User guide

57
Default setting
Expansion Port 1 Expansion Port 2
Dist. XPXT/XPST XPXR XPXT/XPST XPXR
126
to
175'
226'
to
250'
176'
to
225'
76'
to
125'
26'
to
75'
3'
to
25'
JP1JP5JP9
JP2JP6JP10
JP3JP7JP11
JP4JP8JP12
J
P
25
JP1JP5JP9
JP2JP6JP10
JP3JP7JP11
JP4JP8JP12
JP25
JP1JP5JP9
JP2JP6JP10
JP3JP7JP11
JP4JP8JP12
JP25
JP1JP5JP9
JP2JP6JP10
JP3JP7JP11
JP4JP8JP12
JP25
JP1JP5JP9
JP2JP6JP10
JP3JP7JP11
JP4JP8JP12
JP25
JP1JP5JP9
JP2JP6JP10
JP3JP7JP11
JP4JP8JP12
J
P
25
JP13JP17JP21
JP26
JP14JP18JP22
JP15JP19JP23
JP16JP20JP24
JP13JP17JP21
JP26
JP14JP18JP22
JP15JP19JP23
JP16JP20JP24
JP13JP17JP21
JP26
JP14JP18JP22
JP15JP19JP23
JP16JP20JP24
JP13JP17JP21
JP26
JP14JP18JP22
JP15JP19JP23
JP16JP20JP24
JP13JP17JP21
JP26
JP14JP18JP22
JP15JP19JP23
JP16JP20JP24
JP13JP17JP21
JP26
JP14JP18JP22
JP15JP19JP23
JP16JP20JP24
JP12
JP10
JP8
1
1
1
1
1
1
JP11
JP9
JP7
JP12
JP10
JP8
1
1
1
1
1
1
JP11
JP9
JP7
JP12
JP10
JP8
1
1
1
1
1
1
JP11
JP9
JP7
JP12
JP10
JP8
1
1
1
1
1
1
JP11
JP9
JP7
JP12
JP10
JP8
1
1
1
1
1
1
JP11
JP9
JP7
JP12
JP10
JP8
1
1
1
1
1
1
JP11
JP9
JP7
JP6
JP4
JP2
1
1
1
1
1
1
JP5
JP3
JP1
JP6
JP4
JP2
1
1
1
1
1
1
JP5
JP3
JP1
JP6
JP4
JP2
1
1
1
1
1
1
JP5
JP3
JP1
JP6
JP4
JP2
1
1
1
1
1
1
JP5
JP3
JP1
JP6
JP4
JP2
1
1
1
1
1
1
JP5
JP3
JP1
JP6
JP4
JP2
1
1
1
1
1
1
JP5
JP3
JP1
JP1 JP3 JP5
JP8 JP10 JP12
JP2 JP4 JP6
JP7 JP9 JP11
111
11 1
111
11 1
PWB: 016-0112 REV. A
EXPANSION RECEIVER 4XP
EXPANSION REMOTE USER TRANSMITTER
87654321
O
N
PWB: 016-0102 REV. A
JP1JP5JP9
JP13JP17JP21
JP26
JP2JP6JP10
JP14JP18JP22
JP3JP7JP11
JP15JP19JP23
JP4JP8JP12
JP25
JP16JP20JP24
Configuring the Transmitter /Receiver Board Jumpers
Every transmitter and receiver pair must be configured for the length of the expansion
cable that connects them together.
Follow the steps below for each transmitter/receiver pair in your system:
1) Orient your first transmitter/receiver pair as shown below. Note that most
components have been removed to simplify the drawings.
2) Choose which port on the transmitter/receiver you will be connecting your
expansion cable to: the upper Port 2, or the lower Port 1. Either port may be used,
but the same port must be chosen on transmitter and receiver.
3) Using the table below, configure the appropriate jumpers on each board according
to the port chosen and the length of the expansion cable that will connect them. Fill
out the Expansion Configuration Sheets in Appendix B for each board as you
configure it.
TRANSMITTER
(XPXT OR XPST)
RECEIVER
(XPXR OR XPSR)
4) After all of the boards have been configured, you may proceed to the next section,
“Transmitter/Receiver Board and Expansion Cable Installation”.