CMIR-882 8×8 Bi-directional Infrared Matrix Operation Manual
DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document. Cypress also makes no commitment to update or to keep current the information contained in this document.
SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. • To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. • Never spill liquid of any kind on or into this product.
CONTENTS 1. Introduction �������������������������������������������� 1 2. Applications ������������������������������������������� 1 3. Package Contents �������������������������������� 1 4. System Requirements ���������������������������� 1 5. Features ������������������������������������������������� 2 6. Operation Controls and Functions ������� 3 6.1 Front Panel ����������������������������������������3 6.2 Rear Panel �����������������������������������������4 6.
1. INTRODUCTION The Bi-directional Infrared Matrix is designed to work alongside the 8×8 HDMI matrix, providing control of up to 8 source devices from up to 8 display locations. Using the original or programmable remote controls, source devices such as DVD/Blu-ray players or satellite/set-top boxes can be controlled from any location. 2. APPLICATIONS • Control multiple sources and displays via bi-directional Infrared signals • Extending the range of existing systems • Long distance Infrared control 3.
5. FEATURES • Supports independent IR input and output selection and control • Supports an IR frequency range of 30 kHz~50 kHz • Use your existing remote controls or programmable/universal remote controls • Supports bi-directional IR from input and output locations • Supports RS-232 control, IR remote control and on-panel control • 1U size design Note: This device does not support the sending of audio/video signals, it only transmits and receives infra-red signals.
6. OPERATION CONTROLS AND FUNCTIONS 6.1 Front Panel 8x8 IR Matrix 1 2 3 4 5 6 7 8 IR 1 2 Power All Lock Enter 3 4 5 6 7 1 LCM: Displays the setting information of each input and output setting. 2 IR: IR Receiver window (accepts the remote control signal of this device only). 3 Power: Press this button to power the device on/off. The LED will illuminate green when the power is on, red when it is in 'Standby' mode.
6.2 Rear Panel A RS232 AUX B C D TV E F G H All Out 1 2 3 4 SOURCE 5 6 7 8 All DC 5V RS232 MAIN In 1 2 3 4 5 1 RS-232 AUX: Connect to a device that can be controlled (via D-Sub 9-pin male cable) by RS-232 commands e.g. the 8x8 HDMI Matrix. 2 RS-232 MAIN: Connect to a PC or control system with D-Sub 9-pin male cable for the transmission of RS-232 commands.
Source Out All: Connect to a single IR blaster cable for IR signal transmission, IR signals will be relayed from all TV outputs (A~H) at the same time. Place the IR blaster in direct line-of-sight of the equipment to be controlled. 5 DC 5V: Plug the 5V DC power supply into the unit and connect the adaptor to an AC outlet. 6.3 Remote Control The remote control's settings can be controlled with the four DIP switches on the back of the unit (under the battery compartment cover).
6.4 IR Data Codes NO. DATA NO. DATA 1 88 A 8A 2 8C B 8E 3 90 C 92 4 85 D C6 5 C2 E 99 6 9C F 98 7 D8 G 84 8 87 H 97 6.
6.6 IR Cable Pin Assignment IR Blaster 1 Power 5 V 2 IR Blaster Signal 3 NC IR Extender 1 IR Signal 2 Power 5 V 3 Grounding Note: Both the IR Extender and Blaster support a frequency of 30~50 kHz. 6.
6.8 RS-232 Commands A Command Description A1~A8 Switch output A to 1~8 B1~B8 Switch output B to 1~8 C1~C8 Switch output C to 1~8 D1~D8 Switch output D to 1~8 E1~E8 Switch output E to 1~8 F1~F8 Switch output F to 1~8 G1~G8 Switch output G to 1~8 H1~H8 Switch output H to 1~8 ABCD...1~ABCD...8 Switch output ABCD...
7.
ZONE E NE D ZONE F ZONE G ZONE H IR In (All) RX Link IR 2 Blaster RS232 Out IR 2 Extender RS232 In CAT5e/6 In Power TX Link CAT5e/6 Out PowerDC RX Link IR 2 IR 1 Extender Blaster RS232 Out 24V CAT5e/6 In TX Link IR 2 IR 1 Blaster Extender RS232 In CAT5e/6 Out Power PowerDC RX Link IR 2 IR 1 Extender Blaster RS232 Out 24V CAT5e/6 In TX Link IR 2 IR 1 Blaster Extender RS232 In CAT5e/6 Out Power Link IR 2 IR 1 Extender Blaster PowerDC RS232 Out 24V CAT5e/6 In Link IR
8. SPECIFICATIONS IR Frequency 30 kHz to 50 kHz Source Ports 8×Independent IR Blasters 8×Independent IR Extenders 1×All IR Blaster Control 1×All IR Extender Control TV Ports 8×Independent IR Extenders 8×Independent IR Blasters 1×All IR Blaster Control 1×All IR Extender Control Power Supply 5 V/2.
9.
CYPRESS TECHNOLOGY CO., LTD Home page: http://www.cypress.com.
