Instruction manual
CHANGING PIN CODE
!To alter the PIN code of the system, follow the standard option change
procedure; select option #19.
!The vehicle indicators will flash twice to inform you that the system is
ready to accept the new PIN. The “time-out” is set to two seconds. If
the programming has not begun before then, the system will drop-out
of programming mode.
!Enter the new digits by momentarily pressing the main button on a valid
remote control. The vehicle indicators will flash in response to each
press. Stop pressing when the correct digit count is achieved. The
digit will be confirmed by two indicator flashes.
!Enter the remaining digits in the same fashion. Four flashes will confirm
the programming procedure is complete.
!Arm the system and confirm the new PIN by completing override
procedure. Ensure the new PIN is recorded.
SPECIFICATIONS
Manufactured by : Dynamco Pty Ltd.
Model Number : Paralyser 755.
Standards met : AS/NZS 4601:1999.
Supply voltage : +12VDC
Current consumption : less than 20mA
Country of manufacture : Taiwan
WARRANTY
PROBLEM SOLVING
System won't activate when the door is opened
- Make sure you have used the remote to arm the system. The siren will not
trigger if the system has auto immobilised.
- Make certain the system is activated. LED should be flashing on the
dashboard.
- Make sure that the interior dome light has not been left in the permanently ON
position.
- Make sure that you have allowed at least 10 seconds after setting the system,
before opening the door.
System won't activate or deactivate. LED won't flash or extinguish
- Make sure that ignition switch is in the OFF position.
- Make sure the vehicle battery is not flat.
- Try your spare remote transmitter unit.
The remote fails to operate
If the remote fails to operate and the LED does not light up when the button is
pressed then change the battery. To do this you will need a small “Philips head”
screwdriver. See page 7 for details on battery replacement
ANNUAL INSPECTION
Dynamco prides itself on the durability and integrity of its car security systems.
We welcome users to contact a Cyclops service centre every twelve months for an
annual inspection. (Please note a charge may be levied for this inspection).
The Dynamco range of Cyclops Security Systems is covered by an extensive two
year warranty (parts & accessories one year). In the unlikely event of a faulty
system Dynamco will either replace or repair the system at no cost during the 2
year period. The warranty does allow for the following conditions ~
Subject to the conditions stated below, Dynamco Pty Ltd warranty the product to
be free from manufacturing defects and faulty material within the warranty period
stated.
· That the warranty registration has been completed in full at the time of purchase /
installation and is produced when warranty service is sought
· The warranty does not cover general maintenance such as cleaning / adjusting of
door, boot, bonnet or any entry point switch, nor replacement of consumables
items such as transmitter batteries, lighting circuit bulbs / switches.
The warranty shall be null & void if: -
1. Any person other than by an Authorised Cyclops Sales, Service & Installation
Centre has repaired the product.
2. Should a system / part defect become apparent within the warranty period
DYNAMCO PTY LTD will repair the product free of charge for parts and labour.
The warranty does not cover service labour content or mobile service content.
3. The product has been altered or tampered with in any way, or the serial number
altered, defaced or removed.
4. The defect has been caused by negligence by the owner or their agent / third
party.
5. The product has not been operated correctly, installed by an unauthorised
Cyclops installer or has been subjected to misuse or undue wear and tear
6. Siren, control module, remote controls or any other system part are damaged by
water.
The warranty does not cover the following costs: -
7. Transport of the product to and from Cyclops Service Centres.
WARRANTY REGISTRATION
PURCHASED FROM :
OWNER’S NAME :
TYPE OF VEHICLE :
VEHICLE REGO :
MODEL OF UNIT :
DATE OF INSTALLATION : P.I.N
DATE OF MANUFACTURE :
WARRANTY PERIOD
CONTROL MODULE:
REMOTE CONTROLS :
INSTALLER’S NAME
.
.
.
.
.
.
.
.
.
.
CYCL PS
R
U
I
C
T
Y
E
S
S
S
Y
S
M
T
E
Superior Vehicle Security
1ST INSPECTION
DATE: .
VENUE: .
COMMENT: .
.
SIGNED: .
2ND INSPECTION
DATE: .
VENUE: .
COMMENT: .
.
SIGNED: .
MP
S
A L
E