CYC Ride Control App Users Guide CYC Motor Ltd Hong Kong
INTRODUCTION CYC RIDE CONTROL Monitor & customize your e-bike riding experience for all CYCMOTOR mid-drive systems. Use it as a secondary dashboard, settings set-up, or both. Unleash all the possibilities of ebike customization at your fingertips. The mobile app is not the only way to customize your system. The controller is also programmable via the included display- integrated for your convenience. This platform is your go-to-station for your CYCMOTOR kit & X6/X12 controllers.
DASHBOARD Brake sensor indicator COMING SOON ALL PARAMETERS SHOW REAL-TIME INFORMATION Warning icon to check error codes & clear faults Bluetooth icon to connect to your device Instantly change between STREET & RACE mode Change between your DASHBOARD & SETTINGS page Serial number connected to the controller ALL PARAMETERS SHOW REAL-TIME INFORMATION © 2022 CYCMOTOR LTD
CONNECTING A DEVICE STEP #1: Open the app and tap the Search button at the bottom of the screen. Kindly ensure your phone’s Bluetooth is enabled. (Please keep close to the motor while connecting) STEP #2: Available devices will then be listed, select your kit and it will begin connecting to the controller. (Please note signal strength) STEP #3: Once connected, the CONNECT icon will change stating you are connected & can select again to disconnect.
MAIN SETTINGS PAGE The settings page allows you to navigate through different parameter categories. There are six different categories with each providing a set of adjustable parameters or readings from your ebike system. IMPORTANT Save all new changes in parameters to flash or risk losing progress. Any changes made that were not saved will be lost after a restart. Note to save after every change in value.
GENERAL TEMPERATURE UNIT Set your units to display in degrees Celsius (°C) or Fahrenheit (°F) SPEED UNIT Set the speed unit to miles or kilometers. MOTOR DIRECTION This setting is for users who’d want to switch the direction to where the motor is facing. Note that this is reserved for specific uses only. WARNING: Do not change this setting if using the motor in its default position. Contact CYC for assistance. RESTORE DEFAULT SETTINGS Restore to factory/default settings.
MODES & LEVELS RACE & STREET MODE You can set the throttle & PAS output independently for both modes. RACE MODE THROTTLE & PAS Race Mode is your “boost” or “full power” mode and has parameters set for reaching closer to the system’s full capabilities. You can adjust these to your own preference within the capabilities of your controller. The default setting in Race Mode is 3000W & 100 km/hr. STREET MODE THROTTLE & PAS Street Mode is intended to be set to your region’s legal limits.
THROTTLE RAMPING TIME This is the time it takes for the motor to achieve the required input. For example, if you open the throttle fully, it will take 250ms (by default) before the motor gives you full power. It will gradually ramp up to full power within the set time. We recommend not to set this below 150ms. INPUT DEADBAND This value pertains to opening the throttle when it’s completely closed.
PEDAL ASSIST PEDAL ASSIST SENSOR Enabling pedal assist. TORQUE SENSOR SENSITIVITY This value pertains to activating pedal assist when it’s completely off. This is the amount of pedal force required to activate the pedal assist. If this value is set higher, your pedal assist will engage with less force and vice versa. POWER RAMP TIME The amount of time it takes to reach the desired input. This is the responsiveness of the motor.
PERIPHERALS SETUP SPEED SENSOR Wheel Diameter The wheel diameter can be measured or calculated. We advise that this number must be calibrated so that vehicle speed within the app matches display speed. This will give more accurate speed liming under different modes. Remember to set the correct wheel size within the display as well (only applicable to 500c & 750c displays). Kindly refer to your user manual. Wheel Magnet This is the number of magnets in the wheel that is communicating with the speed sensor.
BATTERY SERIES OF CELLS 10s = 36V, 14s = 52V, 20s = 72V MAXIMUM VOLTAGE The value the controller will fault when connecting too high a voltage to the system. An error will be triggered if a battery is too high of a voltage. MINIMUM VOLTAGE The value the controller will fault when connecting too low a voltage to the system. This setting can be used to protect your battery if too much voltage sag is detected.
DISCLAIMER If you require any more information or have any questions about the user manual disclaimer, please contact us via email at technical_support@cycmotor.com. All information contained in this user’s guide is published in good faith and for general informational purposes only. CYCMOTOR LTD does not make any warranties about the completeness of this information and encourages further inquiries as stated above if needed.
