Service manual

5302 CONFIGURATION
5302 and 5651 - Low Row
1 1 01247 Pulley Mount
2 1 4800-250 Top Weight Assembly
3 2 4700-019 Brg Flg .62 x .92 x 1.50 L
4 2 BR030206 Retaining Ring
5 2 01439 Weight Rod .625 Dia. x 65.31
6 2 01755 Guide Rod Collet-Long
7 4 08014 Pulley
8 1 HP286819 Spiral Pin
9 1 4106S055-0 Seat Cushion
•10 1 5302-51 Base Package
11 1 PP090000 Plastic Insert
12 1 4700M005 Rubber Boot
13 1 4800-570 Cable Guard
•14 2 5310P044 Weight Select Pin
•15 1 5301-201 Back Cover
•16 2 5301-310 Pulley Guard
•17 2 5301-311 Stop
18 1 02106 Half Weight Peg
19 1 HS308300 Split Lockwasher .25
20 1 JC620415 BHSCS .25-20 x .75
21 1 C-ZA00200 Half Weight
22 19 4005C062 Weight Plate 4.00 x 12.00
•23 2 PP080202 Plastic Insert, 1.19 Dia.-11 G
•24 2 PU060201 Bumper
25 1 5651-50 Low Row Frame
26 1 5651-002 Cable
27 1 02521 Caution Decal
28 1 3900-426 Vortex Decal 11.37 Grey
29 1 3900-378 Cybex Decal 11.37 Vert. Wht/Plm
29 1 3900-391 Cybex Decal 11.37 Vert. Blk/Plm
29 1 3900-419 Cybex Decal 11.37 Vert. Wht/Wht
30 1 4000Y316 Caution Decal
31 1 4800-381 Warning Decal
32 1 4800-515 Weight Plate Decal
33 1 5651-598 Placard Decal
34 2 PR060005 Weight Bumper
35 2 8630-321 Non-Slip
36 2 HC700430 BHSCS .375-16 x 2.50
37 4 HN704901 Nylon Locknut, .375-16
•38 12 HN784000 Hex Nut .50-13
39 2 JC700420 BHSCS .375-16 x 1.25
40 2 JC700424 BHSCS .375-16 x 1.75
•41 4 JC780417 BHSCS .50-13 x 1.00
42 4 JC780420 BHSCS .50-13 x 1.25
43 5 JC782830 SHCS .50-13 x 2.50
•44 1 JC782836 SHCS .50-13 x 3.25
•45 13 JS388300 Split Lockwasher .50
46 2 PP080204 Plastic Cap .625 ID x .68 OD
47 4 PP080225 Plastic Insert 1.50-8 12 G
48 1 GQ000206 Snap Link
49 1 51081 Handle Subassembly
50 Removed 10/28/08
51 2 HS347600 Washer .375
•52 4 PN660201 Hole Plug
ITEM QTY PART NO. DESCRIPTION
CABLE ROUTING DETAIL
• Not used in all configurations. Quantities will vary
depending upon type of configuration.
7. Install half weight peg (item #18).
8. Install seat cushion, for normal usage use front
holes as shown.
9. Install weight stack and top weight.
10. Tighten all hardware.
11. Install rear cover (item #15) if applicable.
12. Route cable as shown in the Cable Routing Detail
diagram. NOTE: Pulley “D” must be installed with
the rear cover open. Pulley “C” installed with guards
(item #16) and stop (item #17) to hold rear cover in
place.
13. Adjust cable for one inch of free play.
A
B
C
D
Assembly Notes (5302 and 5651)
1. Install unit in area where it will be used. Keep all shipping
packages near area of installation. Standard items include:
Shipping Package Model Configuration - 5302 5651
Base Package - 5302-51 1 x
Low Row Assembly - 5302-001 1 x
Low Row Assembly - 5651-001 x 1
Low Row Frame - 5651-50 1 1
Top Weight Package - 4700-010 1 1
Weight Package - 4700S040 1 1
Weight Package - 4700S043 1 1
Cushion Set - 5603-00 1 1
NOTE: This machine shipped with an Owner’s Manual.
Additional copies can be obtained by contacting your
dealer or a Cybex Representative at 1-888-462-9239.
NOTE: For tandem and quad (modular) configurations,
follow assembly guidelines listed on either the 5600 Modular
Center Post Assembly & Parts instruction sheet or the 5629
Tandem Center Post Assembly & Parts instruction sheet.
Also refer to all steps listed below.
2. Read and understand instructions thoroughly before
assembling the Low Row. Refer to the exploded-view
diagram and parts list when assembling the Low Row.
3. Remove back cover (item #15). Remove pin (item #14)
securing cover at the top end, and lift out.
4. Install Pulley mount (item #1).
5. Install column (item #22) to base (item #10). NOTE:
5651 configuration does not have a base (item #10) or
back cover (item #15).
6. Install frame (item #25) to column (item #22).
NOTE: Be sure
cable is routed
between pins
NOTE: Be sure
cable is routed
thru loop.