CYC MOTOR (BAC) Monitor & customize your e-bike riding experience for all MOTORCYCLE mid-drive systems. Use it as a secondary dashboard, a settings set-up, or both. Customize your ride to suit your style! The CYC Motor (BAC) mobile application is your ideal solution to set up & customize your e-bike experience.
DASHBOARD Bluetooth icon to connect to your device Instantly change mode Real-time speedometer Change between your Dashboard & Settings page © — EEE (HOO ot Rh information icon to provide you 0 with important app usage tips Re ET SHARE Ed TE 0 Warning icon to check error codes & clear faults LHS SR 9 ET km/h Rotor Input Power 0 ere lS EEE ON ICE Es Ea A Motor Temp N All parameters show real-time information 0 EE ii] 0.
CONNECTING A DEVICE Q Choose a Device CR LCR MC Mali ast Q STE ¢? CONNECTED oe TAP TO ey 2 N31 Open the app & select the Bluetooth icon in the top left corner of your dashboard. This icon will be Grey when not connected to a device & red when connected. Make sure that your phone's Bluetooth is enabled. IMPORTANT: Location permission for the app must be enabled. SY) Select the SEARCH button in the bottom left corner to search for your controller. Available e-bikes will then be listed.
QUICK FUNCTIONS oN) FAN CB) Ee (ROO Saki Alec) SEAR EEE RATS e Aik Motor Input Power 0) LGR RE 0.13 » SEE A Motor Temp 0) 0 Throttle In 0.96 v Average Pedal RPM 4 Average Pedal Torque 0 Average Hunan Power 0 bi @ Dashboard — lf Settings SWITCHING MODES For the Motorcycle Ltd's supplied APT displays, you are able to access 2 modes: Race Mode & Street Mode where Race Mode is intended for full power output & Street Mode intended to accommodate your legal regional output requirements for e-bikes.
MAIN SETTINGS PAGE LO e135 Perl OI RIN PERIPHERALS SETUP @) Dashboard SBS PEDAL ASSIST GEYSER fis Settings Information icon A CR CRI FR el "he settings page allows you to navigate though different parameter categories. There are 6 different categories. Each category provides a set of parameters of which some are adjustable & some are readings from your e-bike system. Each category contains an “Information” tab in the top, right hand corner explaining parameters & providing guidelines.
GENERAL () GENERAL General Settings Display Unit Set your units to display in Metric (km) or Imperial (miles). EH EE Metric (km) Oo GENERAL SETTINGS Temperature Unit RH Temperature O51 Set your units to display in degrees Celsius (°C) or Fahrenheit (°F) Software Revision Level EEL Software Revision Level This is the settings version currently installed.
MODES & LEVELS © RACE & STREET MODE MODES & LEVELS Race Mode Throttle You can set the throttle & PAS power output independently for both modes. Sr 3000 Watts RACE MODE THROTTLE & PAS FE Tel TR 100 Hy Race Mode is your “boost” or “full power” mode and has parameters set for reaching closer to the Race Mode PAS system's full capabilities. You can adjust these to your own preference within the capabilities of your chosen controller. The default setting in Race Mode is 3000W & 100km/hr.
MODES & LEVELS 0 MODES & LEVELS Street Mode Throttle Rated Motor Power W Vehicle Maximum Speed Street Mode PAS Rated Motor Power Vehicle Maximum Speed Assist Level Configuration Assist Gain Assist Gain 2 Soto hers hc Speed Limit Assist Assist Speed 1 Assist Speed 2 Assist Speed 8 Others ble Eg Te Throttle Bypass Assist Level Gator RPM Speed Limiting ASSIST LEVEL CONFIGURATION & SPEED LIMIT ASSIST These 2 categories set the factor with which motor power is timed to give an output.
MODES & LEVELS MODES & LEVELS O Street Mode Throttle OTHERS (cont.) Speed Regulator Mode SEL Torque with Speed Limiting In this mode, the throttle controls motor current supplied to the NT motor, but speed limits set in Modes & Levels are considered as well. For example, if you apply 50% throttle, the controller will supply 50% of the rated motor current until it senses that 50% of Street Mode PAS vehicle speed is reached.
THROTTLE () THROTTLE O Throttle Voltage Reading RE ola Rt Eh 5 Throttle Off Voltage Hk) BE iy ETE i) REC RR lE 1s Throttle Ramp Times Positive Motoring Morgue Ramp ms Negative Motoring Morgue Ramp jai THROTTLE SETTINGS Throttle Voltage Reading This non-adjustable value is the voltage reading from your throttle. This value will be just below 1 out of the box, provided that you are using a throttle supplied by CYC Motor. It may be different for throttles supplied elsewhere.
THROTTLE CORE nit: (7) THROTTLE RAMP TIMES The Throttle Ramp Times affect the response times when opening and closing the throttle. Throttle Voltage Reading Positive Motoring Torque Ramp CLT This is the time it takes for the motor to achieve the required input. For example, if you open the throttle fully, it will take 250ms (by default) before the motor gives you full power. It will gradually ramp up to full power within the set time. We recommend not to set this below 150ms.
PEDAL ASSIST OEE, Hardware Input Information ‘hes 2 parameters tell you if your torque sensor is working, and how you would like your overall assist to work. O HARDWARE INPUT INFORMATION Torque Sensor Voltage R11 Control Command Source Throttle or pedal sensor p LL] IVT Sensor NLT The Torque Sensor Voltage can be used to confirm that the torque sensor is connected and that it works properly.
PEDAL ASSIST PEDAL ASSIST © PEDAL SENSOR CONFIGURATION Hardware Input Information his is the pedal (or cadence) sensor settings. Rr 0.057 Pedal Sensor LY There are 4 types of pedal sensors giving you the option to use only the pedal sensor, only the torque sensor, or both: Pedal Sensor Configuration Single Hall Reverse (Only for Gen 1 X1 PRO motors.
PEDAL ASSIST PEDAL ASSIST Hardware Input Information Torque Sensor Voltage 0.
PEDAL ASSIST PEDAL ASSIST 0 TORQUE SENSOR CONFIGURATION (cont.) Pedaled Power Gain You can adjust the sensitivity of the torque sensor by changing this value. If you want the torque Lh 0.057 sensor to be more powerful, increase this value. Hardware Input Information Control Command Source Throttle or pedal sensor hp Decrease it if you want it less powerful. Pedal Power Gain is the factor of input to output.
PEDAL ASSIST QRS, Hardware Input Information Pedal Sensor Configuration Pedal Sensor Type Pedal Speed Sensor Pulses Per Revolution Signal hall torque (LOS) iL: 0 Dg PPR Pedal Sense Delay i Lab Pedaled Maximum Timeout iit ai Pedaled Minimum Timeout SH [41 Pedal Speed Map End Le Pedal Speed Map End 0.
PERIPHERALS SETUP © BRAKE CONFIGURATION PERIPHERALS SETUP Brake 1 Voltage Brake Configuration o This is the voltage read from the brake sensor. Brake 1 Voltage RTP Analogue Brake Off Voltage This is the voltage read from the brake sensor when the magnet is close to or touching the sensor. Analogue Brake Full Voltage Display Analogue Brake Full Voltage This is the voltage read from the brake sensor when the magnet is taken away from the sensor. This is when the brakes are fully engaged.
PERIPHERALS SETUP 0 DISPLAY (cont.) PERIPHERALS SETUP Wheel Speed Sensor Pulses Per Revolution This is the number of magnets in the wheel that is communicating with the speed sensor. For more Sal accurate vehicle speed limiting and measurement, we advise to add more magnets to the wheel.
BATTERY BATTERY General Configuration Rated System Voltage 52 Slow Over Voltage Threshold Slow Under Voltage Threshold 119.985 Fi Fast Over Voltage Threshold 124.951 Fast Under Voltage Threshold DC voltage Trip Clear Hysteresis 59.985 498 GENERAL CONFIGURATION Rated System Voltage This is equal to the nominal voltage of the battery pack you are using. This is where the voltage for the controller is set.
ERROR CODES ERRORS SHOWN ON DISPLAY Error 22H (Throttle voltage out of range) This can be caused by 3 main reasons: 1. The throttle cable has been accidentally unplugged Ensure that the throttle is connected properly 2. The default throttle oft & throttle full voltages have been changed. Confirm that throttle off voltage & throttle full voltage thresholds have been set correctly.
FAULTS & WARNINGS Q Warning Faults: Controller over voltage (flash code 1,1} OTHER FAULTS Bricked Controller To know if your controller is bricked, switch on your bike, connect via the app, & check if values are displayed. If all values show O when connected, it means that your controller is bricked or partially bricked. Ensure that you have waited for the values to load as it may take up to 5 seconds. This is fixable but you will need to contact CYC Support.
BEFORE YOUR RIDE After unboxing & installing your X1 Pro or X1 Stealth, there are a few things you need to set up. NYE Ensure that all wires are properly connected & that your system can switch on by long pressing the display’s power button. Check that the display shows your battery voltage & level. Should your display briefly show Error 30H upon start-up, this is normal as the system takes a moment to connect. Should your battery voltage & level not display refer to step 3.
DISCLAIMER If you require any more information or have any questions about the user manual disclaimer, please feel free to contact us via email at technical or call +852 3690 8938. All the information contained in this user manual is published in good faith and for general informational purposes only. MOTORCYCLE LTD Lid does not make any warranties about the completeness of this information and encourages further inquiries as stated above if needed.
