VR1® Lat/Row Owner’s Manual Strength Systems Part Number 13250-999-4 E www.cybexintl.
Table of Contents Safety Safety Guidelines And Practices . . . . . . . . . . . . . . . . Securing Equipment . . . . . . . . . . . . . . . . . . . . . . . . . Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . Label Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 6 7 8 Assembly Machine Specifications . . . . . . . . . . . . . . . . . . . . . . . 9 Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Assembly Procedures . . . . . . . . . . . . .
Cybex Owner’s Manual Safety Safety Guidelines And Practices Cybex International partners with equipment owners to establish the safest and most effective setup of Cybex equipment. Cybex International urges each facility owner to carefully follow all safety precautions. Following theses precautions are the best protection against personal injury or damage to equipment or facility. The most important safety precaution is to maximize stability for every piece of equipment.
Cybex Owner’s Manual • se the selectorized and plate loaded machines as shown on placards. DO NOT modify the U machine. • ever pin the weights in an elevated position. DO NOT use the machine if found in this condition. N Seek assistance from floor staff. Weights pinned up have the potential to fall if the user pulls the pin. Floor staff should lower the weights to prevent potential problems.
Cybex Owner’s Manual • I nspect the equipment for worn or loose components prior to use. Tighten/replace any loose or worn components before to using. Pay close attention to belts, cables, grips or pulleys and their connections. Always look for potential problems in equipment condition. Loose components should be tightened to function properly. Replacing worn components maintains the equipment is in the best condition for regular use.
Cybex Owner’s Manual Securing Equipment Do not use machine until it is properly anchored. The machine has holes in the feet, which allow for ease in anchoring to the floor. All anchoring holes must be used to maximize stability. Equipment must be secured to a solid, level surface to eliminate rocking, tipping, or falling over due to incorrect usage and misuse.
Cybex Owner’s Manual Warnings and Cautions Warning decals indicate a potentially hazardous situation that could result in death or serious injury if the precautions are not observed. Caution decals indicate a potentially hazardous situation, which, if not avoided, could result in minor or moderate injury. Keep away from moving parts to avoid injury. 2.25 ications 4000Y316-4 A R .25 4 PLACES SAFETY ORANGE PMS 152 BLACK TRIANGLE W/ORANGE EXCLAMATION POINT, BLACK LETTERS 21 PT ARIAL BOLD FONT 8.
Cybex Owner’s Manual Label Placement 4000Y316-X 8500-311-X 8500-025-X 4000Y316-X 4605-381-X 4000Y316-X 8
Cybex Owner’s Manual Assembly Machine Specifications Total Weight and Size VR1 Lat/Row 13250 Standard Stack Weight 496 Lbs 225 Kg Machine Dimensions at Rest 73” L x 50” W x 77” H 185 cm L x 127 cm W x 211 cm H Machine Dimensions in Use Same Same Total Weight and Size VR1 Lat/Row 13250 Standard Stack Weight 426 Lbs 194 Kg Machine Dimensions at Rest 73” L x 50” W x 77” H 185 cm L x 127 cm W x 211 cm H Machine Dimensions in Use Same Same Tools Required • 7/32” Allen wrench • 3/4” Socket or wrench • Hamm
LIG HT LIG HT STA CK 130 00- 14 WE IGH 032 1 4800-557 1 99 CK 14 W pla tes ATE pla tes TP 13000-552 STA 470 EIG 0-0 0c0 HT Cybex1300Owner’s Manual 32 70 PL LAT 470 0c0 ED 97 97 70 DET AIL STA ND ETA IL STA ARD STA CK 98 99 ND ARD STA Decal, CK Weight Plate (10-150) (Light) 3 8 98 Decal, 38 Weight Plate (10-220) (Standard) 100 38 38 1 14 4700-337 13000-032 96B 96A 9p late LIG late 14 s 47 00c 073 ? 4700-338 ?A STA 13000-036 CK Move to desired lo
Cybex Owner’s Manual If Then 4. Remove guide rod caps. Guide rod cap contains a compression spring that will fly if grasp is not released slowly. Slide spring loaded guide rod cap down guide rod until cap is clear of frame. Slowly release grasp of guide rod cap and remove. Guide Rod Cap Guide Rod Cap Compression Spring Compression Spring Guide Rods 5. Remove guide rod cap and springs. 6. Repeat procedure for opposite guide rods.
Cybex Owner’s Manual Securely anchor machine to the floor Cybex strongly recommends to maximize stability, equipment must be secured to a solid level surface. CAUTION: Cybex is not responsible for the actual anchoring of equipment. Consult with a professional contractor. WARNING: Use fasteners having a minimum of 500 lbs. tensile capacity (3/8’’ grade 2 bolts or better). WARNING: If legs/frame does not contact surface, DO NOT pull down with anchors.
Cybex Owner’s Manual 3. Place weight stack pin in each plate to verify proper installation. 4. Lift top weight up and down simulating normal operation (without selecting any resistance). 5. Verify that the cable is moving smoothly and is routed straight from the pulley bracket to the top of the weight plate connector. Install back shroud 1. Place shroud into position. 2. Secure top in place using two BHSCS and 7/32” Allen wrench.
Cybex Owner’s Manual Exercise Intended Use The intended commercial use of this machine is to aid exercise and improve general physical fitness. Instructions ead and understand all instructions and warnings prior to using this machine in the Safety R section of the Owner’s Manual. All adjustment points on the machine have yellow handles or knobs. Lat Pull 1. Adjust arm assembly to the vertical position. 2. Adjust thigh pad for stabilization during exercise. 3.
Cybex Owner’s Manual Maintenance All preventive maintenance activities must be performed on a regular basis. Performing routine preventive maintenance actions can aid in providing safe, trouble-free operation of all Cybex Strength Systems equipment. ybex is not responsible for performing regular inspection and maintenance actions for your C machines. Instruct all personnel in equipment inspection and maintenance actions and also in accident reporting/recording.
Cybex Owner’s Manual Clean Upholstery If Then 1. Prepare a solution of 10% household liquid soap and warm water. 2. Apply with a soft damp cloth. Light Soiling 3. If necessary, apply a solution of liquid cleanser with a soft bristle brush. 4. Dampen a clean soft cloth in water and wipe residue away. 1. Prepare a solution of 10% household bleach (sodium hypochlorite) and 90% water. Dampen a soft white cloth in the solution. 2. Rub gently on the stained area. 3.
Cybex Owner’s Manual Clean Chrome Clean chrome tubes, first using chrome polish and then using a car wax seal. Neutral cleaners with a pH between 5.5 and 8.5 are recommended. Be sure to dry thoroughly. AVOID acid or chlorine based cleaners and also cleaners containing abrasives as these could scratch or damage the equipment. Guidelines for cleaning front panel: se clean soft cloths or sponges for application of cleaners and again for washing and rinsing.
Cybex Owner’s Manual Weekly Procedures Inspect All Nuts and Bolts Tighten all loose nuts and bolts as required. WARNING: Serious injury or death may result if the following precautions are not followed. Replace all worn cables and belts. Worn cables and belts can fail if not replaced. Inspect cables and belts Inspect all cables and belts for wear or damage and proper tension.
Cybex Owner’s Manual Belts Condition of Belt 3D View 3D or Side View Peeling of the belt’s skin. Wave in belt Belt is necked down (narrow section) Replace belt if any Examine edge of belt (both sides). section is over 1/32” Replace belt if any section is (.03) narrower than the narrower than the rest. rest of belt Cracks or splits One or more strands of kevlar is hanging out, or if there is a significant amount of frayed kevlar.
Cybex Owner’s Manual CAUTION: Personal injury or property damage may occur if the following precautions are not followed. Do not use if less than 1/8” of material remains to the edge. Replace all worn handles immediately. Failure to replace worn handles can result in injury or property damage. Inspect bars and handles for wear, paying particular attention to tab area connection points. Replace bar if less than 1/8” of material remains to the edge.
Cybex Owner’s Manual Cable Adjustment Tools Required 9/16” Wrench (2) Four types of cable tension adjustment are used on Cybex Strength Systems: Cable Adjustment Description Diagram This type of adjustment uses a jam nut and a tension adjustment nut at Jam Nut the cable cam end as the primary Adjustment adjustment. The other end of the cable usually contains a roll pin adjustment. This type of adjustment uses a socket head cap screw (SHCS) securing a cable rod end bearing to Rod End the machine.
Cybex Owner’s Manual Belt Adjustment Tools Required • • 7/32” Wrench Torque wrench (lbs-in) Belt Adjustment Action 1. Using a 7/32” Allen wrench loose set screws. 2. Pull belt tight. Loose Belt 3. Secure belt in place with set screws. 4. Torque set screws to 300-350 lb-in. 5.
Cybex Owner’s Manual Customer Service Product Registration To register product do the following: 1. Visit www.cybexintl.com. 2. Locate Product Registration in the Support section. 3. Fill out form completely. 4. Click the Submit button to register product. Contacting Service Hours of phone service are Monday through Friday from 8:30 a.m. to 6:00 p.m. Eastern Standard Time. For Cybex customers living in the USA, contact Cybex Customer Service at 888-462-9239.
Cybex Owner’s Manual Ordering Parts TTo order parts online go to www.cybexintl.com. Select Support > Parts / Ordering. In the left navigation panel, click Parts Diagrams - Current Products. Select from the drop down boxes. To speak with a customer service representative, call 888-462-9239 (for customers living within the USA) or 508-533-4300 (for customers outside the USA). The following information located on the serial number decal will assist our Cybex representatives in serving you.
Cybex Owner’s Manual Damaged Parts Materials damaged in shipment should not be returned for credit. Shipping damages are the responsibility of the carrier (UPS, Federal Express, trucking companies, etc.) Apparent Damage Upon receipt of your shipment, check all items carefully. Any damage seen with a visual check must be noted on the freight bill and signed by the carrier’s agent. Failure to do so will result in the carriers refusal to honor your damage claim.
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183 www.cybexintl.
