PARALYSER 755, 775, 775b &785 USER INSTRUCTIONS CYCL PS VEHICLE SOLUTIONS Proudly designed and engineered in Australia by Dynamco Pty Ltd. P755 P775 P775B 785 User - 2008.
CYCL PS VEHICLE SOLUTIONS THIS CARD SHOULD NOT BE LEFT IN YOUR VEHICLE. IT MUST BE KEPT IN A SAFE SECURE PLACE. -2P755 P775 P775B 785 User - 2008.
Contents INTRODUCTION OPERATIONS REMOTE CONTROLS ARMING AND DISARMING ARM/DISARM SIREN CONFIRMATION SILENT ARMING AUTOMATIC ARMING DOME LIGHT FUNCTION PANIC FEATURE (Car Location) OPEN DOOR WARNING IMMOBILISATION ALARM PROTECTION ZONES DIAGNOSTICS DIAGNOSTIC TABLE 4 5 5 5 6 6 6 7 7 7 8 8 8 9 EMERGENCY OVER-RIDE PIN OVER-RIDE PROCEDURE PROGRAMMABLE OPTIONS OPTION CHANGE PROCEDURE PROGRAMMABLE OPTIONS TABLE PROGRAMMABLE OPTION DESCRIPTIONS CHANGING PIN CODE BATTERY REPLACEMENT SPECIFIC
CYCLOPS P755, P775, P775B & P785 ALARM / IMMOBILISER USER GUIDE CYCL PS VEHICLE SOLUTIONS INTRODUCTION Congratulations on having one of the world’s most advanced alarm/ engine immobilisers installed in your vehicle. This manual describes the features and functions of all four systems. Where as day to day use of the system only involves pressing the remote control, many features of the systems will provide additional convenience for the user.
OPERATIONS REMOTE CONTROLS ALL All systems are supplied with two rolling code remote controls. Each time a button is pressed, the code advances to a completely new code. Each code is only ever used once. ARMING AND DISARMING ALL To arm the system press the main button on the remote control. The vehicle indicators will flash twice. The blue status LED on the dash will flash when the alarm/immobiliser is armed. To disarm the system, press the main button. The indicators will flash once.
ARM/DISARM SIREN CONFIRMATION 75 75B 85 Each time the alarm is armed the siren will chirp twice to confirm the arm operation. The siren will chirp if the automatic arming function arms the system. The siren will also chirp once when the system is disarmed by remote control. SILENT ARMING 75 75B 85 The arm/disarm confirmation chirps can be suspended for one operation by momentarily pressing the secondary button on the remote control before pressing the main button.
DOME LIGHT FUNCTION ALL When the system is disarmed by remote control, the internal circuitry can switch on the car’s dome light for 30 seconds. This feature will be cancelled if the driver turns the ignition switch to the ON position. Factory setting is disabled to avoid unit damage (see “Programmable Options” section for details). PANIC FEATURE (Car Location) 75 75B 85 The alarm can be commanded to “panic” for 30 seconds if the main button is pressed for more than 2 seconds.
IMMOBILISATION ALL The system includes two independent circuits of immobilisation. Each circuit starves the engine of one of it’s critical power supplies. The circuits are designed to be fail-secure, so if a would-be thief was to cut power to the immobiliser, the circuit design will ensure the car remains immobilised. ALARM PROTECTION ZONES 75 75B 85 The alarm protects the vehicle by monitoring all door, bonnet and boot switches, as well as “listening” for the sound of breaking glass.
DIAGNOSTIC TABLE ALL ZONE 1 2 3 4 EMERGENCY OVER-RIDE DESCRIPTION Bonnet Switch Auxiliary Trigger Doors / Boot Switch Glass Breakage ALL If either of the remote controls supplied with the system are lost, broken or stolen, the immobiliser can be disarmed by use of a security key and the unique 4 digit Personal Identification Number (PIN). To disable the security system, turn the key in the rear of the siren 90 degrees. Then follow the PIN procedure in the next section.
PIN OVER-RIDE PROCEDURE ALL To illustrate the PIN over-ride procedure we will assume a PIN of 4,3,2,1. If indicators are still flashing, turn the ignition on and allow the system to reset with all doors closed. • Turn ignition switch to ON position, the status LED will remain lit. • Turn ignition switch to the ACC position and count the LED flashes. • Turn ignition switch ON when the 4th flash has extinguished. • Turn back to ACC position and count 3 flashes, switch ignition ON.
PROGRAMMABLE OPTIONS ALL The systems include 9 programmable options which alter the system functions to comply with the user’s preferences and vehicle special needs. OPTION CHANGE PROCEDURE • • Disarm the system (status LED extinguished). Open the driver’s side door, this must remain open throughout the whole procedure. • Switch the ignition key ON a certain number times (this number corresponds to the option number).
PROGRAMMABLE OPTIONS TABLE IGNITION SWITCH TURNS 1 FLASH DISABLED 3 FLASHES 3 Anti Hijack ENABLED 7 Program New Remote 9 Dome light upon disarm *** Disabled Enabled 11 Horn / Siren Output Style Horn (pulsed) Siren (constant) 13 Arm / Disarm audio confirm Enabled Disabled Press remote 15 120 Second re-lock Enabled Disabled 17 Central Locking Pulse Time *** 0.
PROGRAMMABLE OPTION DESCRIPTIONS ALL Option #3** the Anti Hijack feature locks the car doors when the ignition is switched on, except when a connected door is open. The anti hijack feature unlocks the doors when the ignition is switched off (when driver has reached destination). The feature is disabled if the dome light illumination is extended by the vehicle’s timing circuit. Option #7 programming remote isn’t strictly an optional feature. This feature is used if a spare remote is purchased.
Option #11** determines whether the 30 seconds of siren output is constant or pulsed. The constant output suits a connection to a siren, which allows the siren to sound at full volume. The pulsed output suits the car horn. Option #13** Permanently enables or disables the arm/disarm silent mode. The arm/disarm indicator flashes will occur regardless of whether this option is enabled/disabled. Option #15** enables the auto re-lock feature.
A card with the PIN details must be supplied by your installer. Please contact your installer if the card is missing. Option #21 the alarm system can be set to produce an open door warning when arming. The warning is in the form of a short series of chirps from the siren or horn. This option may not be suitable in cars with dome lights that fade out slowly. CHANGING PIN CODE ALL To alter the PIN code of the system, follow the standard option change procedure; select option #19.
will be confirmed by two indicator flashes. Enter the remaining digits in the same fashion. Four flashes will confirm the programming procedure is complete. Arm the system and confirm the new PIN by completing override procedure. Ensure the new PIN is recorded, but do not leave these details in the vehicle. • BATTERY REPLACEMENT ALL Use a flat head screwdriver to carefully separate the two body pieces taking care not to disturb the circuit board.
SPECIFICATIONS Manufactured by Dynamco Pty Ltd Model Number P755, P775, P775B, P785 Standards Compliance P755 AS/NZS 4601 P775 AS/NZS 4601 and AS/NZS 3749 P775B AS/NZS 4601 P785 AS/NZS 4601 and AS/NZS 3749 Supply Voltage +9VDC - +15VDC Current Consumption less than 20mA (while armed) Country of manufacture China (In Dynamco’s ISO-9002 facility) RF Transmission frequency 433MHz -17P755 P775 P775B 785 User - 2008.
PROBLEM SOLVING • • • System won’t arm. LED on dash won’t flash. • Make sure that ignition switch is in the OFF position. • Ensure the vehicle battery is not flat. • Try your spare remote transmitter unit. System won’t disarm. LED on dash won’t extinguish. • Try spare remote control. • Use Emergency PIN to override system and contact nearest Cyclops service centre.
WARRANTY The Dynamco range of Cyclops Security Systems is covered by an extensive two year warranty (parts & accessories one year). In the unlikely event of a faulty system Dynamco will either replace or repair the system at no cost during the 2 year period. The warranty does allow for the following conditions ~ Subject to the conditions stated below, Dynamco Pty Ltd warranty the product to be free from manufacturing defects and faulty material within the warranty period stated.
WARRANTY REGISTRATION PURCHASED FROM OWNER’S NAME TYPE OF VEHICLE VEHICLE REGO MODEL OF UNIT P.I.N DATE OF MANUFACTURE DATE OF INSTALL’ WARRANTY PERIOD CONTROL MODULE SIREN & REMOTES INSTALLER’S NAME AFTER HOURS EMERGENCY PHONE -20P755 P775 P775B 785 User - 2008.
