OR-HD88S CMSI-8H8HS 8 x 8 HDMI Matrix Operation Manual
SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. • To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. • Never spill liquid of any kind on or into this product.
CONTENTS 1. Introduction .............................................. 1 2. Applications ............................................. 1 3. Package Contents .................................. 1 4. System Requirements .............................. 1 5. Features .................................................... 1 6. Operation Controls and Functions ......... 2 6.1 Front Panel ..........................................2 6.2 Rear Panel...........................................3 6.2 Rear Panel.............
1. INTRODUCTION The 8 x 8 HDMI Matrix is a fabulous device for organizing and distributing your HDMI signals. With 8 HDMI input ports and 8 HDMI output ports this device allows a great amount of sources and display to be used motivationally. Moreover, with plenty of control systems such as IR, RS-232 and remote control allow user for all kinds of control habit and occasion to be used. Further, the EDID control settings unlocked the information display freely present. 2.
. OPERATION CONTROLS AND FUNCTIONS 6.1 Front Panel 1 1 2 2 3 3 4 4 5 5 6 6 1 LCM This monitor displays your setting information with each input and output selection. 2 Power button LED Press this button to turn on the device and the green LED will illuminate when the power is on. When the LED illuminate in red it is in standby mode 3 LOCK Press this button to lock all the buttons on the panel. To unlock, just press it again.
and then press Out →E→F→G→H→In→2→Menu. If the menu button is not press the selection will not be changed. 6.2 Rear Panel 1 2 3 4 5 6 7 1 LAN: This slot is to connect with CAT5/6 cable from an IP router for online firmware updating with a website designed by the device’s designer. Or may be a control terminal on-link from a designate IP address. 2 RS-232: This slot is to connect with D-Sub 9pin cable from the PC/NB device for RS-232 control.
6.3 Side Panel 1 Ventilator: These are fan ventilator area, DO NOT block these area or cover it with any object. 7. REMOTE CONTROL 1 1A 2 2 B 3 C 4 D 5 E 6 F 7 G 8 H IN OUT 3 CR-110 1. Power: Press this button to switch on the device or set it to standby mode. 2. IN: Input ports selection 1~8. 3. OUT: Output ports selection A~H.
7.
7.2 RS-232 Commands Command (Case Sensitive) Description A1~A8 Switch output A to 1~8 B1~B8 Switch output B to 1~8 C1~C8 Switch output C to 1~8 D1~D8 SWITCH OUTPUT D TO 1~8 E1~E8 SWITCH OUTPUT E TO 1~8 F1~F8 SWITCH OUTPUT F TO 1~8 G1~G8 SWITCH OUTPUT G TO 1~8 H1~H8 SWITCH OUTPUT H TO 1~8 ABCD...1~ABCD...8 SWITCH OUTPUT ABCD...
8.
9. SPECIFICATIONS TMDS Clock Frequency 2.25 Gbps Input Ports 8 x HDMI, 1 x IR, 1 x RS-232, 1 x USB B type(for firmware update only), 1 x RJ45 (LAN) Output Ports 8 x HDMI ESD Protection Human body model: ± 8kV (Air-gap discharge) ± 4kV (Contact discharge) Power Supply 24V/6.
10.
10 10
11
CYPRESS TECHNOLOGY CO., LTD Home page: http://www.cypress.com.
