK 0/1 Key lock setting R KEY LOCK Inquire key lock setting S RESET 1 Pre-reset S POWER 0/1 Firmware checking R POWER Request power status PORT (0~8) Set active port when repower on LAST MEMORY(0) / HDMI(1) / HDMI2(2) / HDMI3(3) / YPBPR(4) / VIDEO (5) / PC(6) / PC2(7) / PC3(8) ST FW vers.
6.
1ST LAYER 2ND LAYER COLOR COLOR CONTRAST BRIGHTNESS HUE SATURATION SHARPNESS NR. AUDIO VOLUME DELAY SOUND FACTORY RESET SETUP KEY LOCK POWER SAVE INFORMATION INPUT OUTPUT REVISION Factory default setting.
7.
8.
