Cybex Eagle® Incline Press Owner’s and Service Manual Strength Systems Part Number 11150-999 K www.cybexinternational.
Cybex Eagle® Incline Press Owner’s and Service Manual Strength Systems Part Number 11150-999 K Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc. Eagle® and its mark are registered trademarks of Cybex International, Inc. DISCLAIMER: Cybex International, Inc., makes no representations or warranties regarding the contents of this manual.
Table of Contents 1 Safety Safety. . . . . . . . . . . . . . . . . . . . . . . . . . Warning/Caution Decals . . . . . . . . . . . Regular Maintenance Activities . . . . . . Using Proper Form . . . . . . . . . . . . . . . 1-1 1-2 1-5 1-5 2 Exercises General Exercise Guidelines . . . . . . . . 2-1 3 Customer Service Contacting Service. . . . . . . . . . . . . . . . Ordering parts . . . . . . . . . . . . . . . . . . . Return Material Authorization (RMA). . Damaged Parts . . . . . . . . . . . . . . . . . .
Cybex Eagle 11150 Incline Press Owner’s Manual 1 - Safety Safety Read the Owner’s Manual carefully before assembling, servicing or using the equipment. It is the responsibility of the facility owner and/or owner of the equipment to instruct users on proper operation of the equipment and review all labels. WARNING: Serious injury could occur if these safety precautions are not observed: User Safety Precautions • Obtain a medical exam prior to beginning an exercise program.
Cybex Eagle 11150 Incline Press Owner’s Manual • Make sure that each machine is set up and operated on a solid level surface. Do not install equipment on an uneven surface. • Make sure that all users are properly trained on how to use the equipment. • Make sure there is enough room for safe access and operation of the equipment. • Perform regular maintenance checks on the equipment.
Cybex Eagle 11150 Incline Press Owner’s Manual 3. Anchoring holes are provided on the feet of the frame. All anchoring locations must be used when anchoring the equipment to the floor. 4. Due to the wide variation of flooring on which machines may be anchored or installed, verify anchoring method and anchoring fasteners with a qualified and licensed contractor. 5. A minimum pull out force of 220 lbs/100 kgs is required for each anchor position.. 6. Do not use machine until it is properly anchored.
Cybex Eagle 11150 Incline Press Owner’s Manual A CAUTION B Personal injury may occur. Keep away from moving parts to avoid injury. 4000Y316-4 C CAUTION Seat may fall if improperly engaged. Verify seat is secure before exercising to avoid injury.
Cybex Eagle 11150 Incline Press Owner’s Manual Incline Press - 11150 B (Both Sides) B A C C B DESCRIPTION PART NO. A. Warning Decal .............4605-381-4 B. Caution Decal...............4000y316-4 C. Caution Decal...............
Cybex Eagle 11150 Incline Press Owner’s Manual Regular Maintenance Activities Preventative maintenance activities must be performed to maintain normal operation of your equipment. Keeping a log sheet of all maintenance actions will assist you in staying current with all preventative maintenance activities. The preventative maintenance actions are described in detail in Chapter 5. Briefly, they include: Daily 1. Clean upholstery. Weekly 1. Inspect all nuts and bolts for looseness. Tighten as required. 2.
Cybex Eagle 11150 Incline Press Owner’s Manual 2 - Exercise MUSCLES USED Intended Use The intended use of this equipment is to aid or improve general physical fitness and exercise. For Commercial use. Instructions Read and understand all instructions and warnings prior to using this machine. See Chapter 1, Safety in the Eagle Owner’s Manual or consult with floor staff.
Cybex Eagle 11150 Incline Press Owner’s Manual Set Up 1. Adjust seat bottom and back so that handles are at mid-chest. 2. Select hand position that allows hands to finish in front of the shoulders. Basic Movement 1. Push handles forward until your arms are fully straightened Advanced Movement 1. Using a slightly wider hand position bring the handles in slightly. Push handles forward and to the center until your arms are fully straightened.
Cybex Eagle 11150 Incline Press Owner’s Manual 3 - Customer Service Contacting Service Hours of phone service are Monday through Friday from 8:30 to 6:00 p.m. Eastern Standard Time. For Cybex customers living in the USA, contact Cybex Customer Service at 888-462-9239. For Cybex customers living outside the USA, contact Cybex Customer Service at 508-533-4300 or fax 508-533-5183. Find information on the web at www.cybexintl.com or by e-mail at techhelp@cybexintl.com.
Cybex Eagle 11150 Incline Press Owner’s Manual 1. Call the Customer Service Hot Line listed above for the return of any item that is defective. 2. Provide the technician with a detailed description of the problem you are having or the defect in the item you wish to return. 3. Provide the model and serial number of your Cybex equipment. 4. At Cybex’s discretion, the technician may request that you return the problem part(s) to Cybex for evaluation and repair or replacement.
Cybex Eagle 11150 Incline Press Owner’s Manual 4 - Assembly TOOLS REQUIRED • • • • • • • 7/32” Allen wrench 3/4” Allen wrench 9/16” Wrench External snap ring pliers Phillips screwdriver Medium weight automotive engine oil Torque Wrench NOTE: Two people will be required for this procedure. NOTE: It is the responsibility of the facility owner/owner of the equipment to ensure that there is appropriate clearance around each machine to allow for safe use and passage. 1.
Cybex Eagle 11150 Incline Press Owner’s Manual D. Rotate cam and disconnect weight stack belt from cam (by loosening the two set screws on the belt clamp with a 7/32” Allen wrench). See Figure 1. E. Locate the pulley bracket that is located near the cam. See Figure 2. F. Remove bolt, washer and hex nut securing the pulley to the pulley bracket. Set Screws Cam Figure 1 G. Remove pulley from pulley bracket. Cam Bolt H. Remove one of the two BHSCS (Button Head Socket Cap Screws) securing the pivot shaft.
Cybex Eagle 11150 Incline Press Owner’s Manual F. Loosen bottom two screws shown in Figure 6. NOTE: Do not remove the bottom two screws. G. Remove the top two screws securing the back shroud. See Figure 7. Screw (loosen do not remove) H. Carefully slide rear shroud assembly upward and remove. 6. Install the weight stack. Figure 6 A. Note how the increment weights are installed. B. With an assistant holding the increment weights, move the adjusting knob to 0 lbs.
Cybex Eagle 11150 Incline Press Owner’s Manual 7. Belt Routing. A. Verify belt is routed through top of pulley bracket and then route end of belt down to the top weight. B. Carefully lift top weight and verify that the position of the belt clamp (on the top weight) is aligned properly with the top pulley bracket (on the machine). See Figure 10. C. Slide belt through slot in belt clamp. D. Verify belt and insert are installed properly, as shown in Figure 11A.
Cybex Eagle 11150 Incline Press Owner’s Manual 8. Install back shrouds. A. Carefully place shroud back into position on the two bottom screws. See Figure 14. B. Install the top two screws securing the back shroud. See Figure 15. C. Install the three Phillips head screws securing the top (back) shroud. See Figure 16. Screw Figure 14 9. Install weight plate decals. NOTE: You have the option to use pounds, kilograms or both. A. Slowly and carefully peel off back side of decal. See Figure 17.
Cybex Eagle 11150 Incline Press Owner’s Manual This page intentionally left blank.
Cybex Eagle 11150 Incline Press Owner’s Manual Chapter 5 - Maintenance All preventive maintenance activities must be performed on a regular basis. Performing routine preventive maintenance actions can aid in providing safe, trouble-free operation of all Cybex Strength Systems equipment. NOTE: Cybex is not responsible for performing regular inspection and maintenance actions for your machines. Instruct all personnel in equipment inspection and maintenance actions and also in accident reporting/recording.
Cybex Eagle 11150 Incline Press Owner’s Manual More Difficult Stains • Dampen a soft white cloth with a solution of 10% household bleach (sodium hypochlorite), 90% water. Rub gently. Rinse with a water dampened cloth to remove bleach concentration. • The same procedure can be used with full strength household bleach, if necessary. • Allow bleach to puddle on the affected area or apply with a soaked cloth for approximately 30 minutes.
Cybex Eagle 11150 Incline Press Owner’s Manual 4. Guidelines for cleaning front panel: • Use clean soft cloths or sponges for application of cleaners and again for washing and rinsing. • Follow up the application with warm water rinse. • Don’t use abrasives or high alkaline cleaners. • Don’t leave cleaners on for long periods, wash immediately. • Don’t apply cleaners in direct sunlight or at elevated temperatures. • Don’t use scrapers, squeegees or razors. • Don’t clean with gasoline.
Cybex Eagle 11150 Incline Press Owner’s Manual Weekly Procedures 1. Check all nuts and bolts for looseness. Tighten as required. 2. Inspect all belts (entire length) for any non-uniformity and wear.
Cybex Eagle 11150 Incline Press Owner’s Manual 3. Some machines use cables in addition to belts. Inspect all cables for wear or damage and proper tension. When inspecting cables, run your fingers on the cable, paying particular attention to bends in the cable and attachment points. Replace all worn cables immediately. The following conditions may indicate a worn cable: • A tear or crack in the cable sheath that exposes the cable. See Figure 1. Figure 1 • A kink in the cable. See Figure 2.
Cybex Eagle 11150 Incline Press Owner’s Manual 4. Inspect bars and handles for wear, paying particular attention to tab area connecting points. Replace all worn handles immediately. 5. Inspect snap links for proper latching (indicates wear). Replace all worn snap links immediately. 6. Inspect for loose or worn grips. Replace all loose or worn grips immediately. 7. Inspect all labeling for readability. This includes instructional placards, warning and caution decals. Replace all worn labeling immediately.
Cybex Eagle 11150 Incline Press Owner’s Manual Environment Static Electricity - Depending upon where you live, you may experience dry air, causing a common experience of static electricity. This may be especially true in the winter time. You may notice a static build-up just by walking across a carpet and then touching a metal object. The same can hold true while working out on your unit. You may experience a shock due to the build-up of static electricity on your body and the discharge path of the unit.
Cybex Eagle 11150 Incline Press Owner’s Manual Maintenance Page 5-8
Cybex Eagle 11150 Incline Press Owner’s Manual 6 - Service Please refer to the next several pages for parts lists, exploded-view diagrams. NOTE: All inspections and repairs must be performed by trained service personnel only. Cybex will void warranty if non-Cybex replacement parts are used.
Cybex Eagle 11150 Incline Press Owner’s Manual This page intentionally left blank Service Page 6-2
Cybex Eagle 11150 Incline Press Owner’s Manual INCLINE PRESS PRODUCT NO. 11150 (Both Sides) A L E F D C I A K I N M B G A H B NOTE: See exploded-view diagram for location of J (serial number decal). DESCRIPTION A. B. C. D. E. F. G. PART NO. Caution Decal .................... 4000Y316 Caution Decal .................... 4520-362 Warning Decal ................... 4605-381 Placard Decal .................... 11000-610 Eagle Plaque ...................... 11040-789 Back Pad w/Wear Cover ...
QTY 5 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 2 2 4 2 2 1 1 1 2 1 2 2 2 1 1 2 2 1 2 1 1 8 1 2 2 1 4 1 1 1 1 1 1 1 1 1 5 2 2 1 1 ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 Service Page 6-4 4628-312 51198 4605-550 08014 11000-002 11000-201 11000-204 11000-205 11000-206 11000-207 11000-208 11000-209 11000-210 11000-211 11000-212 11000-213 11000-303 11000-365 11000-366 11000-376 1100
113 SERIAL NUMBER DECAL 62 115 60 76 114 112 3 68 80 76 44 83 89 54 72 76 68 60 25 64 73 80 54 70 76 108 16 88 13 103 101 44 104 70 64 104 103 69 48 54 44 93 51 INCLINE PRESS MAIN ASSEMBLY DETAIL 89 83 109 110 111 79 80 12 71 83 94 1 94 2 82 47 94 59 Cybex Eagle 11150 Incline Press Owner’s Manual Service Page 6-5
Cybex Eagle 11150 Incline Press Owner’s Manual SHROUD AND GUIDE ROD ASSEMBLY DETAIL 86 32 33 31 77 86 86 84 106 33 60 86 45 107 99 67 35 52 46 26 30 28 116 85 29 28 34 86 34 36 86 98 116 85 86 Service Page 6-6
89 83 20 90 80 89 20 21 83 14 64 64 19 97 41 11 96 90 50 64 54 64 105 42 69 18 100 Up to 3 shims as needed 101 80 15 83 89 75 48 56 92 83 89 1 80 80 1 56 89 75 48 100 92 83 18 69 83 15 42 101 96 80 Up to 3 shims as needed 105 54 64 89 RIGHT AND LEFT ARM ASSEMBLY DETAIL 64 49 10 64 90 64 19 97 41 20 21 83 89 14 89 83 20 80 90 Cybex Eagle 11150 Incline Press Owner’s Manual Service Page 6-7
Service Page 6-8 89 57 5 39 93 83 90 61 55 83 83 78 89 66 39 89 27 89 83 6 66 23 66 87 93 38 90 83 4 63 8 66 89 95 93 66 22 7 90 89 39 83 89 91 78 22 40 83 66 39 87 83 89 83 77 89 74 55 102 81 43 65 24 9 65 48 GAS SPRING AND SEAT LINKAGE ASSEMBLY DETAIL Cybex Eagle 11150 Incline Press Owner’s Manual
Cybex Eagle 11150 Incline Press Owner’s Manual BELT AND CABLE ROUTING DETAIL 67 47 2 Service Page 6-9
Cybex Eagle 11150 Incline Press Owner’s Manual TOP WEIGHT ASSEMBLY DETAIL ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 QTY 1 1 2 2 1 1 1 1 1 1 1 4 2 1 1 PART NO. 11040-366 11040-367 11040-369 11040-370 11040-427 11040-426 11040-424 11040-416 11040-425 BH030207 4700-251 BR030209 BR030220 HP016820 HP266765 DESCRIPTION Top Weight Assembly, Molded Hub, Molded Rod, Linkage Pin Rod Stem Cover Plate Cover, Top Weight Knob Pin, Weight Selector Lifting Post 15 External Retaining Ring .188 Internal Retaining Ring 1.
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183 www.cybexinternational.com • techhelp@cybexintl.
