Cybex Pro+ Treadmill Service Manual Cardiovascular Systems Part Number LT-21649-4 A www.cybexinternational.
Cybex Pro+ Treadmill Service Manual Cardiovascular Systems Part Number LT-21649-4 A Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc. Safety Sentry™ is a registered trademark of Cybex international, Inc. Polar® is a registered trademark of Polar. DISCLAIMER: Cybex International, Inc. makes no representations or warranties regarding the contents of this manual.
Cybex Pro+ Treadmill Service Manual About This Manual An Owner’s Manual is shipped with each unit. To purchase additional copies of the Owner’s Manual or any other Cybex manual, please do one of the following: • • Fax orders to 508-533-5183 Contact Cybex Customer Service at 888-462-9239 or 508-533-4300 To contact Cybex with comments about this manual send an email to techhelp@cybexintl.com.
This page intentionally left blank.
Table of Contents Front Pages About this Manual . . . . . . . . . . . . . . . . . . i FCC Compliance Information . . . . . . . . . i Table of Contents . . . . . . . . . . . . . . . . . iii 1 Safety Important Voltage Information . . . . . . . Grounding Instructions. . . . . . . . . . . . . Important Safety Instructions . . . . . . . . Warning Decals . . . . . . . . . . . . . . . . . . Caution Decals. . . . . . . . . . . . . . . . . . . Emergency Stop Key (e-stop) . . . . . . .
Cybex Pro+ Treadmill Service Manual This page intentionally left blank.
Cybex Pro+ Treadmill Service Manual 1- Safety IMPORTANT: Read all instructions and warnings before using the treadmill. Important Voltage Information Before plugging the power cord into an electrical outlet, verify that the voltage requirements for your area match the voltage of the treadmill that you have received.
Cybex Pro+ Treadmill Service Manual Important Safety Instructions (Save These Instructions) ! DANGER: To reduce the risk of electric shock, always unplug this treadmill from the electrical outlet immediately after using it and before cleaning it. ! WARNING: Serious injury could occur if these precautions are not observed. To reduce the risk of burns, fires, electric shock, or injury: User Safety Precautions • DO NOT wear loose or dangling clothing while using the treadmill.
Cybex Pro+ Treadmill Service Manual • DO NOT operate electrically powered treadmills in damp or wet locations. • Keep the running belt clean and dry at all times. • DO NOT leave the treadmill unattended when plugged in and running. NOTE: Before leaving the treadmill unattended, always wait until the treadmill comes to a complete stop and is level. Then, turn all controls to the STOP or OFF position and remove the plug from the outlet. Remove the e-stop key from the treadmill.
Cybex Pro+ Treadmill Service Manual • Ensure all User and Facility safety precautions are observed. • Carefully read and understand the following before using the Cybex Pro+ treadmill: • Warning Decals • Caution Decals To replace any worn or damaged decals do one of the following: Fax orders to 508-533-5183 or contact Cybex Customer Service at 888-462-9239. If you live outside of the USA, call 508-533-4300. For location or part number of labels, see the parts list and exploded-view diagram.
Cybex Pro+ Treadmill Service Manual All maintenance activities shall be performed by qualified personnel. Failure to do so could result in serious injury. Service Schedule NOTE: This is the minimum recommended service. 1. Determine mileage. Date Mileage Service Initials A. Enter Test Mode by holding down any key while turning the treadmill to the on (I) position. dist (except on all B. Press Cybex Sport models). DIST appears on the display. First 500 Miles A Check Running Belt Tension & Tracking.
Cybex Pro+ Treadmill Service Manual Safety Page 1-6
Cybex Pro+ Treadmill Service Manual Caution Decals Caution decals indicate a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury. There are no caution decals used on the Cybex Pro+ treadmill. However, there is a caution in the installation instructions for initial installation only. See below.
Cybex Pro+ Treadmill Service Manual Emergency Stop Key (e-stop) The e-stop key functions as the emergency stop. In an emergency situation, remove the e-stop key and the treadmill will come to a stop. Before using the treadmill, clip the e-stop key as described below. 1. Clip the e-stop key to your clothing. NOTE: Be sure the string is free of knots and has enough slack for you to run comfortably with the e-stop key in place. 2.
Cybex Pro+ Treadmill Service Manual 2 - Preventive Maintenance Warnings/Cautions All warnings and cautions listed in this chapter are as follows: ! WARNING: All maintenance activities shall be performed by qualified personnel. Failure to do so could result in serious injury. ! WARNING: To prevent electrical shock, be sure that power is shut off and the treadmill is unplugged from the electrical outlet before performing any cleaning or maintenance procedures.
Cybex Pro+ Treadmill Service Manual Cleaning Your Treadmill When cleaning your treadmill spray a mild cleaning agent, such as a water and dishsoap solution, on a clean cloth first and then wipe the treadmill with the damp cloth. NOTE: Do not spray cleaning solution directly on the treadmill. Direct spraying could cause damage to the electronics and may void the warranty.
Cybex Pro+ Treadmill Service Manual Running Belt Maintenance Belt and Deck – Clean the belt and the deck surfaces to minimize the effect of friction between the wood deck and the running belt. Clean the underside of the running belt and the top of the running deck surface by wiping them with a clean dry towel. This should be done often to prevent premature wear of the deck, running belt, and the drive motor system. See the Service Schedule in this chapter to determine the minimum recommended cleaning.
Cybex Pro+ Treadmill Service Manual 2. Center the belt. NOTE: While centering the belt choose one bolt to adjust. Do not adjust both bolts. A. With the treadmill running at 5 mph (8 kph) observe the running belt. If the belt tracks off center to the right or left the deck will become exposed. Use a 3/4” socket wrench to tighten the rear roller bolt on the side of the treadmill toward which the belt is moving.
Cybex Pro+ Treadmill Service Manual Side Panel Top Steps End Caps Screws Side Panel Figure 3 4. Remove the side panels. A. Pull each side panel out and off the treadmill. See Figure 3. 5. Remove the top steps. A. Using a Phillips screwdriver, remove the three screws that hold each top step in place. See Figure 4. Screws (3 Under Each Top Step) B. Grasp each top step and lift it out and off the treadmill. See Figures 3 and 4. 6. Check the belt and deck condition. A.
Cybex Pro+ Treadmill Service Manual 8. Secure the top steps. A. Place each top step in position. See Figure 4. B. Using a Phillips screwdriver, tighten the three screws that hold each top step in place. See Figure 4. 9. Secure the end caps. A. Using a Phillips screwdriver, tighten the screw securing each end cap in place. See Figure 3. 10. Secure the side panels. A.
Cybex Pro+ Treadmill Service Manual Service Schedule All maintenance activities shall be performed by qualified personnel. Failure to do so could result in serious injury. NOTE: This is the minimum recommended service. 1. Determine mileage. A. While in Dormant Mode enter Test Mode by holding down any key while turning the treadmill to the on (I) position. B. Press the DIST button to display “DIST” and miles or kilometers will be displayed. C. Record Mileage. NOTE: To exit Test Mode, press the Stop key .
Cybex Pro+ Treadmill Service Manual This page intentionally left blank Preventive Maintenance Page 2-8
Cybex Pro+ Treadmill Service Manual 3 - Customer Service Contacting Service Hours of phone service are Monday through Friday from 8:30 a.m. to 6:00 p.m. Eastern Standard Time. For Cybex customers living in the USA, contact Cybex Customer Service at 888-462-9239. For Cybex customers living outside the USA, contact Cybex Customer Service at 508-533-4300 or fax 508-533-5183. Find information on the web at www.cybexinternational.com or by e-mail at techhelp@cybexintl.com.
Cybex Pro+ Treadmill Service Manual Return Material Authorization (RMA) The Return Material Authorization (RMA) system outlines the procedures to follow when returning material for replacement, repair, or credit. The system assures that returned materials are properly handled and analyzed. Follow the following procedures carefully. Contact your authorized Cybex dealer on all warranty-related matters. Your local Cybex dealer will request an RMA from Cybex, if applicable.
Cybex Pro+ Treadmill Service Manual Damaged Parts Materials damaged in shipment should not be returned for credit. Shipping damages are the responsibility of the carrier (UPS, Federal Express, trucking companies, etc.) Apparent Damage – Upon receipt of your shipment, check all boxes carefully. Any damage seen with a visual check must be noted on the freight bill and signed by the carrier's agent. Failure to do so will result in the carrier's refusal to honor your damage claim.
Cybex Pro+ Treadmill Service Manual Ordering Parts Fax orders to 508-533-5183. To speak with a customer service representative, call 888-462-9239 (for customers living within the USA) or 508-533-4300 (for customers outside the USA). CAUTION Use only Cybex replacement parts when servicing. Failure to do so could result in personal injury. Cybex will void warranty if non-Cybex replacement parts are used.
Cybex Pro+ Treadmill Service Manual 4 - Service Warnings/Cautions All warnings and cautions listed in this chapter are as follows: ! WARNING: All maintenance activities shall be performed by qualified personnel. Failure to do so could result in serious injury. ! CAUTION: Use only Cybex replacement parts when servicing. Failure to do so could result in personal injury. ! WARNING: Disconnect the power cord before beginning this procedure. ! WARNING: Do not touch components on the lower board.
Cybex Pro+ Treadmill Service Manual ! WARNING: All maintenance activities shall be performed by qualified personnel. Failure to do so could result in serious injury. For any service related concerns, call Cybex Customer Service at 888-462-9239 (for Cybex customers living within the USA). For customers living outside the USA, call 508-533-4300 or fax 508-533-5183. NOTE: Read and understand each procedure thoroughly before servicing.
Cybex Pro+ Treadmill Service Manual LED Functions LEDs are used to indicate the status of many of the treadmill inputs. After entering Test Mode refer to the following list to check that these LEDs are functioning properly: Heart LED – Blinks on with every signal from the contact heart rate receiver. Weight LED – Blinks on when CSAFE data is being received. Level LED – Blinks on when CSAFE data is being transmitted. Lower Left Window – The numbers indicate actual elevation.
Cybex Pro+ Treadmill Service Manual Error Codes Error codes notify you of a problem condition and are displayed on the center of the console. These codes can also help to indicate the part of the treadmill most likely to be causing the problem. Errors that present a hazard to the user provide a measure of safety by causing a one second beep, stopping the treadmill and locking out operation of the treadmill. A log of errors can be viewed and cleared.
Cybex Pro+ Treadmill Service Manual Motor Current and Voltage Motor current draw and motor voltage must be checked by a qualified service technician at the recommended intervals listed in the Service Schedule in the Preventive Maintenance chapter of this manual. For your convenience a service schedule decal is provided under the motor cover of each Cybex Pro+ treadmill. By performing these procedures you can evaluate the performance of your drive motor and help prevent premature failure.
Cybex Pro+ Treadmill Service Manual 5. Check the motor voltage. A. Plug the treadmill back in and turn it to the on (I) position. B. Enter Test Mode. C. Without standing on the belt, Bring the speed of the treadmill up to maximum speed, 12.4 mph (20 kph). D. Using a voltage meter, contact the meter’s red lead to the connector of the motor’s red lead and the meter’s black lead to the motor’s black lead on the lower board. E. Note the reading on the voltage meter then carefully remove both leads.
Cybex Pro+ Treadmill Service Manual B. Using a 7/16” Open end wrench, tighten the mounting nut that attaches the speed sensor bracket to the drive motor. See Figure 3. C. Ensure that the gap between the speed sensor and drive motor fan is even on both sides. See Figure 3. Speed Sensor Bracket Speed Sensor Gap Sensor Bracket Mounting Nut Drive Motor Fan Drive Motor Fan Mounting Nut Figure 3 5. Test for speed errors. A. Connect the power cord to a power outlet. B. Enter Test Mode. C.
Cybex Pro+ Treadmill Service Manual IR Compensation NOTE: This procedure is required after replacing the lower control board or the drive motor. Tools Required • • Phillips screwdriver Plastic (or non-conductive), flat head screwdriver 1. Please read instructions thoroughly before performing this procedure. 2. Remove the motor cover. A. Using a Phillips screwdriver, loosen three screws on each motor cover side (left and right). See Figure 2. B. Lift the motor cover center up and off the treadmill.
Cybex Pro+ Treadmill Service Manual G. Retest by walking on the belt and adjusting the IR COMP control until the running belt does not surge, vibrate or feel too slack. NOTE: You should not be able to stop the belt with your feet easily. H. Press Stop. I. Place the lower board shield into position (if applicable) and snap it in. 4. Secure the motor cover. A. Lower the motor cover into position. See Figure 2. B. Using a Phillips screwdriver, tighten the three screws on each side.
Cybex Pro+ Treadmill Service Manual Running Belt and Deck NOTE: During this procedure you will have the option to remove the running deck, running belt, rubber mounts, rear roller, front roller and drive belt. Follow this procedure from step 1 even though the heading for some of these procedures will appear before the step where you remove that part.
Cybex Pro+ Treadmill Service Manual 4. Remove the side panels. A. Pull each side panel out and off the treadmill. See Figure 5. 5. Remove the top steps. A. Using a Phillips screwdriver, remove the three screws that hold one of the top steps in place. Repeat this step for the other side. See Figure 5. B. Grasp each top step and slide it out and off the treadmill. See Figure 5. Side Panel Screws (3 Under Each Top Step) Top Steps Side Panel Figure 5 Rear Roller 6. Remove the rear roller.
Cybex Pro+ Treadmill Service Manual 7. Remove the deck. A. Using a 7/16” open-end or socket wrench, remove the ten screws and ten washers that hold the deck in place. See Figure 7. Screws (5 on Each Side) Running Deck Running Belt Washers (5 on Each Side) Deck Support (1 on Each Side) Figure 7 8. Remove the deck stiffeners. A. Using a 1/2” Socket wrench, remove the two whiz-lock screws that secure the deck pivot shaft to the frame. See Figure 8.
Cybex Pro+ Treadmill Service Manual B. Using a Phillips screwdriver, remove the flat head screw securing each deck stiffener to the deck bushing. See figure 8. 9. Inspect the deck bushings. A. Inspect the deck bushings under the deck stiffeners for cracks or wear. NOTE: Replace the rubber mounts if the rubber is cracked or worn. B. Using a Phillips screwdriver, secure each deck stiffener with the flat head screws removed in step 8B. C.
Cybex Pro+ Treadmill Service Manual 14. Secure the front roller. Open grooves on Front Roller A. Slide the front roller into the running belt. NOTE: It doesn’t matter which way the running belt goes. B. Be sure the drive belt is around the flywheel pulley and the front roller before attaching the front roller. C. Using a 9/16” socket wrench with a 3” extension, attach the two screws that fasten the front roller to the frame.
Cybex Pro+ Treadmill Service Manual 20. Secure the end caps. A. Using a Phillips screwdriver, tighten the screw that holds each end cap in place. See Figure 4. 21. Secure the motor cover. A. Lower the motor cover center into position. See Figure 2. B. Using a Phillips screwdriver, tighten the three screws on each side. NOTE: Be sure the screws are catching the center motor cover’s holes. 22. Adjust the running belt tension and tracking. A.
Cybex Pro+ Treadmill Service Manual B. Slip the drive belt around the flywheel pulley and off the motor. See Figure 14. 5. Disconnect the motor cables. Screws (Loosen) ! WARNING: Do not touch components on the lower board. A charge can remain after unplugging the power cord and turning off the treadmill. Nuts A. Observe the “armature LED” on the lower board (labeled ILT4). B. After the armature LED goes off proceed to step 5C. C. Pull up on the lower board shield. It will snap out. D.
Cybex Pro+ Treadmill Service Manual B. Using a 9/16” socket wrench with a 3” extension, insert the two screws that fasten the front roller to the frame. NOTE: Tighten each of the two screws evenly, making sure not to tighten one screw too many turns before moving to the other screw. See Figure 9. 8. Secure the rear roller bolts. A. Using a 3/4” socket wrench, tighten each rear roller bolt evenly, making sure not to tighten either bolt too many turns before moving to the other bolt.
Cybex Pro+ Treadmill Service Manual 10. Remove the drive motor brush access covers. A. Squeeze each of the two rectangular brush covers to remove it from the motor. See Figure 15. Drive Motor Brush Access Cover Round Brush Cover Figure 15 B. Lift off the round brush cover. See Figure 15. If necessary carefully pry the cover up using a flat head screwdriver. 11. Remove the brushes. A.
Cybex Pro+ Treadmill Service Manual A. Locate the brush with the two wires and slide it into the motor brush holder (located nearest the round access hole). B. Locate the brush with the one wire and slide it into the motor brush holder on the opposite side. C. Place a spring clip under each brush and push in and down. The spring hooks will grasp on to the end of the brush holder. D. Using needle nose pliers, plug the yellow brush wear indicator wire onto the fast-on inside the round access hole. E.
Cybex Pro+ Treadmill Service Manual 17. Align the drive belt. A. Confirm that the drive belt fills all grooves in the drive motor flywheel pulley and there are open grooves on the inside of the front roller. See Figure 11. NOTE: Failure to align the drive belt could cause squeaking. 18. Connect the motor cables. A. Connect the motor cable to the lower board as shown in Figure 14 (red to A1, black to A2, yellow to BW). B. Using a 1/2” socket wrench, tighten both screws on the motor saddle. C.
Cybex Pro+ Treadmill Service Manual 19. Secure the motor cover. A. Lower the motor cover center into position. See Figure 2. B. Using a Phillips screwdriver, tighten the three screws on each side. NOTE: Be sure the screws are catching the center motor cover's holes. 20. Perform the appropriate procedures. A. If you loosened the tension on the running belt (step 6A) follow the Tension and Center the Belt procedure located in the Preventive Maintenance chapter. B.
Cybex Pro+ Treadmill Service Manual 4. Disconnect the elevation motor cable. ! WARNING: Do not touch components on the lower board. A charge can remain after unplugging the power cord and turning off the treadmill. A. Pull up on the lower board shield. It will snap out. B. Disconnect the elevation motor cable from the lower board and remove it from the wire tie. 5. Remove the elevation motor. A.
Cybex Pro+ Treadmill Service Manual B. Carefully remove the wooden blocks from under the front end assembly. This will load the elevation assembly. C. Lower the elevation to zero percent. D. Stop the treadmill and turn the main power switch in the front panel to the off (O) position. 8. Secure the motor cover. A. Lower the motor cover center into position. See Figure 2. B. Using a Phillips screwdriver, tighten the three screws on each side.
Cybex Pro+ Treadmill Service Manual 4. Remove the line filter. A. Using a Phillips screwdriver, remove the two screws that hold the line filter to the lower control board bracket. NOTE: You should not need to disconnect the cables that are connected to the line filter. 5. Remove the lower control board bracket. A. Using a Phillips screwdriver, remove the four screws that hold the lower control bracket to the base. B. Remove the entire bracket with its lower board.
Cybex Pro+ Treadmill Service Manual B. Put the ground wire terminal on the stud on the lower board bracket. C. Using a 3/8” nutdriver, secure the one nut and one washer over the ground wire terminal. 8. Secure the line filter. A. Using a Phillips screwdriver, secure the two screws that hold the line filter to the lower control board bracket. 9. Secure the wires. A. Check to see that all of the cables are connected firmly in their proper place. B.
Cybex Pro+ Treadmill Service Manual B. Lift the motor cover center up and off the treadmill. The screws will stay in place. See Figure 2. C. Remove the left plastic side cover. 3. Remove the left end cap. A. Using a Phillips screwdriver, remove the screw that holds the left end cap in place. See Figure 4. 4. Remove the left side panel. A. Pull the left side panel out and off the treadmill. Power Switch 5. Remove the power switch. A. Observe the “armature LED” on the lower board (labeled ILT4). B.
Cybex Pro+ Treadmill Service Manual Line Filter NOTE: If you are replacing the line filter follow steps 7 and 8. If not skip to step 9. 7. Replace the line filter (optional). A. Disconnect the two fast-ons that go from the line filter to the lower board (cables labeled AC Line 1 and AC Line 2 on the lower board). B. Using a Phillips screwdriver, remove the two screws that hold the line filter to the lower control bracket and discard the old line filter if applicable. C.
Cybex Pro+ Treadmill Service Manual B. Connect these two power cord cables to the power switch: • The blue cable connects to the top left switch fast-on. • The brown cable connects to the top right switch fast-on NOTE: You will connect the ground in step 10D. C. Connect the line filter fast-ons to the power switch. • The white cable connects to the bottom right switch fast-on. • The black cable connects to the bottom left switch fast-on D.
Cybex Pro+ Treadmill Service Manual 3. Remove the display board. A. Disconnect these cables from the display board: the display cable (2 connectors), the two upper switch membranes, the lower switch membrane, the contact heart rate cable, the CSAFE board to display board jumper and the upper to lower board jumper. See Figure 23.
Cybex Pro+ Treadmill Service Manual 7. Secure the console back. A. While being sure not to pinch any cables, use a Phillips screwdriver to secure the nine screws that hold the back cover to the console front. 8. Calibrate speed. A. Follow the Speed Calibration procedure located in this chapter. Contact Heart Rate Board NOTE: This procedure will cover the contact heart rate board, grips and cable. Tools Required • • Phillips screwdriver ESD (Electro Static Discharge) grounding strap 1.
Cybex Pro+ Treadmill Service Manual Contact Heart Rate Grips Tools Required • • • Phillips screwdriver Needle nose pliers Wire cutters 5. Remove the old heart rate grips and cable. A. Using a Phillips screwdriver, remove the two screws from each lower grip. See Figure 25. Upper Grip Cap B. Using a needle nose pliers, carefully disconnect the wire from each metal contact. C. Pull the grips and cap off each handrail. D.
Cybex Pro+ Treadmill Service Manual 7. Install the new heart rate grips. A. Using the needle nose pliers, carefully connect the heart rate wire to each grip. NOTE: Ensure that the red heart rate wire is connected to the top grip and the black heart rate wire is connected to the bottom grip. See Figures 25 and 26. B. Place the top grips, bottom grips and cap in the correct position on the handrail. See Figure 25. C. Using a Phillips screwdriver, install the two screws securing the bottom grips.
Cybex Pro+ Treadmill Service Manual A. Gently push the CSAFE connector into its port on the display board. See Figure 23. B. Using a Phillips screwdriver, secure the CSAFE board with the three screws removed during step 3B. NOTE: Do not overtighten. 5. Secure the console back. A. While being sure not to pinch any cables, use a Phillips screwdriver to secure the nine screws that hold the console back to the console front.
Cybex Pro+ Treadmill Service Manual A. Pull up on the lower board shield until the shield snaps out. B. Disconnect the display cable (P1 and P2) from the lower board. See Figure 27 . NOTE: “Right” and “left” denote user orientation. Console Back Cover Bottom Hole Screws (9) Left Junction Covers P3 and P8 Connectors on Upper Display Board Wire Holder Screws (3) Display Cable Upright Shield P1 and P2 on Lower Board Access Hole Screws (4) Left Side Cover Figure 27 C.
Cybex Pro+ Treadmill Service Manual F. Using wire cutters, cut the cable at its center near the junction and pull both ends out of the treadmill. NOTE: Pull the upper end up and out and the lower end down and out. NOTE: Display cables have a revision number label so that you can verify that you have the latest revision of the cable. 6. Attach the new display cable. Small P1 Connector Up A. Connect the display cable (P3 and P8) to the upper display board. See Figure 27. B.
Cybex Pro+ Treadmill Service Manual Display Overlays NOTE: This procedure will cover the upper and/or lower display overlay. They are removed and replaced the same on the Cybex Pro+ treadmill. Tools Required • • • Phillips screwdriver ESD (Electro Static Discharge) grounding strap Razor blade 1. Disconnect the external power source. A. Turn the main power switch on the left side to the off (O) position. B. Unplug the treadmill from the power outlet. 2. Remove the console back. A.
Cybex Pro+ Treadmill Service Manual 5. Secure the console covers. A. Using a Phillips screwdriver, tighten the six screws that hold the console front to the frame. B. While being sure not to pinch any cables, secure the console back to the console with the five Phillips screws. 6. Test the new display overlay. A. Turn the main power switch to the on (I) position. B. Plug the treadmill into the power outlet. C. Try each key to be sure that it functions properly.
Cybex Pro+ Treadmill Service Manual Parts List ITEM QTY. PART NO. DESCRIPTION ITEM QTY. PART NO.
Cybex Pro+ Treadmill Service Manual ITEM QTY. PART NO. DESCRIPTION ITEM QTY. PART NO.
Cybex Pro+ Treadmill Service Manual This page intentionally left blank.
102 108 124 107 100 59 61 60 70 43 42 146 128 62 124 105 64 125 129 106 53 112 119 201 212 101 132 127 118 111 71 104 126 53 110 125 99 8 130 133 131 65 208 203 133 131 41 116 207 209 208 125 93 204 206 113 42 213 211 130 5 146 43 120 AV Option 124 103 116 200 73 207 74 73 75 74 204 74 73 98 69 68 2 202 208 2 96 209 205 210 2 46 50 44 88 92 80 48 89 95 45 57 90 81 29 38 94 49 44 51 4 40 76 39 147 47 3 36 56 19 67 53 30
208 109 208 208 - 240V 125V 240V 240V 50 60 60 50 Hz Hz Hz Hz (AW-19523 (AW-16640 (AW-16639 (AW-16638 POWER POWER POWER POWER 20A DOMESTIC 115V - EC-19869 (RP220-20-4.7) 20A DOMESTIC 220V - EC-19869 (RP220-20-4.7) 15A INTERNATIONAL - EC-18896 (DSC1000-4-10-4.7) CORD) UK CORD) CORD) CORD) LINE FILTER AW-16572 (DOM) AW-16938 (DOM) N/C < 16% LINE AW-17163 (INTL) BLK WHT INTERNAL MAX ELEV.
