Service manual

5345 - Single Station Dip/Chin
1 2 PU060204 Bumper
2 2 01190 Vinyl Black End Cap
3 1 01167 Arm Assembly
4 2 4000-100 Pillow Block Bearing
5 2 HC700417 BHSCS .375-16 x 1.00
6 2 5580-324 Shim
7 2 01755 Guide Rod Collet
8 1 FB030213 Rod End Bearing
9 1 5345-206 Lever
10 Removed
11 1 PU060201 Bumper
12 2 4025M073 Weight Stack Guide Rod
13 8 PP090210 Plastic Insert 2.00 x 2.00 x 10-14G
14 2 PP080204 Plastic Cap .625 ID x .68 OD
15 10 PP080202 Plastic Insert 1.19 Dia. x 11 G
16 19 JS387400 Internal Tooth Lackwasher .50
17 1 JN714400 Jam Nut .375-24
18 1 5345-200 Step
19 10 HS387700 Washer SAE .50
20 1 5345-202 Frame
21 1 5345-203 Upper Arm
22 1 5345-204 Support Leg
23 1 02321 Pulley Lever
24 1 5345-303 Top Cover (Backside)
25 1 5345-304 Lower Cover (Backside)
26 2 JG780034 Leveling Guide
27 1 JD343317 Shoulder Bolt .375 x 1.00 .312-18
28 2 BG030201 Steel Plug
29 2 PR060005 Weight Bumper
30 1 JC782834 SHCS .50-13 x 3.00
31 4 JC782822 SHCS .50-13 x 1.50
32 4 JC782815 SHCS .50-13 x .75
33 2 GP000000 Pulley Assembly
34 4 GP000004 Pulley Spacer
35 2 GP000203 Pulley Center
36 1 8640-330 Spiral Pin 10 mm x 90 mm
37 12 JC780417 BHSCS .50-13 x 1.00
38 2 HC700414 BHSCS .375-16 x .62
39 REMOVED
40 1 HD383322 Shoulder Bolt .50 x 1.50 .375-16
41 1 HN664000 Hex Nut .312-18
42 2 HS347600 Washer .375
43 3 HN704901 Nylon Locknut .375-16
44 25 HN784000 Hex Nut .50-13
45 25 JC620410 BHSCS .250-20 x .50
46 1 HS328300 Split Lockwasher .312
47 1 5345-002 Cable Subassembly
48 Removed
49 2 JS388300 Split Lockwasher .50
50 2 JC700914 FHSCS .375-16 x .62
51 2 01186 Non-Slip Fabric
52 Removed
53 2 4000Y316 Caution Decal
54 1 01302 Placard Decal
55 1 02521 Warning Decal
56 1 3900-378 Cybex Decal 11.37 Vert Wht/Plm
56 1 3900-391 Cybex Decal 11.37 Vert Blk/Plm
56 1 3900-419 Cybex Decal 11.37 Vert Wht/Wht
57 4 4055M028 Foam Grip 8.00
58 1 4800-381 Warning Decal
59 1 4800-515 Weight Plate Decal
60 2 5345-319 Rubber Grip 7.75
61 4 FB050206 Sleeve Bearing
62 2 PR400201 Grip 14.00
63 2 BR030206 Retaining Ring
64 1 4700M005 Rubber Cap
65 1 5310P044 Weight Selector Pin
66 19 4005C062 Stack Weight 4 x 12
67 1 01068 Top Weight Assembly
68 2 JC782830 SHCS .50-13 x 2.50
69 2 4700-019 Flange Bearing
70 1 HP286819 Spiral Pin
ITEM QTY PART NO. DESCRIPTION
NOTE: Attach lever arm first without shim.If arm
does not align properly then install shim
on the side that needs the most alignment.
Assembly Notes
1. Attach step (item 18) to column. NOTE: Using two
people, raise column slightly and slide step under column.
2. Attach support leg (item 22) to column. it will be necessary
to raise column slightly by placing two 1/2” washers under
each side of column in order to align holes. Secure step to
support leg. Remove washers after securing support leg.
3. Install weight stack then drive spiral pin (item 36) into third
weight plate (hole normally used for selector pin).
4. Install upper arm assembly (item 21) to column.
NOTE: Two people will be required to install upper arm
assembly.
5. Route cable.
NOTE: This machine shipped with an Owner’s Manual.
Additional copies can be obtained by contacting your dealer
or a Cybex Representative at 1-888-462-9239.