Cybex 600T Treadmill Owner’s Manual Cardiovascular Systems Part Number LT-03157 Rev C Cybex and the Cybex logo are registered trademarks of Cybex International, Inc. Stableflex and the Stableflex logo are registered trademarks of Cybex International, Inc. Polar is a registered trademark of Polar. DISCLAIMER: Cybex International, Inc. makes no representations or warranties regarding the contents of this manual.
IMPORTANT WARRANTY INFORMATION To validate this warranty, complete the following information and return this card to Cybex within ten days of equipment installation.
NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES BUSINESS REPLY MAIL FIRST CLASS MAIL PERMIT NO.
Cybex 600T Treadmill Owner’s Manual About This Manual For your convenience, all measurements and voltage requirements are listed in both English and metric units. English values are listed first, followed by metric units in parentheses. For example: 1” (2.54 cm). An Owner’s Manual is shipped with each 600T Treadmill. To purchase a copy of the Service Manual contact Cybex Customer Service at 800-766-3211 then press 63 or 508-533-4300.
Cybex 600T Treadmill Owner’s Manual Declaration of Conformity We declare that to the best of our knowledge that the fitness equipment listed below, and manufactured by: Cybex International, Inc.
Cybex 600T Treadmill Owner’s Manual Table of Contents Front Pages About This Manual . . . . . . . . . . . . . . . . . i FCC Compliance Information . . . . . . . . . . i Declaration of Conformity . . . . . . . . . . . . ii Table of Contents . . . . . . . . . . . . . . . . . . iii 4 Preventive Maintenance 1 Safety 5 Setup & Assembly Important Voltage Information Grounding Instructions . . . . . Important Safety Instructions Warning Labels . . . . . . . . . . . Caution Labels . . . . . . . . . . . . . .
Cybex 600T Treadmill Owner’s Manual
Cybex 600T Treadmill Owner’s Manual 1 - Safety IMPORTANT: Read all instructions and warnings before using the treadmill. Important Voltage Information Before you assemble your 600T, check to make sure that the treadmill has the correct voltage requirements for your area, and that you have the correct model. This treadmill is for use on a nominal 115 VAC ±10%, 60 Hz and 20 amps or a 220 VAC ±15%, 50 Hz/60 Hz and 15 amps grounded, dedicated circuit.
Cybex 600T Treadmill Owner’s Manual treadmill are a grounded, dedicated circuit, rated for one of the following: 115 VAC ±10%, 60 Hz and 20 amps or a 220 VAC ±15%, 50 Hz/60 Hz and 15 amps. Make sure that the treadmill is connected to an outlet having the same configuration as the plug. Do not use a ground plug adapter to adapt the power cord to a non-grounded outlet.
Cybex 600T Treadmill Owner’s Manual • Do not operate the treadmill if the cord is damaged, if the treadmill is not working properly, or if the treadmill has been dropped or damaged. Seek service from a qualified technician. • Do not place the cord near heated surfaces or sharp edges. • Do not use the treadmill outdoors. • Do not operate the treadmill around or where aerosol (spray) or where oxygen products are being used. • Read and understand the Owner's Manual completely before using the treadmill.
Cybex 600T Treadmill Owner’s Manual Warning Labels Warning decals indicate a potentially hazardous situation, which, if not avoided, could result in death or serious injury. The warning decal used on the 600T is shown below. SERIOUS INJURY COULD OCCUR IF THESE PRECAUTIONS ARE NOT OBSERVED 1. Obtain a medical exam before beginning any exercise program. 2. Keep children away. Teenagers and disabled must be supervised. 3. Obtain instruction before using. 4.
Cybex 600T Treadmill Owner’s Manual Caution Labels Caution decals indicate a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury. The caution decals used on the 600T are shown below. To replace any worn or damaged labels do one of the following: Visit eCybex.com to shop for parts online, or download the parts order form and fax your order to 508-533-5183. To speak with a customer service representative, in most areas call 800-766-3211 then press 63.
Cybex 600T Treadmill Owner’s Manual Page 1-6
Cybex 600T Treadmill Owner’s Manual 2 - Technical Specifications Specifications Length: 83" (211 cm) Width: 33" (84 cm) Running Area: 20" x 60" (51 cm x 152.4 cm) Weight of Product: 450 lbs. (203 kg) Speed Range: 0.5 to 10.0 mph (0.8 to 16.1 kph) in 0.1 mph or 0.
Cybex 600T Treadmill Owner’s Manual Stableflex System The Cybex 600T treadmill also has a feature you can find only in Cybex treadmills, Stableflex. Stableflex is laterally stable at the back and vertically flexible at the front. As a result of its high internal dampening, Stableflex allows shock to be absorbed where it occurs, and minimizes the impact.
Cybex 600T Treadmill Owner’s Manual 3 - Operation Quick Start Press the Quick Start key. After a 3-second countdown, the running belt will start at 1 mph (1.6 kph) in the Manual program. Use the and arrows to change speed and elevation. NOTE: For an accurate calorie count, you must correctly set your weight (including clothing) by pressing the Weight key. Stopping the Treadmill Press Pause/Stop to temporarily stop your workout.
Cybex 600T Treadmill Owner’s Manual Selecting Programs & Options Every key on the display is usable during operation. Any key may be pressed at any time to make adjustments in speed, elevation, level, program choice, workout time, or data readouts. Displaying Heart Rate In order for the 600T to display your heart rate, you must either use a Polar compatible heart rate transmitter belt, or your treadmill must have the optional Contact Heart Rate.
Cybex 600T Treadmill Owner’s Manual Detailed Operation Guide Dormant Mode — When the treadmill is not in use, the console will display a constantly changing geometric pattern to show that power is on. If the treadmill is equipped with Contact Heart Rate, the console will display a beating heart. Heart rate is displayed if a heart rate signal is detected. Activating the Treadmill — Follow the steps below: 1. Place the emergency stop key in the location as shown in Figure 2.
Cybex 600T Treadmill Owner’s Manual Control During Operation Every key on the display is usable during operation. Any key may be pressed at any time to make adjustments in speed, elevation, level, program choice, workout time, or data readouts. Changing Speed — Use the Speed and keys arrows to change the speed in increments of 0.1 mph or 0.10 kph. Maximum speed is 10 mph (16 kph). Changing Elevation — Use the Incline and arrows to change the elevation in increments of 1%. Maximum elevation is 15%.
Cybex 600T Treadmill Owner’s Manual Changing Data Readouts You may request a specific data type to be displayed by pressing one of the Display Options keys. The treadmill's data readouts may also be set to Scan, where the data type is changed every five seconds. (Scan can be made the default readout mode in Test Mode; see Setting Operations Options in chapter 5.) The readout options are: Distance — The total accumulated distance, in miles or kilometers, during your workout.
Cybex 600T Treadmill Owner’s Manual Use of Programs Using Hills, Endurance, or Sport Programs Any workout time between one and 60 minutes may be entered. These three programs share a common 2.5-minute warm-up and cool-down. If the time is two minutes or less, only part of the warm-up is used. If the time is three to five minutes, the warm-up and part of the cooldown is used. The cool-down is aligned to the end of the program.
Cybex 600T Treadmill Owner’s Manual Using Heart Rate Control Program NOTE: Obtain a medical exam before beginning any exercise program. NOTE: This program requires the user to wear a Polar or compatible heart rate transmitter belt. The Heart Rate Control Program (HRCP) cannot be selected on the control console unless the treadmill detects a heart rate signal. The HRCP will not work with the optional handgrip heart rate system.
Cybex 600T Treadmill Owner’s Manual Page 3-8
Cybex 600T Treadmill Owner’s Manual 4 - Preventive Maintenance Regular Maintenance Activities Cleaning Your Treadmill — When cleaning your treadmill spray a mild* cleaning agent, such as a water and dishsoap solution, on a clean cloth first, and then wipe the treadmill with the damp cloth. Front Pages About This Manual . . . . . . . . . . i FCC Compliance Information . i Declaration of Conformity . . . . ii Table of Contents . . . . . . . . . .
Cybex 600T Treadmill Owner’s Manual Also use a dry cloth for the areas that you can't reach with the vacuum cleaner. If the machine has not been used for some time or is excessively dirty, use a dry cloth to wipe all exposed areas. Replace the cover and screws when finished. Four Times Per Year — Clean the belt and the deck surfaces to minimize the effect of friction between the wood deck and the running belt.
Cybex 600T Treadmill Owner’s Manual belt is slipping. If the belt does slip, use a wrench to equally tighten both rear roller adjustment bolts 1/2 of a turn (clockwise). Adjust the belt until no further slipping is felt. Running Belt Maintenance The running belt and deck should be checked periodically for any excessive wear. The belt may need minor adjustments. Use the following section to help keep your 600T operating properly.
Cybex 600T Treadmill Owner’s Manual C. Remove the other side rail and set aside. 3. Check belt condition. A. Run your hand under the belt on the top of the deck surface. If you notice any excessive ridges, furrowing or cracks in the deck or if the deck feels very rough, the surface may have worn down to a point where it could start to cause excessive wear to the undersurface of the running belt. If belt needs replaced contact the nearest authorized Cybex dealer or other competent repair service.
Cybex 600T Treadmill Owner’s Manual 5 - Setup & Assembly Quick Setup Quick Setup - For Experienced Fitness Professionals Only 1. The power requirements for this treadmill are 115 VAC ±10%, 60 Hz and 20 amps or a 220 VAC ±15%, 50 Hz/60 Hz and 15 amps grounded, dedicated circuit. The location should be level, with good ventilation, and not in an area of high humidity. 2. Assemble the treadmill using the instructions in the "Setup & Assembly" chapter. 3. Connect CSAFE equipment (if applicable). 4.
Cybex 600T Treadmill Owner’s Manual Item Qty Description 1 1 Base, console and uprights 2 12 Screws for uprights, handlebar, and base covers 3 1 Motor cover 4 2 Motor cover screws 5 2 Base covers 6 8 Junction cover screws 7 4 Junction covers Figure 1 Page 5-2
Cybex 600T Treadmill Owner’s Manual Electrical Power Requirements This treadmill is for use on a nominal 115 VAC ±10%, 60 Hz and 20 amps or a 220 VAC ±15%, 50 Hz/60 Hz and 15 amps grounded, dedicated circuit. Contact your electrician if you have any doubts about your electrical service. Do not use a ground plug adapter to adapt the 3-prong power cord plug to a non-grounded electrical outlet. Do not use an extension cord. Unpacking Unpack and remove the treadmill parts from the shipping container.
Cybex 600T Treadmill Owner’s Manual Assembling the Treadmill To ensure correct assembly of the treadmill, carefully follow these steps: NOTE: In this manual the words “left” and “right” are from the treadmill user's point of view. 1. Move the treadmill into position. A. The shipping box has a small ramp at the front end of the treadmill base. After removing the boxes, parts, and plastic wrapping from the top of the base, lift the back end of the treadmill and roll it down the ramp. B.
Cybex 600T Treadmill Owner’s Manual 6. Attach the base covers. A. Locate the two base covers (metal). Place them over the base of each upright. The left will only fit on the left side and the right will only fit on the right side. B. Using a 1/2" wrench, secure the base covers with four screws provided in bag 1. See Figure 3. Hex Head Screws (5 each side) Base Cover Front Pages About This Manual . . . . . . . . . . i FCC Compliance Information . i Declaration of Conformity . . . . ii Table of Contents .
Cybex 600T Treadmill Owner’s Manual 8. Attach the junction covers. A. Place the set of junction covers with the bottle holder over the right handlebar to upright junction and secure them with four Phillips head screws provided in bag 2. See Figure 5. B. Place the remaining set over the left handlebar to upright junction. Secure them with four Phillips head screws provided in bag 2. See Figure 5. Junction Covers Bottle Holder Figure 5 9. Attach emergency stop key. A.
Cybex 600T Treadmill Owner’s Manual Front Pages About This Manual . . . . . . . . . . i FCC Compliance Information . i Declaration of Conformity . . . . ii Table of Contents . . . . . . . . . . iii 1 Safety Important Voltage Information 1-1 Grounding Instructions . . . . 1-1 Important Safety Instructions 1-2 Warning Labels . . . . . . . . . . 1-4 Caution Labels. . . . . . . . . . . 1-5 2 Technical Specifications Specifications . . . . . . . . . . . 2-1 Stableflex System . . . . . . . .
Cybex 600T Treadmill Owner’s Manual F. Fasten the back console with the screws removed during step 11A. NOTE: The two gold screws are for the accessory holder. ! WARNING: Be sure that all electrical requirements are met as indicated in the specifications at the front of the manual and at the beginning of this chapter prior to proceeding. Test the 600T Operation Use the following instructions to test the full speed and incline range of the treadmill and to check the belt for proper operation. 1.
Cybex 600T Treadmill Owner’s Manual 9. As you press the Incline or Speed or will show the actual incline or speed. keys, the respective displays 10. When the treadmill reaches the set incline and speed, the displays will stop flashing and remain steadily illuminated to indicate that the desired settings have been reached. 11. Run the treadmill through its full % grade range. Press the Incline key until the treadmill reaches its highest grade (15%).
Cybex 600T Treadmill Owner’s Manual D. Line Frequency: frequency of the power line that supplies power to your treadmill. The default setting is 50 Hz for metric consoles and 60 Hz for English consoles. NOTE: If you have an English console and a 50 Hz power line frequency, then you must change the default setting from 60 Hz to 50 Hz for the proper elevation frequency. Remember: You must press Enter after changing a value for that value to be stored. 4. To exit Test Mode press the Pause/Stop key twice.
Cybex 600T Treadmill Owner’s Manual 6 - Customer Service Contacting Service In most areas call 800-766-3211 then press 63. Otherwise call 508-533-4300 or fax 508-533-5183. Hours of phone service are Monday through Thursday from 8:30 a.m. to 6:00 p.m. and Friday from 8:30 a.m. to 5:00 p.m. Eastern Standard Time. Information can be found on the web at www.eCybex.com or by email at techhelp@cybexintl.com. Serial Number & Voltage Your serial number can be found on the rear crossbar under the running deck.
Cybex 600T Treadmill Owner’s Manual 4. At Cybex’s discretion, the technician may request that you return the problem part(s) to Cybex for evaluation and repair or replacement. The technician will assign you an RMA number and will send you an ARS label. The ARS label and RMA number must be clearly displayed on the outside of the package that contains the item(s) to be returned.
