Instruction manual
5
d) Scrubbing Brushes (76-810x4, 76-830x4, 76-840x4 and 76-870x4)
Genuine Cyclo scrubbing brushes have integral connectors which screw directly into the Cyclo
Polisher replacing the heads. By simply attaching two Cyclo Brushes you can clean carpet,
upholstery, tile, grout and more.
e) ProShine Interface Pad (72-920x2)
Cushion backing plate for ProShine abrasive discs. Interface pads improve performance by allowing
the sanding disc.
Configure the Vibration Elimination System (VES)™ Counterweights on Your Polisher.
a) When new, your polisher will have Cyclo Toolmakers’ exclusive VES counterweight system but may have no
VES weighted insert installed. You will need to install the appropriate weighted insert then install whichever
attachment you will be using: ProGuard OBP, Rubber Pad Holders or Brushes.
b) With power cord not connected, lay the polisher upside-down on your lap, a bench or other flat surface.
c) Determine the attachment system configuration that you intend to use (see section 1 above)
d) Select the appropriate VES weighted insert from the table below.
e) Thread the weighted insert into the counterweight and hand tighten using the 7/32” L-hex key (included).
f) IMPORTANT! Tighten VES weighted insert firmly by attaching the 5/8” flat wrench (included) to the
counterweight’s threaded nut style fitting, and turn counterclockwise until you make contact with the L hex key.
Use the flat wrench pivoting on hex wrench to prevent counterweight from turning while tightening the weighted
insert. Turn the L hex key clockwise to tighten VES weighted insert firmly. Do not overtighten.
Attachment System:
ProGuard™ Orbital
Backing Plates
Carpet And Scrub Brushes
Rubber Pad Holders or
Bonnets over Head Assemblies
Description (part #):
6.5g Weight, Blue (20-072)
18.75g Weight, Silver, 1 Stripe (20-076)
32g Weight, Yellow, 2 Stripes(20-078)
Weighted Insert
(Top And Side Views)
Table 1: Adjustable VES Counterweight Application Table
Why Low Vibration Is Important: Operators face significant risk of muscle, joint and nerve damage caused by the hand-arm vibration of many power tools. By reducing the amount of vibration
you can reduce muscle and joint fatigue as well as the potential risk for permanent damage, as described in the ISO 5349-1:2001 standard, Mechanical vibration -- Measurement and evaluation of
human exposure to hand-transmitted vibration. Cyclo Toolmakers’ machines are designed to minimize vibration.
Attaching ProGuard Orbital Backing Plates, Head Assemblies, Quick Connect Adapters, Scrub Brushes, and other accessories.
a) Lay the polisher upside-down on your lap, a bench or flat surface. You may also
use the cardboard insert removed from inside the polisher box to support polisher
and hold it in place.
b) Fit the flat wrench around the hex nut-like adapter part of the counterweight.
c) Hold the counterweight nut with the flat wrench (see left hand in diagram), and
thread the attachment clockwise. into the counterweight nut (see right hand).
d) Do not over-tighten but use a firm grip for a hand tightening. Repeat the
installation procedure for the other side.
Guide to CTI Pro Paint Care™ Chemicals
& CTI Metal Polishes
Detailing Polishes and Products Selection – CTI Pro Paint Care™ Line and Other Leading Professional Products
Cyclo products are specifically formulated for the speed, action, and weight of the Cyclo Polisher. While many other professional grade machine-application
polishes are also proven to give satisfactory results, the manufacturer’s recommendation for superior results are the field-proven Genuine Cyclo CTI
products and Genuine Cyclo Accessories. For additional information on use and application of other leading professional quality polishes and products,
please visit our website’s support section at www.cyclotoolmakers.com.
Selection of the appropriate detailing chemical is essential for proper results. Many polishes can remove light scratches, and there are products specifically
designed to remove swirl-marks and holograms. There are more aggressive products and it is important to understand the difference between a polish, wax
and sealant. When using these products, read all instructions carefully and we recommend that you always use the least aggressive product and pad
combination necessary for your finish condition.
a) CTI Pro Paint Care Heavy Compounding Gel – Removes scratches, heavy oxidation, orange peel, acid rain damage and other defects.
Aggressive cutting and compounding polish for use on any surface.
b) CTI Pro Paint Care Light Compounding Liquid – Eliminates hairline scratches and oxidation. Leaves a smooth surface ready for polishing.
Follow with our CTI 1 Pass Express™, then our Protective Sealant (Pro Paint Care Polish and Protective Sealant) or Finishing Wax.
c) CTI Pro Paint Care Polish and Swirl Remover – Specially formulated to remove swirls, holograms, light scratches and oxidization. It is the
perfect follow-up to Cyclo's CTI Pro Paint Care Light Compounding Liquid. It does not contain sealants and should be followed with our CTI Pro
Paint Care Finishing Wax and/or Protective Sealant.