TOPOLOGY DS103 Display Guide support@cycmotor.
01 Product Details Product Details Product Name Intellegent LCD display, model : DS103 Firmware: CYCMotor Ltd specific firmware Features • Simple and lightweight, separate installation bracket design • High brightness, high contrast 3.5 coloured TFT screen • Clock function (clock is on when the display shutdown) • Excellent outdoor design with IP65 level waterproof • Micro USB serial communication port, convenient maintenance services.
01 Product Details Electrical Specifications • • • • • • • • Power supply：DC 24V/36V/48V/ 52V Rated current：30ma/36V Shutdown leakage current：<1uA Screen specification：3.5” colored TFT（480*320pixels） Communication method：UART (default) Operating temperature：-20°C ~ 60°C Storage temperature：-30°C ~ 80°C Waterproof level：IP65 The information contained in this document is derived from the TFT LCD Display Guide provided by Zhejiang Topology Intelligent Technology Co., Ltd. (otherwise known as Topology).
02 Quick Start Guide Quick Start Guide After unboxing and installing your CYC motor system, there are two main things you need to set up. 1. Change your Battery No. settings according to your rated voltage. Within 15 seconds of turning on your display, long press the MENU button to enter the settings functions. Press UP/DOWN to navigate the settings page & MENU to select. 6s = 22.2 V 7s = 25.9V 8s = 29.6V 9s = 33.3 V 10s = 36V 11s = 40.7V 12s = 44.
03 Functionalities Functionalities Power On/ Off Press and hold the POWER button for 3 seconds to turn the display on/ off. Navigation The MENU button is used to go into your main settings page & your clear data page. It is also used to enter and select a setting or function. 1. 2. 3. 4. POWER MENU UP DOWN Switch Dashboard Switch the main dashboard to display different information by pressing the MENU button.
03 Functionalities Assist Level Operating Press the UP/ DOWN button to change the assist level between level 1, 2, and 3. Note that “OFF” means no motor assistance will be given. Dark & Light Themed Dashboard Long press the UP button to switch between light and dark themed dashboard. The information contained in this document is derived from the TFT LCD Display Guide provided by Zhejiang Topology Intelligent Technology Co., Ltd. (otherwise known as Topology).
03 Functionalities Walk Assist Hold in the DOWN button to activate walk assist. Note that it takes 3 seconds to activate & will deactivate immediately when the button is released. Settings Long press the MENU button within 15 seconds of switching on the display to enter the “Settings” page. Note that once the system has been activated for longer than 15 seconds, you will need to restart the motor system to enter the settings menu.
03 Functionalities Clean Trip Data Wait 15 seconds after starting up the motor system to enter the “Clean Data” menu. Long press the MENU button to clear the previous trip data. Please note that the trip data does not automatically clear once you restart the motor system. This is a manual process. Error Codes In certain circumstances, an error code may appear on your display. Contact technical_support@cycmotor.
04 Installation Installation 1. Determine if you need to select the corresponding mounting clamp and rubber clip ring according to the diameter of your handlebar (Applicable handlebar specifications：Φ22.2 ; Φ25.4 ; Φ31.8). 2. Open the display lock clamp and insert the rubber clip (if applicable) into the correct position of the lock clamp. 3. Set the rubber ring in the bracket (if applicable) then assemble on the middle of the handlebar.
04 Installation Pin Layout Male 5-Pin Connector 1. Red wire: Anode (36V to 72V) 2. Black wire: GND 3. Yellow wire: TxD (display -> controller) 4. Green wire: RxD (controller -> display) 5. Blue wire: Power ord to the controller Cerification CE / IP65 (waterproof ) / ROHS. Be sure to contact techinical_support@cycmotor.com if further assitance is needed.
